Vertical blending on hood (spies hecker) 

Good to hear😁

Thanks!!

He said "1050"

Lo primero que aplica es bending

Thanks Ail Ail love to hear that✌

Not necessarily, but blending in the middle of a hood isnt always the easiest. The blending agent just makes the final outcome a little easier.

Ty !

@@Luca-lx7ol The blender actually does nothing to blend the color, its just a wet transparant coat you put on, so that paint that lands outside the spot you are aiming at doesnt " sit " on top of the panel. If it does, the paint becomes like fine dry sand, and when you clear coat over it, it looks gritty. Also, like he says, you should stay away from edges when aplying blender. You add more color depth by adding layers, which can make some colors look darker. Its the same for clear coating with some colors, especially if the original manufacter paint has very thin coats, and you paint heavy by comparison. The color doesnt actually change, but your eyes perceive it as such. Its like looking into a pool. The shallow end will appear to have a lighter blue bottom, while the deep end will look dark blue. It's ofcourse all the same when you remove the water.

​@@Seneric Thanks for the explanation, when i asked the question i was using Ppg envirobase, now i'm using Standox Standoblue and i can confirm it! Yes I know about that thickness of layer change the color or also metamerism 👍 👍👍 Good job

6

The blender is 1050

Also can use straight out of the tin,I tend to add 20 percent 6050 or 6052

Blender.... Its basically a clear basecoat.. You spray a closed wet coat of it so that the metalics from your basecoat melt into it - instead of landing on top in little unseen dimples & irregularities in the prepped factory paint....

@@thistledewoutdoors3331 thank you sir, does basic clear coat mean only clear without using hardener or special material? because I have heard certain brands specifically for blanders, because they are not available in my country / city.

he shows there, he hits full on the spot and then blends thru the outsides, he makes this steps updown and then from side to side, at the end the hood has the original color on each side/edge whic is color match for the rest of the car paint, he just blends the spot that he paints against the original pain on the hood. He does this from 4:10 forward with the base and then just clearcoat fhe whole hood

I just painted the hood. The color you sprayed is not like the rest of the original car parts What's the solution? ?

I just painted the hood. The color you sprayed is not like the rest of the original car parts What's the solution? ?

About 8-10 minutes or it depends if you paint in a camera heat room

Thanks!

It was blender base without pigment like clearcoat

looks like WB2091 from axalta

I think it's wb1051

Thanks!

Its a dry rag,works fine for firts blow,after that the yellog rag is i litlle bit kine of greasy works great for last take of without blowing air

Yes it is👍

Hey man his color match is there. No need to hate on somebody if you don't enjoy their content just don't watch mate

A blender

@@Edinxg are you using an over reduced clear before color?

👍👍!

Donde yo trabajo se le llama bulldog pero en general creo que es como una capa transparente que ayuda a que la pintura se pegue mas y ayude a eliminar Los rayones

O puede solamente ser un blend una capa de pintura ligera para que see vea del mismo color

Chromax Blender, así se llama el producto, no es Bulldog, el bulldog es un promotor de adhesión

Hola...cualquiera sea la marca o linea del producto, este esta diseñado para aplicarse a una capa mediana humeda,solamente sobre la superficie matizada original sin primario. Su proposito, es de tener una superficie humeda al momento de aplicar la mano del color,para que las perlas metalicas se acomoden o nivelen. Asi asegurar una buena nivelación o difuminado del color sobre la superficie sin saturar mucho el color. Aqui el técnico, a mi parecer a utilizado pintura a base de agua, razón por la que a cubierto el primario rapidamente. La tecnica de su aplicación es según el fabricante...en este caso, una mano humeda y posteriormente una mediana, para uniformar textura y difuminar color. Su aplicación es de una mano mediana humeda

Indeed! nice to do so.

What gun devlbiss

Devilbiss gti pro t110 cap 1.2mm nozzle

Eldaro Reis sim

Perfeito!! Não precisa polir

aeso le llamo arte es una bellesa la difuminado que al 100

Ты реально надеялся на ответ?