Undermount Drawer Slides Made Easy 

The video is so good, detailed in every aspect. Thank you for the nice work!

Wes, great demo on installing those drawer glides. I’d like to see how you installed & figured out how to put the glides in & the thought behind placement.

I’ve never used these drawer slides so I’ve learned a lot. Thanks for another great video Wes.🔥🔥🔥🔥🔥🔥

I love your videos.

If Blum /Salice or any other company designed a btm. mount system to retrofit existing side mount drawers , I think theyd sell a lot. (1” difference) nice video!

Wes, you make it look so easy. I converted two door cabinets I had to drawer cabinets two weeks ago, so I just made my first drawers with bottom mount drawer rails. Wish I had seen your video first, but intuitively I ended up doing it pretty much the same way you demonstrated it, except I used a hand router for the grooves and I glued the drawers together (no nails). All turned out fairly good, but I have yet to decide on drawer fronts. I made one mistake, though… I routered the grooves slightly deeper than they needed to be (for a little wiggle room). This would have not been a problem, EXCEPT when I glued and clamped the drawers together I also clamped the centers of the drawers, which of course had no ‘stop’ in form of the front and back pieces between the sides, causing a minor bow on one of the drawers. Later, I couldn’t figure out at first why one of drawers didn’t easily slide onto the rails like the others, until I looked from below and saw the slight bow on one side. Needless to say, the drawer slides I ordered in bulk also had no instructions or drawings with dimensions included, which didn’t help. Next drawers should be easier. If there will be a ‘next’… 😬

Thanks for sharing

Thnx I can understand now

Wes bringing back fond memories of my mid 80’s college days working in a cabinet shop lol. We had a bench belt sander we would sand the cut top edges tilting them up/down ever so slightly to round over. (Fastened with staples too) Probably did 1000’s of ‘em. Back in the days of oak raised panels and sometimes arched panels, sure you remember those days well. Question- what make model hardware are those? Blum?

Thanks Wes

Great video as always Wes but who's brand of slides are you using? Around here we use mostly blum 563's and they require 1/2 inch material on the drawer sides and you deduct 5/8" from the opening to get your drawer width! 3/8 would be a deal breaker. Just wondering because I have never encountered 3/8

Nice video...........Question for you - I may have missed it, but what thickness dimensions are you using on your plywood stock? 1/2 inch for the drawer sides and 1/4 inch for the drawer bottom?

off subject if you were installing side mount slides can you deduct an extra 1/32 or 1/16 off the total width. Just to be safe so that the box will not be tight. would the slides still operate properly.

I have Blum under mount drawer slide but they aren’t soft close. Do I need to replace the entire slide to make them soft close ??

Would you mind give us the length dimensions please!

Can I put 28" long drawers on "standard" 24" undermount drawer rails?

what happened to using Blum

Wes, I have a small one man cabinet shop and have tried to use dovetail drawers as a selling point for my work. Question is, do you find dovetails much of an issue? Do people really care or even know the difference?

Can you show how to make a drawer with out table saw and nail gun? Would be great

I'm enjoying your video, but at 2 minutes in, have to comment on cutting the slots for the drawer bottom, pressing down the piece with your hand over the saw blade.. My older brother came to my shop one afternoon, and unbeknownst to me at the moment, was doing the exact same type of thing. I heard him start yelling and looked over to see him clutching his hand. The piece had very unexpectedly kicked back and his fingers went right into the blade. I drove him to the local ER, they transported him to Duke for surgery. Fortunately, they got the dangling pieces of sausages reattached, but he can rule out playing piano for the rest of his life. I would very strongly discourage anyone from putting their hand over the blade when making a blind cut like that.

as you slide in the bottom it looks like you cut a rabbet on it.

Can i join you please,,