Amlogic Burning Tool - drive.google.com/open?id=1tno... Mirror - mirrorace.com/m/sB4Y Rom that fixed my x96 - drive.google.com/open?id=1-WL... Mirror - mirrorace.com/m/ooZm Re-uploaded USB male to male cable - amzn.to/2EhHq3r
Haven't yet checked your solution, but i read the comments and must hand it to you, you help everyone (and most likely the only one who helps people). may you have good fortune :)
You're amazing, thank you. I thought mine was bricked, but what really happened was that I didn't realise the "white usb port" was the OTG port... the burning tool worked after, can't thank you enough.
Nice information thanks. In my case I have no access to the main chip, it's "blocked" but there was no need for shorting any pins, there was no reset button and no reset hidden behind the "AV out" as many point out. In my case I had to tear apart the box and found a push button for reset, that did the trick, no shorting required. Now In trying to fully identify my tv box and firmware, a backup sounds good before burning anything.
Million thanks, you're lifesaver! My X96 2G/16GB was brick and just has a red light when supplying power. Try so many solutions out there on the internet for whole this week, but failed. Now, I follow your instruction, and it works. It takes me only 30 mins. Liked and subscribed!
bought some no name atv box at goodwill for 3 bucks with android 7 on it, bricked it on an update, and two days later this is the only source i could find to tell me what pins i needed to short to get into burning mode. thanks! back up and running on atv9 now
What?!; D That is freaking awesome. I never would have believed that method would work. Man I got schooled to day. :) I have a non loading OS. It boots but my x96 p212 just lost the image. So even though this would be overkill, I still want to try it, but not on my box. A bricked one for though. Again, in case I didn't say it already, thank you. Awesome video, amazing tips.
For anyone failed on the short method on these two pins. Mine X96 2+16G is an earlier version, you can tell by the label which is different to the video. I have shorted the first two pins next to arrow more than 50 times, didn't work. What you need to do is short the pin 5 & 6( maybe 4 & 5) count from the diagonal corner of the arrow. Don't worry about burn the chip, I tried all the pins next to each other. I can confirm it works every time, without second delay. You don't even need the power plug in, usb cable only. When it work for you, please comment and help others to try.
Your video worked great, however, you only need to take cover off box, don’t worry about taking the board out. And I had to use a different firmware, xannys. But thank you for the easy to follow step by step video. Kudos
The bootloaders are both RAM and CPU specific, you can flash any DDR3 S905x firmware on another DDR3 S905x device even if its not built for that device.
It worked for me!! However i randonly short any 2 pin, not the 2 pin beside the arrow. Others if you face the same issue, please try any 2 pin around the chip.
Hi I managed to short the Nand pins (the first two as you said) - of course there was no reaction that I could see. I finally got to download the correct usb tool (I run win10) and it runs up. Trouble is there is no sign of my device. I did as you said - plugged in the USB and then the power but the device isn't listed. What do you suggest I try now?
Olá, parabéns pelo excelente conteúdo. Minha placa é uma "mxq-ep-2-v1.0", alguma dica de como posso encontrar o ponto de curto para realizar o procedimento?
hello I have a mecool pro w she does not have the reset button I've already opened it all I did not find this button where it is ezatamente the place to do that short to be known on the pc ????
You don't need to disassemble your X96, you take a cotton swab, cut a side to remove the cotton and insert it into the AV connector at the bottom and you will feel a switch. You push the switch until the transfer begins and you release it.
Hi. I got Transpeed T98 6K H6 box bricked. No reaction at all. Computer see the device. Flashing start but it always stop at 62% with error couldn't download boot1 :( Tried all the FWs available for that specific model. All stops at 62% :( Is this as you said that alot of them are different? Depending of factory?
Hi i need your help. I have x96 and is burned. I want repair it but i dont see name of transistor. Its power transistor.There are 2 transistors in nhere N633 and my burned A7 and i dont see what more. Help me!!!!
I have the same problem like MikeG7. My X96 mini only shows the red light when plugged in and the instructions you've posted doesn't work. It is not seen by the PC. The nand pins are not visible. Is there any another way to access the flash mode? Thanks
I have a95x I start in Usb Burning Tool and go to 7% and stop Disk Dialize/Send Command/Error Result Every turn red light no picture,and dont turn on Help Sorry for mu bad English
Hi, I have a 1g X96 mini plus and it turns out that I don't know what happened to me that the system went away and I don't know what I did that when trying to load the firmware it does not go beyond 9 percent and it gives me this error and I don't know what to do since I have to prepare something that I don't know that's what makes me
I have a Cubetek 4k android box. Once during the hard reset, the power cut was interrupted due to which it was not fully reset. Then when the power is turned on, only the Android box logo is visible. There is no process even after turning on the power by pressing the hidden button. kindly help me.
Hi bro, did you touch the 1st and the 2nd or the 2nd and the 3rd pins? So, we just need to use the screwdriver and not tweezers? Can I do the same thing on other tv box?
My friend can you help with dia h96plus device android 5.1 amulegek s905 i can not find it flash i have stopped working and when it is running, it works red light please help if you can and thank you for these.
I found a much simpler method to unbrick mine. There's a reset button in the AV port. Press and hold it with a toothpick. Then, plug in the power cable. Count to 20. You should be in recovery mode.
Gt1 ultimate 3gb/32gb. I used burn-card-maker But i have not checked ´´erase bootloader'´. So now its bricked. The light is turning on but no hdmi 1 is detected by my tv. I dont have a male to male usb, so is it possible to just shortcut the nand and then flash directly the box with my micro sd. You think it may work ??
No, as far as I know the nand short method only works when connected to a computer directly with a male to male usb cable. This is due to the recovery partition being corrupted.
Ah. Thanks!! But i finally got my gt1 ultimate (A706Dmodel) recognized by usb burning tool. I thougt my diy usb cable was falty. But the trick is to connect the box to the laptop, then shortchut the emmc. No charger/adapter needed. And sometimes i have to push the reset button before shortcutting and then release it after.
Hello, I have my X96 with S905X chip, I can connect with the USB cable, but when I press start on the usb burning tool, it disconnects for the process and shows a sign [0x10105002] Romcode/Chinese letters DDR/Chinese letters/USB Chinese letters. What can be?
Mxqpro box not detectingg in win7 OS. I have tried several time with reset button and shorted the pin lines. Not working. Usb burning tool not detecting . Please help to this problem
I have a Tv Box with an AMlogic S905L processor, and only this Rom works. Did you manage to update this TV Box? can you provide the ROM you used if you were able to successfully update your TV box with another rom? thank you in advance friend!!!
it seems wish pulled a fast one on me and gave me an odd bastard box 😣 does anyone know where id find firmware for an mxq pro 4k with a 3229 rk thats updated 7.1.2 ?? ive been wondering if i should step down my android but i dont really have those skills so im trying to do like this vid..my predicament is an odd one :-/
Respected sir, Can you make a video on pin short method for X96 mini too. I have a X96 mini which turns on with blue light with blank black screen no booting Logo no chance to reset to factory settings unable to flash with USB burning tool. ANY HELP IS APPRECIATED......THANKING YOU ANTICIPATION.