Тёмный

Using solid busbars instead of cables to connect battery modules. I should have gone with 16mm bars! 

Off-Grid Garage
Подписаться 90 тыс.
Просмотров 85 тыс.
50% 1

So, here is a bit of DIY work again and I have started working on this idea to use square busbars to connect the SEPLOS Polo battery modules instead of cables. The links are only 150mm apart so I thought getting a 20x20mm aluminium bus bar was a good idea. A bit of filing and they would fit in between these terrible terminals SEPLOS has chosen for these batteries.
Well, turns out, it took me a while to file these bus bars down. But I really like the result and function... So the only bad idea here was not choosing the 16mm bus bar.
Electrical bus bar Ampacity calculator:
www.allumiax.com/bus-bar-size...
Aluminium Bus Bar:
off-grid-garage.com/cables-an...
Heat Shrink Insulation and small PINK heat gun:
off-grid-garage.com/cables-an...
off-grid-garage.com/tools/
Also visit ‪@AveRage_Joe‬'s channel and buy some t-shirts of him.
Please subscribe and join me on my journey of the Off-Grid Garage!
For more information, please check out my website with links to all the batteries, materials, devices and products I have used in my videos: off-grid-garage.com
The 'Buy me a Beer🍻'-link is here (on the website, scroll all the way down):
off-grid-garage.com Thank you for your support!
You can also click on the Thanks button under the video to support the channel. Thank you, if you have already!
T-Shirts, caps, mugs and more in our merch-shop:
off-grid-garage.com/merch
**** These are the batteries you are looking for ****
🔋➡EVE LF280/304 LiFePO4 cells 3.2V/280+304Ah: off-grid-garage.com/batteries/
🌞➡Solar charge Controllers, Inverters and accessories: off-grid-garage.com/solar-cha...
🔧➡Tools, Analysers and Testers: off-grid-garage.com/equipment/
📈➡ Battery Tests and Results: off-grid-garage.com/battery-d...
🔌➡Batteries, charger and accessories: off-grid-garage.com/batteries-3/
⚡➡Cables, Inverters and Electronics: off-grid-garage.com/electronics/
The Sunfunkit DIY battery. Great product to build your own 12V battery. Use OGGA at checkout to get 6% off. More info here: off-grid-garage.com/diy-kits/
Video review: • The Sun Fun Kit Experi...
Best prices for Victron gear in Australia: Auto Parts Co has you covered.
www.autopartsco.com.au/?pd_pr...
(they have 4WD parts and accessories too)
Take a live sneak peek at the Off-Grid-Garage in the Victron VRM World (link at top of the page):
off-grid-garage.com/victron-c...
Here is my Tesla referral link, if you want to buy any Tesla accessories or even order a vehicle. This is a great way to support my channel. Thanks a lot to everyone who have used it so far 🙏 www.tesla.com/en_au/referral/...
My other (German) RU-vid channels:
/ offgridgarageaustralia
Please don't leave any links in your reply. RU-vid will not publish your comment in this case.
If you decide to sent me an email, I really appreciate your time and effort for doing this. However, please consider leaving a comment under my videos instead as I may not be able to reply to your email due to the sheer amount of messages I'm receiving.

Наука

Опубликовано:

 

9 авг 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 450   
@billmiller4800
@billmiller4800 11 месяцев назад
You may need to be concerned about the type of metal of your bolts with the Aluminium. If they are dissimilar metals the reaction would potentially cause resistance and heating. So, a bit of grease may be in order. Also, I would widen the bolt hole slots 1 mm inline with the bar to account for expansion/movement. With no way to handle expansion, you could loosen or even break things.
@reginaldpotts2037
@reginaldpotts2037 9 месяцев назад
As well as slot the holes in the bus bars vertically to allow for movement perhaps you could use a longer bolt with a cut down stiff spring & washer to keep tension on the bus bar but allow it to move. Loctite would help the bolt threads unwinding over time but not sure how that would affect conductivity.
@flex-ranger2
@flex-ranger2 11 месяцев назад
Hi Andy, I'm also in Aus. Shoot me the dimensions and I'll design some snap on covers for the bolts if you like and print them for you. Can be my little donation for all you efforts with the channel we all love. 👍
@lyfandeth
@lyfandeth 11 месяцев назад
Artisanally crafted bespoke busbars. Andy, should take custom orders for those!
@beebop9808
@beebop9808 6 месяцев назад
A tip to throw in the toolbox for future reference. A power circular saw makes short work of aluminum stock machining. A finish blade having as many teeth as readily available for the saw diameter you have and carbide tipped teeth. Makes beautiful cuts that require little or no finishing after the cut. When making cuts don't be afraid of leaning into it. It will cut as easily or easier than the same size block of wood. Please don't skip the eye protection. Many fine chips will fly. Best not done in the presence of electrical gear without proper shielding.
@MarkusNemesis
@MarkusNemesis 10 месяцев назад
Nice to find an Aussie channel for all this stuff. The yanks are truly spoilt for choice, compared to us down under! Love the wrench casually sitting atop the unit, with two proud, 51.2v high amp bus bars right next to it 😂
@jamieharland9080
@jamieharland9080 10 месяцев назад
Hello Andy ! Cheers for the entertainment as usual !! Always smiling ! I am living off grid myself and always read the comments as everyone is an expert and maybe that helps us all ! I love copper and would of done copper buss bars i might send you a nice pair for a future project i get big long nice looking bits and pieces from time to time from power house upgrades !! Real and old copper ! Keep up the great video’s in SUNNY STRAYA mate !!
@OffGridGarageAustralia
@OffGridGarageAustralia 10 месяцев назад
Thanks a lot. I could not find any copper busbar in this size unless I bought a 4m full length. The aluminium bar works great though. Cheers.
@uziman3800
@uziman3800 11 месяцев назад
Hi Andy. Your heat shrink size looks fine. The heat shrink bubbles like that because when it hits cold bus bar. If you heat the bus bar up with the heat gun a little it will help. You can also put a small ruler under it while shrinking and stretch the heat shrink while shrinking. Or just keep the heat on it a bit longer to heat the bar up a bit more. Heat shrinked plenty copper bar building switchboards😉
@dstevens7614
@dstevens7614 11 месяцев назад
I really love ❤ you’re sense of humor!! Thanks for the Knowledge on these thing.
@AussieDev81
@AussieDev81 11 месяцев назад
That was cool, thanks for the effort and your awesome energy
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Thanks for the feedback. Appreciate it!
@jwrhynejr.6689
@jwrhynejr.6689 11 месяцев назад
Man, Andy , you are a real HOOT!
@boomermatic6035
@boomermatic6035 11 месяцев назад
You could slip a piece of PVC pipe/conduit over the cable end of the busbar, 50mm ID might work.
@ericdelevinquiere9902
@ericdelevinquiere9902 11 месяцев назад
Expansion/ Contraction on aluminum is real, that has to be allowed in your builds. Some flexibility somewhere is always a plus.
@Dreddip
@Dreddip 10 месяцев назад
The easiest solution is to leave all the bolts just a touch loose so things can move, especially when under load.
@awbean5254
@awbean5254 11 месяцев назад
Andy, Congratulations! You do some very creative projects.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Thank you very much!
@edwardvanhazendonk
@edwardvanhazendonk 11 месяцев назад
Glad you are better again, hope Silke is also back to being better!
@loucinci3922
@loucinci3922 11 месяцев назад
Stout looking busbars. I thought I was on the Pask Makes channel with all the filling - LOL. Currious what a clamp meter would show when you turned the third battery on. Wonder if it matches the BMS. Great show. thanks for sharing. Poor Joe's shirt - LOL.
@ToddDesiato
@ToddDesiato 11 месяцев назад
FYI: Without any grease on aluminum, humid air will very quickly oxidize it. If your connections are sealed tight, it takes a long time for the oxidation to creep in, but grease will block it entirely. Also, the way to make the busbars safe is to get another vented battery cabinet and put that thing inside it.
@mikedurham4448
@mikedurham4448 11 месяцев назад
smiles .. almost instantly ..
@timg6850
@timg6850 11 месяцев назад
You want the Aluminium to oxidize with air as this creates an oxide layer on top which protects it against further corrosion. This layer is too thin to have an effect on electrical resistance. The only time you would want to use grease on Aluminium is if it could come into contact with a dissimilar metal such as Copper which would cause galvanic corrosion or there is a chance of the Aluminium bus bar getting wet.
@ToddDesiato
@ToddDesiato 11 месяцев назад
@@timg6850 Are the battery terminal blocks aluminum? Is the air not humid with moisture in the morning?
@timg6850
@timg6850 11 месяцев назад
@@ToddDesiato The terminal blocks will be either stainless steel or galvanised steel to prevent galvanic corrosion with copper wire. When I talk about not getting Aluminium busbars wet, I mean immersed in water as this will stop the protective oxide layer from forming.
@teardowndan5364
@teardowndan5364 11 месяцев назад
Aluminum is a highly reactive metal and oxidizes almost instantly with atmospheric oxygen, nothing to do with moisture. Scratch aluminum to remove the oxide layer and it takes about 20 seconds to form a new one.
@c.cmanakabubba9708
@c.cmanakabubba9708 11 месяцев назад
On the lighter-side: I only got 6.5 seconds of intro music. It does set the tone, I start bouncing my head, It is a cool little riff and it peaks interest in what Andy is going to enlighten me with. On the serious-side: Everyone will comment on how they can improve what they see but do not actually put the time in to do it.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
OK, noted. I'll do more music next time! 🎸 Yes, thanks for your appreciation of my job! 🛠 I agree, a lot of comments but not many have done it themselves 😉
@garys-half-baked-offgrid-dream
@garys-half-baked-offgrid-dream 10 месяцев назад
Hi Andy, 10 out of 10 on your Loincloth idea! 👏👏👏 Love from 🏴󠁧󠁢󠁳󠁣󠁴󠁿 Gary
@PhilBoulding
@PhilBoulding 2 месяца назад
Excellent video, thank you. But your patience is legendary !! I would have swapped out for a 16mm bar lol.
@ThaVoodoo1
@ThaVoodoo1 11 месяцев назад
Andy when batteries are installed in telecom installations we never used any paste. The most important thing was to torque the connections.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Yes, say NO to paste!
@ericl5973
@ericl5973 11 месяцев назад
It is best to connect the cables on opposite ends of the bus bars to help with equal current sharing between the modules. I am running copper bus bars myself on my battery system. Those terminals generally have quite a bit of flex so thermal expansion may not be a major issue with solid mounted bus bars.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Nohhh, not for such bus bars, they can be connected from one site easily. I have done the same in my battery shelf and have never had any issues with uneven charged batteries. 250A charging and discharging current. You may want to do this for larger batteries, with more in parallel and also higher currents but for such a baby battery, that would be overkill. Also, there is no access from the bottom...
@ericl5973
@ericl5973 10 месяцев назад
​@@OffGridGarageAustralia With only 3 modules and such big bus bars, current sharing is generally not an issue. I am just considering best practice. I have 5 modules and run at low rates, I do notice the closest battery finish charging 1% ahead but that is minor. I don't remember if any NoAlOx was applied or not, but some type of corrosion inhibitor should be applied to aluminum to avoid oxide related increases in resistance.
@batterynerd8779
@batterynerd8779 11 месяцев назад
Interesting battery design. And nice solution in the end
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Thank you!
@SuperVstech
@SuperVstech 11 месяцев назад
Cute play on words Andy. Bastard filing is SOOO fun…
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Well, it is... all this hard work for half a handful of aluminium flakes...😂
@747driver
@747driver 11 месяцев назад
Cool project Andy 👍
@Paulwilliams203
@Paulwilliams203 11 месяцев назад
It is definitely pretty with the bus bars as opposed to wires and more functional as well. 👍🏻
@andreblanchard8315
@andreblanchard8315 11 месяцев назад
All that file work. Considering what you have into all the solar equipment a bench top mill would be cheap and very handy.
@opless
@opless 11 месяцев назад
92nd! no medals for me today! Hope you get back to 100% soon dude!
@ForwardGuidance
@ForwardGuidance 11 месяцев назад
Thanks for entertaining us.
@michelbassila
@michelbassila 11 месяцев назад
you're the man dear Andy
@TheDigitalMermaid
@TheDigitalMermaid 11 месяцев назад
A video on bus bars? Yes please!
@Devastatin777
@Devastatin777 10 месяцев назад
Painters tape is a great way to find holes across a weird space. put tape where you know you want holes, pull tape up and put on bar, poof measurements are perfect always =)
@lyfandeth
@lyfandeth 11 месяцев назад
Nice integration, Andy!
@jessew6757
@jessew6757 11 месяцев назад
Hi Offgrid-Garage. Great video. Two notes of observation: 1. Safety: That uninsulated spanner on top of the batteries just next to the end of busbars......uuhhhh...not advisable, especially for the viewers. I know you are experienced enough not to make a mistake but the viewers need to know, that it is extremely dangerous to put uninsulated metal tools on top of any battery ( “Do not try that at home” ), because things could go “South” pretty rapidly. All tools should be kept on the floor away from the battery whenever you are working with batteries. 2. When connecting output cables of paralleled battery bank, it is advised that the two output cables (positive and negative) be connected at the far opposite ends of the bus bars. By that I mean for example; positive out cable connects at the top of the left bus bar, and the negative out cable connects at the bottom of the right bus bar. Reason? Because this ensure a balance of currents flowing through each battery pack, since every conductor of current has some finite length thus some finite resistance and therefore when large currents are flowing, these resistances can cause imbalance of currents. Once again for the sake of viewers, it is “industry standard practice” to connect output cables at the opposite ends of paralleled batteries of a battery bank. Thanks and regards.
@warmac57
@warmac57 11 месяцев назад
3d print little box covers in desired color. Have done this on my EG4's and they work great and look great.
@Tom111060
@Tom111060 11 месяцев назад
Ever thought about using a router - alu can be machined just with the wood bits as well ...
@rattusfinkus
@rattusfinkus 11 месяцев назад
Or an electric planer
@Tom111060
@Tom111060 11 месяцев назад
@@rattusfinkus ... If you have such a narrow one at hand ...
@ahaveland
@ahaveland 15 дней назад
or a circular saw with the blade retracted so that 1mm is above the cutting plane, add stops to limit movement then cut a few passes, transverse, diagonal and side to side.
@drumminsonlive9199
@drumminsonlive9199 9 месяцев назад
I like your sense of humor keeps me grinning …😅
@Flowing23
@Flowing23 11 месяцев назад
👍👍great stuff
@k.k.-p.1164
@k.k.-p.1164 8 месяцев назад
Hallo Andy, jetzt schau ich schon länger Deine Beiträge und plötzlich taucht in Deiner Garage ein Schild von der nordhessischen Fuldametropole Kassel auf und hat mich total überrascht. Von daher musste ich Dir einfach ein paar Zeilen mit vielen lieben Grüßen aus Kassel schreiben und mach weiter so, Klaus
@chuxxsss
@chuxxsss 11 месяцев назад
Cloud down here this morning, Andy. You are hacking this one together. Hope you and your wife have fully recovered.
@Tom111060
@Tom111060 11 месяцев назад
For an interim insulation you can put some small PET bottle(neck) parts over the ends and shrink them with your heat gun to fit ... cheap and durable.
@tinu5779
@tinu5779 10 месяцев назад
I was thinking something similar: use PVC tubes, they can be (de)formed easily too.
@jacquesb5248
@jacquesb5248 10 месяцев назад
nice job!
@mpeter2012
@mpeter2012 11 месяцев назад
Hi Andy. The way you connected your load means that top battery will work harder than the bottom battery. For more even current flow it would be better to connect load to opposite sides of the busbar, so for example + to the top of the positive busbar and - to the bottom of the negative busbar (not both at the top). It will be great to see what difference will it make to the current flow through each battery. Sounds like an idea for an experiment :) many people don't realize that it will make a difference how you connect your load to parallel batteries.
@kuhrd
@kuhrd 11 месяцев назад
Over the life of these batteries though even with the extremely flat discharge curve that is not going to be much of an issue as long as they get time most days to charge up fully and the loads are mostly below 150 amps. These busbars are capable of carrying far more power than the system is likely ever going to draw from them so the voltage drop down the length of the busbars is probably not enough to really matter. Sure he could do things to minimize it like making one connection at the top and the other at the bottom but it's probably not going to matter enough. This is probably only going to be an issue if the demand on the system is over 300 amps sustained during a prolonged discharge every day for its entire life. LiFePO4 cells are typically considered end of life at 60-70% of their original capacity. The failure rate goes up substantially per cell as they continue to be cycled beyond that point. Most of these installations will reach their limit due to calendar aging, before they ever reach that limit via cycle life. It will make sense to replace them in 20-30 years just to get the additional capacity back. I would also venture to guess DIY people like Andy will keep tinkering and building for years to come; so the system we see today will look drastically different over time, as more stuff is added and the batteries age. The point I am making is that it will likely not make a big difference over the life of these batteries, the size of the busbars, and the loads that will be put on each part of the system.
@vajkfekete2635
@vajkfekete2635 11 месяцев назад
Agree. Check Tichelmann circuit. Very simple solution to this problem.
@shaynegadsden
@shaynegadsden 10 месяцев назад
it isn't required do the math and you will see the voltage drop at the maximum current is a fraction of a volt across the busbar from memory it works out to be 0.07v and considering the busbars area vs the cables if 1 cable needs to be even a fraction longer to make that connection you have instantly cancelled out any benefit
@junkerzn7312
@junkerzn7312 11 месяцев назад
Hmm. Its nice that the bus bars fit the slots. I'm a bit worried about the contact area though. If it were copper I wouldn't be as worried as the copper will deform a bit to snuggle up. But that is mighty thick aluminum... it might not deform enough to make a solid contact. Also, won't the aluminum oxidize? Those are (I assume) nickel plated contacts, but the aluminum bus bar is (?) just straight aluminum. The potential issue is that you get arcing from micro-gaps between the aluminum and terminal contacts. -Matt
@LarryKapp1
@LarryKapp1 11 месяцев назад
Not sure what paste he had , but many of the electrical ones are antioxidant .
@byronhimebaugh4574
@byronhimebaugh4574 11 месяцев назад
If the terminals are not designed to handle any other metals than copper or steel, it may be that the aluminum may get very hot from corrosion because of the metallic differences between the metals. There is a history of mobile homes catching fire from aluminum wiring because the terminations couldn’t handle aluminum.
@larkhill2119
@larkhill2119 11 месяцев назад
For the cover, Perspex bends really easily, sandblast AG on the surface. You could have drilled the 8mm holes at 90 degrees near the middle and used less length. The 90 degrees current shift would help the flux capacitor.
@jw3843
@jw3843 11 месяцев назад
Does it make any difference on charging or discharging if you place the main wires to the bus bar on the same ends or opposite ends of the bus bars? I have heard that to charge the batteries evenly and drain them evenly it is best to put the main wire connections on opposite ends.
@putteslaintxtbks5166
@putteslaintxtbks5166 11 месяцев назад
I would think that would be good, but if your bus bars are a larger amp capacity than would usually flow though them, if resistance is low, probably wouldn't make much difference.
@ganjasage420
@ganjasage420 11 месяцев назад
Generally, no. Working with mutiple cell batteries is what makes that pointless. For the most part, if the batteries are of same capacity, than it won't matter. Whichever battery needs the power, will get it if the others don't. Good healthy batteries at same capacity will discharge equally as well. As the power leaves one cell, the other cells than pour out the power as they now have higher voltage potential, thus relatively insuring all will charge and discharge at the same time. Real life isn't paper however. While those 3 banks may be 10,000mah, one may be 10,234 while the other is 10,582, and the last being 10,334. You'll want to charge to lowest rating, charging to higher will eventually damage the cells of the lower banks. Back to the main question, no, it doesn't matter where on the bar the charge/discharge is as long as resistance is low.
@ladams5356
@ladams5356 11 месяцев назад
It doesn’t matter how others would do it, what you did wrong / right blah. It’s still entertaining 👍 and worked
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Thanks, yeah, I guess it is working quite well!
@jackoneil3933
@jackoneil3933 11 месяцев назад
4:13, to bits of copper sheet bent 90 degrees in the jaws of your vice would do the trick. At 22:00 I would likely try some clear acrylic bus-bar covers 'bended' and notched to fit over them. I'd drill and tap the busbars and use nylon screws to hold them in place, and 3d print some terminal covers for the top of the buss bar connections, or cut them shorter and connect the cables in the middle or bottom of the rack.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
I like the bended acrylic covers. Maybe I can bend them snap onto the square bar or terminal. I have some leftovers from the acrylic work I did in the battery shelf. Good thinking, thanks!
@jackoneil3933
@jackoneil3933 11 месяцев назад
@@OffGridGarageAustralia Andy, I was thinking that Sign and display shops and industrial supply sources, often use clear acrylic U-channel and square tubing stock, and even flexible colored PVC channel, and some styles are bended or extruded to be narrow at the open and help grip
@tinker3962
@tinker3962 10 месяцев назад
Use liquid urethane casting kits for forming low cost custom insulators. Robust and good resistance material.
@clarencewiles963
@clarencewiles963 11 месяцев назад
Cut, file, = work 😂 it’s looking good 👍
@scuzzo7
@scuzzo7 11 месяцев назад
Hi! Probably someone suggested this but it'd be easy to design a cap for the battery terminals, there seem to be holes on the sides of the brackets that can be utilized for something sturdy and safe. Also, I don't think you should extend the bus bars beyond the top of the battery because you can just connect the cables to one of the terminals. That way you have no metal sticking out and vulnerable to metal touching it and causing all hell. And I agree with some of the comments here, grease wasn't the problem before, it must have been corrosion. Not using grease on the mating surfaces will absolutely cause corrosion and at these currents they could get hot when that happens. Really nice solution otherwise, this looks way more sturdy and with way less points of failure than a bunch of crimped cables.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Yeah, I was hoping for the inverter to test as I mentioned and maybe the longer busbar will come in handy at this point, so I didn't want to cut them prematurely.
@m_cabral
@m_cabral 20 дней назад
If you have a miter saw you can cut aluminum with most wood blades. Just check the manufacturer's instructions. Makes quick work of things like this if you set the stops to 1mm and use stop blocks for how far you want to move left to right.
@JPHER217
@JPHER217 11 месяцев назад
Looking sweet Andy. The busbars look so lucky better. What aluminium alloy in those busbars, 6060 ?
@lyfandeth
@lyfandeth 11 месяцев назад
Aluminium attached to copper...have you tried using NoALox as a grease? Copper and aluminum just don't like being roomates for long periods.
@ahbushnell1
@ahbushnell1 11 месяцев назад
Two years from now in can have a video on the heating connections. We used to use Chemfilm on aluminum that prevents the corrosion and is conductive.
@eethon1
@eethon1 10 месяцев назад
Ive had my server rack batteries like this but with twin copper bus bars on each side for the last 4 months. all good so far. expect its a bit of a ball ache to remove a battery if needed.
@JayRSwan
@JayRSwan 7 месяцев назад
Idea for the top part. You can use paint on electrical tape. Also, you'll want to grab the positive and negative from opposite ends to balance the load better. There is resistance in the bar, and the voltage will drop between batteries. This will only be a problem for larger loads.
@OffGridGarageAustralia
@OffGridGarageAustralia 7 месяцев назад
Thank you. I still have such isolating paint from our battery shelf built. The problem is, that I need to take these connections off frequently, when I test batteries. Connecting them opposite sites makes sense, if the interconnections are thin. With such a big dimensioned bus bar, it makes no difference. Especially with LiFePO4 and the very flat voltage curve, I found no benefit. The battery banks will balance out when they are almost fully charged.
@JayRSwan
@JayRSwan 7 месяцев назад
@@OffGridGarageAustralia ​ For sure! The paint on tape is messy if you have to remove and reapply. Cheers mate keep up the good work!
@dickhead7382
@dickhead7382 11 месяцев назад
Excellent
@jedics1
@jedics1 11 месяцев назад
I used made alluminium bars cut from angle extrusion, I just sanded and cleaned them just before assembly to prevent oxidization, it made for a far cleaner looking instal than the connectors that came with it which I couldnt use anyway because of the different length bolts needed at the points where those connectors need to be stacked. I have since learnt that a galvanic reaction happens because one of the terminals of the lfp cells is copper which could be creating problems but its been running fine for nearly 4 years now. I will take it all apart and re sand and clean it to see if there is a difference. Perhaps for a high power application like an Ev it might not be the best way to go but for a lowish power instal its fine.. A tip for lining up all the bolts on the bar I use promite and dab a bit on each bolt head then press the bar against them all to mark the positions to drill.
@jimmchale8750
@jimmchale8750 11 месяцев назад
remove the black plastic/rubber trim off the 2nd and 3rd battery from the bottom and then the brackets will line up correctly. It looks like they did not account for the spacing of the trim.
@fitmydashcam
@fitmydashcam 7 месяцев назад
FYI, GI busbars are Gas Insulated. Usually with high pressure SF6 (Sulfur Hexaflouride).
@cyclemoto8744
@cyclemoto8744 10 месяцев назад
Do you have a link to purchase the Seplos batteries? Thanks for the content. Cheers
@kameraadcoenraad
@kameraadcoenraad 11 месяцев назад
Seeing you calculate the amps and later drilling the holes got me thinking, it's not 18x20 anymore is it? Does it matter? 😅
@askjeroen
@askjeroen 11 месяцев назад
That will effect the max current. Lets say it's a 8mm drill hole, than it would be around 10x20 that would limit the current to 160A. The bold will take some current also, so it will be a bit above that.
@shaynegadsden
@shaynegadsden 10 месяцев назад
you put a bolt in the holes also the terminals are another chunk of metal so in reality they make no difference
@Dutch_off_grid_homesteading
@Dutch_off_grid_homesteading 6 месяцев назад
Heya, with those bush bars it looks much cleaner install. you cut to be crazy to do that with a rasp lol
@dazrichie897
@dazrichie897 11 месяцев назад
If only Andy2 dropped by when you needed him, would have taken you half the time to complete busbars
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Hahaha, beer speeds him up even further.
@VeraPinkLynn
@VeraPinkLynn 11 месяцев назад
Hi Andy, with the ampere calculation of the diameter you commit a fallacy. The holes for the screws must be subtracted from the cross section, since the screws do not represent a solid connection to the busbar. But you have enough safety margin 🙂
@LTVoyager
@LTVoyager 10 месяцев назад
Yes, smaller bus bars would have been easier. I also would have but them just long enough to span the three batteries and then attach the external cables to the same bolts as the center battery connections. This minimizes the average resistance to each battery and also removes the bars extending above the top battery. And I would have used some grease to prevent oxidation in the future as that will become a problem.
@joeldavis3489
@joeldavis3489 10 месяцев назад
This is the perfect job for a mini mill. They’re cheap at your local version of Harbor Freight
@ooglek
@ooglek 11 месяцев назад
Nice video! The tops -- cut one piece of shrink wrap long enough that it covers the top (like 22mm) and cut the loop and place on top. Then cut another short piece of shrink wrap and put it over the bar, which will hold the top shrink wrap on the bar. Then heat and shrink the wrap and cut off any extra. Might work, just a theory/idea. Cheers!
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
It needs to be detachable. I will take the cables off frequently to test other batteries...
@ooglek
@ooglek 10 месяцев назад
@@OffGridGarageAustralia It would just cover the top of the bar. First 1-3mm from the top, above the bolt holes. Basically a tiny busbar condom over the top and first 1-3mm of the sides.
@virt1one
@virt1one 10 месяцев назад
Have you considered using 16mm bus bars? Also, copper washers work well for interfacing bus bars with contact pads. Soft copper compresses nicely and form an "electric gasket". And nice idea with the "loin cloth". You should be able to just shrink wrap the tops. Cut it off if you need access later, not a big deal, you don't need access very often and heat shrink is cheap for the protection it provides. Thanks for the video! ps.. use wood slats as shims to protect soft metals in a clamp.
@OffGridGarageAustralia
@OffGridGarageAustralia 10 месяцев назад
Thank you. Yeah, 16mm, right 😄 I don't want to heat shrink the top as I often take of the cables off and connect it to other batteries... Still unsure what to do here... I could use a heat shrink and not fully shrink it so it only sits loose on the top and can be slid back over the cable.
@supermo26
@supermo26 11 месяцев назад
Lol. Funny how you said sorry for fileing over the line. What is this battery again?
@putteslaintxtbks5166
@putteslaintxtbks5166 11 месяцев назад
Yep, got the plus and negative bus bars mixed up, but because these Seplos bms's are controlled on the negative, should be a-ok!
@paulcurtis5496
@paulcurtis5496 11 месяцев назад
I think Joe has "BOOM" patches 🤔🙄😝
@ethanclement9647
@ethanclement9647 11 месяцев назад
That is einfach a job for a milling machine --don't get me wrong --a good sharp file is one of my favorite tools.
@unclejerm7692
@unclejerm7692 11 месяцев назад
Very clean looking, but are you worried at all about those aluminum bus bars fitting so tightly? Aluminum expands and contracts more so than other metals.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
They would need a good portion of current and heat to expand that much. I'm not worried about that at all.
@maxtorque2277
@maxtorque2277 11 месяцев назад
I wouldn't take the DClink off the top of the bar, i'd take it from the middle to try to balance the impedances! (won't make much difference but it will make some difference) I'd also make sure i had suitable belville washes under the heads of my bar attachment bolts to compensate for the high thermal expansion co-efficient of the alluminium bar!
@aday1637
@aday1637 11 месяцев назад
If you attach cable to the two tops of the bus bars, insulate them and run the insulated cable into a breaker box or other enclosure with switching that should suffice. I use the techniques already employed with AC current to deal with wiring. DC battery is still wonky, though in my opinion. I find too many low secure locations where contact could occur rather easily. Ah-ha, though, once the government gets involved there will be strict codes to follow so that no one gets zapped:)
@vickipps6821
@vickipps6821 11 месяцев назад
Thank you
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Thanks!
@wi4usa
@wi4usa 10 месяцев назад
Use a 3d Printer to create caps for all of your bolt holes. Andy, what would happen if each of the polos had different cells in them. Lets say the top one had LF 304's and the two bottom ones had LF 280's. Would they eventually equalize or would the LF 304 have more capacity than the LF280's?
@76queen
@76queen 11 месяцев назад
Counter sink the bus bar and use an hex bolt to secure bus bars leaving the bus bar flush.
@camielkotte
@camielkotte 11 месяцев назад
Nice one. But too short though 😅. Anyway, my idea for the top of the busbars is too cut tennis balls with openings for cables.
@andrewsmith9620
@andrewsmith9620 11 месяцев назад
Would it improve the current flow if the external connecting cables were connected towards the middle of the bus bar?
@SolAce-nw2hf
@SolAce-nw2hf 11 месяцев назад
I was thinking the same thing. Connecting in the middle at the second battery connection would spread the load more evenly and could handle up to 3 times as much.
@MegaCyrik
@MegaCyrik 11 месяцев назад
I tried the busbar calculator and im a bit confused. A 2*2mm busbar is rated for only 4,8Amp. Thats 4mm2. My 4mm2 cables are rated for 30A. Obviously im tierd and making a mistake. Please elaborate on my error.
@jeffreykropp7664
@jeffreykropp7664 10 месяцев назад
One needs a nearby friend with milling machine and lathe.....
@OffGridGarageAustralia
@OffGridGarageAustralia 10 месяцев назад
I have only virtual friends 😂
@technicalfool
@technicalfool 11 месяцев назад
Looks like you could use those square holes to mount a big acrylic gate down in front of the whole lot? Slide the gate up when you need to flick a switch or hit a button or whatever, have nothing but insulated wiring coming out from the top (or bottom). That or drill strategic holes so you can poke a tool in for resetting or flicking switches.
@AveRage_Joe
@AveRage_Joe 11 месяцев назад
Your Shirts now Andy lol😆
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Hahaha, these shirts are haunting me in my dreams!
@wi4usa
@wi4usa 10 месяцев назад
How was the heat on the bus bars once you put a load on the batteries for a while?
@piotrbpm
@piotrbpm 11 месяцев назад
Mr. Endy, we charge the plus in advance, but the minus must be charged from the bottom with such a connection.
@matija3791
@matija3791 11 месяцев назад
What? 20x20mm copper only 480A. This calculator must be kidding xD.
@clarencewiles963
@clarencewiles963 11 месяцев назад
There’s a rubber dip for tools but you can use the rubber as a paint. To make a cap for the ends 😂
@bigbaudiboiis-ne8gd
@bigbaudiboiis-ne8gd 7 месяцев назад
What program are you using to monitor?
@arvamartin
@arvamartin 5 месяцев назад
Andy, i plan to connect four 280ah 200a BMS wall batteries in parallel. Batteries are on the wall next to each other. I m thinking of using a two 2m long 40x10 aluminum busbars running under the batteries and then short 95mm2 cables to each battery. 40x10 aluminum busbars gives me 320A. As my inverter is max 240a it should be enough. However I did not find any information how long busbars can be. Is 2m ok?
@fabiomalaguti9797
@fabiomalaguti9797 11 месяцев назад
You could design, and 3D print, snap-on plastic protective covers using these indentations on the sides of the positive and negative poles on this battery pack.
@OffGridGarageAustralia
@OffGridGarageAustralia 11 месяцев назад
Yeah, can't design that, wouldn't know how. I also don't have a 3D printer.
@fabiomalaguti9797
@fabiomalaguti9797 11 месяцев назад
@@OffGridGarageAustralia If you buy a 3D printer, I'm sure you'll be in awe of your new toy. You are just the type of person who will fall in love with this toy. It can even help you a lot to make parts for a new base for your solar panels that can follow the movements of the sun.
@midnightrider3318
@midnightrider3318 10 месяцев назад
Andy, a carbide bit router for the cutouts!
@FelixRisingOriginal
@FelixRisingOriginal 11 месяцев назад
Muirhead Engineering in Archerfield can make up custom bus bars in alu, copper or other materials..
@dowlutteeasooreeanand1355
@dowlutteeasooreeanand1355 3 месяца назад
hello is it possible to parellel LIFEPO4 pack and Lithium iron NMC battery pack together with solar inverter?
@jdw1248
@jdw1248 11 месяцев назад
Hy Andy, if there is a groove on the busbar then the surface area is bigger what means better for electrical flow but you don’t have a milling Maschine. Like I know electricity is flowing on the surface.
@shaynegadsden
@shaynegadsden 10 месяцев назад
it's cross-sectional area not surface area that is the determining factor and it isn't flowing on the sufrace
@Gastell0
@Gastell0 10 месяцев назад
I am pretty sure that back of batteries have a metal cover piece to hide it all, indentation and slots on the sides are pretty clear indicator
@OffGridGarageAustralia
@OffGridGarageAustralia 10 месяцев назад
Yes, they have. It's in the other Seplos Polo video. Not a great solution though. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-t3FiFvs1xBQ.html
@danmc1313
@danmc1313 11 месяцев назад
Would love to see Seplos Mason Futronics connector / BusBar Hybrid.
@DanBurgaud
@DanBurgaud 11 месяцев назад
6:49 can you remove the plastic on that terminal?
@maritzm
@maritzm 11 месяцев назад
Just trim the plastic around the battery POS and NEG connectors... Your warranty is void anyway ;) - A quick slip of the grinder...
@panofilossas6564
@panofilossas6564 Месяц назад
Are you sure the calculator for bus-bar ampacity is correct? 20X20 = 400mm2 aluminum = 400Amps on cable. Without insulation, even more!
Далее
20KWh DIY RackMount Backup Battery for Half price
15:27
Construction Tips and Hacks That Can Save Your Career
19:46
IT'S FINALLY DONE! | DIY Massive Off-Grid Power System
27:21
Busting the 20%-80% SOC myth for LiFePO4 batteries.
17:24
When you have 32GB RAM in your PC
0:12
Просмотров 2,5 млн