What is FLEX TEMPERATURE? Explained by "Captain" Joe

Подписаться 1,7 млн

Просмотров 755 тыс.

50% 1

✈️WANT TO BECOME A PILOT?✈️ bit.ly/474j06T
📗📗📗GET MY NEW BOOK amzn.to/32TH4x7 📗📗📗
📸 INSTAGRAM FLYWITHCAPTAINJOE: goo.gl/TToDlg 📸
🌐MY WEBSITE: goo.gl/KGTSWK 🌐
🛒👕---► T-SHIRT SHOP goo.gl/Svrqmx ◄ --👕-🛒
📖👨 NEW FACEBOOK PAGE: goo.gl/heUKGb 👨📖
▼▼My FLIGHT-KIT I highly recommend for you guys▼▼
MY HEADSET: amzn.to/2CrTrzz
MY SUNGLASSES: amzn.to/2VY6FNo
MY PILOT BAG: amzn.to/2DiWKux
Company iPad: amzn.to/2W1zM2n
▼▼The VIDEO EQUIPMENT I use in my studio and outdoors▼▼
MY CAMERA: amzn.to/2T1VK3g
LIGHTING: amzn.to/2szSRv4
IN-FLIGHT RECORDINGS: amzn.to/2VY7A0g
------------------------------------------------------------------------------------
Today´s topic will be all about Flex Temperature, what is good for and how often do we use it.
Prior to every take-off you need to perform take-off calculations, giving you the speed V1, VR, and V2 and they necessary flex temperature to get the needed thrust setting for the take-off roll and lift off and eventually first climb out.
The flex temperature is a assumed outside air temperature, relatively high, forcing the FADEC ( Full Authority Digital Engine Control)-unit to reduce the thrust output to reduce the engine wear of the turbine in such expected "hot" temperatures. So once applying take-off thrust by setting the thrust levers to the FLX/MCT detent, the airplane will roll down the runway with a lower power setting thus increasing the take-off with higher speeds and decreasing the stop margin available. But you can always gain full available power by putting the levers into the TOGA detent position.
The result of using a high flex temperature is that is the speeds are higher for lift-off, cause the plane won´t accelerate as quickly as it could and therefore using up more runway, resulting in a shorter stop distance and case of a rejected take-off, obviously!
If we would have used a lower flex temperature, the lift-off speed is much lower and the stop distance is much greater compared to the higher flex temperature.
So the conclusion of that is, the lower the flex temperature, so the fake outside air temperature for the FADEC, the more power will be set when applying thrust, so the closer it is to TOGA. The higher the flex temperature the more the engine is derated resulting in longer take-off roll with higher speeds and at the same time reducing the engine wear.
I hope you enjoy the video, I appreciate a thumbs up and a comment.
The videos used in the video were provided by
HamburgvideosHD
/ elbdeichkiebitz
and
MUC_Spotter
/ @mucspotter
Please make sure to check out their channels.
The thumbail pictures was provided by my instagram follower: photoaleksi
Background song, copyright free music: Stellardrone - Cepheid
See you next thursday!
Equipment I use:
Camera: amzn.to/2nEHPDM
Microphone: amzn.to/2nff2oF
Lights: amzn.to/2nEPGkU

Наука

Опубликовано:

8 мар 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 1,1 тыс.

@larryluffel777 7 лет назад

I am a FMS developer and have worked on Airbus and Boeing aircraft for 25 years, this was the best explanation I have heard for Flex temperature. Will pass this along to newbies in the office. thanks

@roberto123nogueira 7 лет назад

You really say calm and good teaching always for us Mr. captain, thank you again

@flywithcaptainjoe 7 лет назад

Thanks for you kind comment :) Greetings Joe

@ahmadtheaviationlover1937 3 года назад

@@flywithcaptainjoe correct me if I’m wrong Flex temperature is the assumed temperature of the engine. The FADEC takes control of the flex temperature and that higher flex temperatures will have a slower performance of the engines due to the higher temperature so has a slow acceleration for takeoff but has a higher speed thus reducing the runway available for a rejected takeoff should an engine failure occurs. Lower flex temperatures will have a higher power setting and a better performance of the engine. This will have a smaller takeoff roll thus having a larger runway available for rejected takeoff. The TOGA throttle setting is reduced to clb thrust and a reduction in engine noise from a passenger perspective

@jonathanjason1312 2 года назад

Kkokk

@jonathanjason1312 2 года назад

Fdtgde DM enka SMH

@neurofiedyamato8763 7 лет назад

When I saw flex I imagined the wing flexing based on the temperature:P

@FlyGuy1 4 года назад

Same

@BlueAustinMaxi 3 года назад

Neurofied Yamato when I saw it I thought of flex-tape ._.

@theonefrancis696 3 года назад

It's not that weird tho

@TwitchKoalabaerchen Год назад

Nooo ): 😞

@andresferrin4001 Месяц назад

Hahaha you nailed it!!!

@Tom-zs1ev 4 года назад

Thank you for the explanation..if I may add..Jet engines produce reduced thrust as the ambient air temperature increases. The flex temp is the highest air temperature at which the engines would produce the required thrust. The crew finds that temperature and enters it into the flight management guidance system (FMGS) - effectively telling the computer to assume the specified air temperature instead of the actual temperature. When flex (FLX) thrust is selected during take off, the engine controller produces maximum thrust for the assumed (flex) temperature.

@SeanHollingsworth 7 лет назад

One of my favorite flights back in 2013 was from LAX to ABQ on a SWA 737-700. There were only 85 people, with crew, on the aircraft. LAX was actually quite cool, ~10C, with some low clouds and some localized fog. Our density altitude was somewhere below sea level. Needless to say, Vr was very low. We got airborne very quickly, and climbed into the night sky like a ballistic missile. ;-)

@briansmobile1 7 лет назад

Joe, you're almost to 100k subs congrats!

@DDelusionMusic 3 года назад

Now it climbed to 1.37M!!

@finn7345 3 года назад

You’re at 391k subs congrats!

@fmz-4618 3 года назад

I’m here when he’s at 1.4 mil

@bharatmaheshwari1060 3 года назад

Now in March2021 he has 1.46M❤️

@bharatmaheshwari1060 2 года назад

@@MySplash911 haha right but Kelsey is going faster than Joe

@kd4pba 7 лет назад

Wow very educational. I can recall years ago where I live taking the first plane ride in years with TWA out of KRDU. I believe this was an MD-80 series, it was around 1999. It was overcast morning around 8am and humid but not hot. The plane was full. That takeoff I will not forget. The acceleration felt exponential. We were all pressed back into our seats very hard and as we gained speed it got stronger until we left the ground. I smiled because i love that feeling. It reminds me of being in a high performance card with a lot of torque. I am not sure if we were heavy or in a hurry but it was a great way to go back to flying!

@terryofford4977 7 лет назад

Nice to hear such clear and decisive comments, very much appreciated, it also displays the huge differences between the Piston Engined a/c and the modern Pax Jets. Thank you Joe.

@LORESEP 7 лет назад

It has been a great help to my students at UTN in mexico city thank so m uch for your time and explanations

@pinkdispatcher 7 лет назад

Great and informative video, keep them coming. :) One tiny point: FLEX thrust will generally not save fuel; the lower fuel flow per unit time does not offset for the longer takeoff roll. In general, gas turbine engines are most efficient at higher power. If you don't want to do the complete calculations, the extreme point will give some hint that lower power is not always more fuel-efficient in total: there is a power setting too low to take off and fly at all, yet it will consume a non-zero amount of fuel. So the real main reasons for performing a "reduced-thrust takeoff" (to use a generic term) are reduced engine wear and (depending on the departure profile) reduced noise, although that's also less than you'd think because the climb gradient is lower with less thrust. That reducing mechanical wear is often more important than saving a bit of fuel is shown by the use of reverse thrust. Its main function is to reduce brake wear. Stopping must always be possible without them (except perhaps on ice), but they basically don't cause any wear.

@troybaxter2916 7 лет назад

Excellent video Joe. I've been an airline pilot for years but I still find myself watching your videos (and usually learning something new) so keep up the good work!

@enescakr4203 7 лет назад

i cant believe how much knowledge flying an airplane needs

@ethanwittenberg6172 7 лет назад

another great video Joe!

@flywithcaptainjoe 7 лет назад

Thanks Ethan :) Greetings Joe

@ikhlaassayeed8139 7 лет назад

joe please make a video on qualifications of a pilot and nessecities

@flywithcaptainjoe 7 лет назад

Coming up!

@marcus8036 7 лет назад

Was about to ask the same. will be looking forward to that video. Congrats on 100k

@tc1817 7 лет назад

Spelling "necessity" is one qualification.

@marklacy5011 7 лет назад

Joe, Can you explain what and how a side slip is performed? Is this a common practice in commercial aviation?

@cseblivestreaming 6 лет назад

Bad day?

@johnn2997 7 лет назад

Great channel - I'm glad I stumbled on this. I have always been fascinated with the mechanics of flying as opposed to the actual flying of aircraft. Thanks Captian Joe..you sure do make things a lot clearer.

@Gazshadows 6 лет назад

I have taken off from Lanzarote airport a couple of times and noticed what you said! And because we stayed not far from the airport so we could hear the planes take off, you can hear full thrust being applied straight away. Thanks for the information!

@nicolaslaing4053 7 лет назад

Thank you, Captain Joe! Thanks to you, I have decided I will become a pilot. My ATPL course will start in March 2018 (I couldn't start in September because I had to be 18 at the start of the course). Your videos have, for a part, really helped make my decision. It's not easy, it's not cheap, but damn is it awesome. I wish you all the best! Greetings from Belgium ;)

@flywithcaptainjoe 7 лет назад

Sounds great my friend, wishing you all the best for your career and it´s my pleasure if my video help you out here and there ;) Greetings Joe

@nicolaslaing4053 7 лет назад

Cpl and multi-engine training are integrated in the course, I'll be studying in Brussels (CAE Oxford Aviation Academy) and really have no idea yet which airline I'd like to join :)

@nicolaslaing4053 7 лет назад

Miam ga Thank you!

@rivsol Год назад

i hope u're doing good as a pilot now

@lukescott5938 7 лет назад

Joe how did you catch the 'Flying bug' and how did you go about training like picking a school and rasing the funds or did you get a airline to pay for you in return for working for them for X amount of years after passing

@ballajurassic9601 3 года назад

Thank you Captain! This is the best explanation of Flex that I have heard.

@christianbro2 7 лет назад

Thanks for your video, it is appreciated that you did it on a more complex topic.

@Nekkitus 7 лет назад

Thank you for a very informative video! I think it would be logical now to explain the thrust reduction and acceleration altitudes and (maybe) noise abatement procedures :)

@flywithcaptainjoe 7 лет назад

That´s true, but first the speeds video on V1 VR and V2 and then thrust reduction and acceleration altitude :)

@cppguy16 7 лет назад

I'm very curious about noise abatement takeoffs as well. I commonly experience it in Orange County, California (south of Los Angeles). It's a high acceleration, steep climb takeoff, followed by an abrupt reduction in power, in order to concentrate the noise to the airport. Further climbing is only allowed above the ocean. You can clearly feel and hear the difference even as a passenger. It feels almost as if you were about to land right after takeoff, obviously to reduce the noise over Newport Beach.

@Alexagrigorieff 7 лет назад

+cppguy16: SNA runway is also pretty short: about 5700 ft (while, for example, LAX runway is 12000 ft).

@cppguy16 7 лет назад

True, but normally airplanes climb steadily. At SNA, they climb at 25 degrees (10 degrees steeper than usual), then sharply reduce the power. They fly level all the way to the Pacific, then climb normally. It's the most fun airport in the US (or the scariest, depending on who you are). Flight attendants have to warn passengers so everyone is mentally prepared for this.

@oscarb9139 3 года назад

@@cppguy16 You are very correct. The normal thrust reduction/acceleration is 800 feet above the ground. In SNA the power is reduced above 1500 feet and acceleration is above 3000. Runway length has nothing to do with this. It is, as you suspected, a noise abatement procedure. SNA has noise sensors off the end of the runway. Too much noise can result in a fine, and enough violations can result in loss of authority to fly here. There is also a curfew. Here is an article. blog.aopa.org/aopa/2018/11/19/nadp-1-versus-nadp-2/

@jaimaansinghmonga3305 7 лет назад

Hi Captain Joe! Please explain SQUAWK...

@flywithcaptainjoe 7 лет назад

Coming up! Greetings Joe

@factsverse9957 7 лет назад

Captain Joe Your cheeks are so red....

@mr_nice. 7 лет назад

It's the transponder code. That's a very good idea. Why do they call it that? I allways wondered how they came up with that name.

@FanjitaUK2k8 7 лет назад

It was to do with the original British system in the war for friend/foe detection. It was codenamed "PARROT" and had the term squawk connected with it as a result which originally meant to cycle it I believe. In modern times is now associated with the 4 digit code assigned by ATC.

@rogervandecamp8950 7 лет назад

"It was to do with the original British system in the war for friend/foe detection." IFF Code: Information Friend or Foe

@rosen9425 7 лет назад

It becomes more and more amazing how flying these beastly machines is even possible

@dexopdencamp4901 7 лет назад

The more I watch... The more I understand everything... Great video again

@nilanjanbanik7509 7 лет назад

Thanks for the great video. What about the Noise Abatement Takeoff Procedures (NATP)? I used to think the reduction in engine power shortly after take off was due to NATP, i.e., flying over residential area.

@oscarb9139 3 года назад

It is actually NADP Noise Abatement Departure Procedure. Here is an article that may interest you. blog.aopa.org/aopa/2018/11/19/nadp-1-versus-nadp-2/

@JJ37_ 7 лет назад

Tolles video, die Frage hab ich mir schon sehr oft gestellt 😃 wie ist das eigentlich, wenn ein Passagier mal ins Cockpit möchte? (natürlich auf Boden), ist das grundsätzlich erlaubt? Weiter so mit den (sehr hilfreichen) lernvideos :)

@robinfist 7 лет назад

One of the best explanations I have heard. WELL DONE, very very good!

@19TheChaosWarrior79 7 лет назад

Captain Joe another well explained video. I have absolutely no need to know any of this but I love watching videos like this. Well explained by someone who has a passion for what they do.

@mrtommygunwhite 7 лет назад

Joe been watching a lot of air crash investigation and I was going to ask could you explain "coffin corner" as I think it would make a good video

@dash8465 4 года назад

It's definitely a intersting and worthy subject, although the speed ranges have typically widened quite a lot in modern aircraft with greatly improved aerodynamics, sensors, and PFD's with clear and accurate dynamic speed limits displayed... and if violated today's aircraft respond much more tamely, most notably with regard to what part of the wing will stall first.

@oscarb9139 3 года назад

The coffin corner is slang for when the low speed and high speed symbols are very close together and is usually at a very high altitude. The airspeed indicator in this aircraft has a red band for the high speed limit and a yellow band for the low speed symbol. Go look it up on the web as my description is poor. At low altitude, the range between going to slow and too fast can be over 150 knots apart. But as the aircraft climbs they get closer together. Example: at sea level, Vls (low speed symbol) might be around 200 knots and Vmo is 350 knots. That same airplane at 39,000 feet might be Vls 230 knots and Vmo/Mmo 270 knots.

@surf2888 7 лет назад

can you make a video about the priority left, priority right for airbus

@irockusucks 7 лет назад

I'm sorry but I think it is 40 seconds to latch the system. that is for the airbus 320

@irockusucks 7 лет назад

I do think it's a bit long but it makes sense to ensure that no accidental takeover happens

@sebastianbaltazar8213 5 лет назад

Thank you Joe! I have the atpl performance exam very soon, you have helped so much!

@basilsunny6809 6 лет назад

you always explain well clearly,so that we can catch easily.Hats off captain

@n_g7009 7 лет назад

Kannst du als 100.000 Abo Spezial einen Flug von dir Filmen? p.s interessantes Video wie immer! ;)

@christofferwaltersdorff4303 7 лет назад

Hey Joe could you please do a video on the RAT?

@flywithcaptainjoe 7 лет назад

Coming out in two weeks, video is already finished!

@nazimfazilmohamedhanifa9733 7 лет назад

HI Capt Joe , Please explain about different types of altitudes including thrust reduction altitude and acceleration altitude

@oscarb9139 3 года назад

@@nazimfazilmohamedhanifa9733 On a takeoff, the power is applied (full power or reduced). This power is maintained until thrust reduction altitude, when the FMA flashes to indicate it is time to pull the thrust levers back into the climb detent (climb thrust is set). Acceleration altitude is when the pitch FMA (pitch controls airspeed) changes from SRS to CLB or OPN CLB and the flight director commands a lower pitch so the aircraft can accelerate and allow to pilots to retract the flaps on schedule at F speed and S speed (that’s Airbus stuff).In this video, at 1:50, you can see that the FMGC (flight management and guidance computer) is programmed to do both at 1500’ above sea level, not ground level. Ok,I just finished packing to fly out tomorrow and I can add to this comment. It appears that Cap’n Joes company uses a 1500 foot thrust reduction and acceleration altitude (I don’t know the field elevation of the airport he entered and I don’t want to leave this comment to go watch the video so I can google it). So, when he takes off, he pushes the thrust levers up to the TOGA or FLX detent and the FADECs will set the proper power for the takeoff. At 1500’ above sea level, the FMA (annunciation in the upper left of his PFD) will change from MAN TOGA or MAN FLX into a flashing LVR CLB in row 2. This is the signal to move the thrust lever back from the takeoff setting to the Climb Detent (two clicks back from TOGA or one from FLX/MCT) and this is the way the pilot communicates to the FADECs that climb power is desired. The pitch bar will move to a lower position on the PFD to command the pilot or autopilot to lower the nose and accelerate. If the flaps were set at “2” or “3”, the pilot will see an “F” on the speed tape (airspeed tape) and once the aircraft is faster than that, the flaps are retracted to the 1 position. Once the flap handle is moved, the F disappears and an S appears on the speed tape. When the aircraft is faster than S speed, the flaps are retracted to the up position and the aircraft will accelerate to 250 knots until 10,000 feet and then will accelerate to “economy climb speed” which is some number that is affected by wind, gross weight, and cost index. Time for dinner. I may add more later.

@Rasmorak 7 лет назад

What a wonderful channel! Thanks for all your hard work, and for sharing your knowledge with us Joe! I'm trying my hardest to end up in one of those two seats in the cockpit!

@martinsivc5769 7 лет назад

Hey Joe! Thanks for helping me out with every video you have. Everything helped me so much, I want to be a pilot when i grow up.

@PPC4 7 лет назад

I'm a little confused. If a higher flex temperature means an assumed higher outside ambient temperature why does that result in a lower power setting when you then say you would use the toga setting in hot or high conditions. Would not a higher assumed ambient temperature mean that more power is given not less (thinking thinner air). Or is it relating to a higher acceleration rate meaning you have more room for a rejected takeoff meaning you can take off at a higher airspeed?

5 лет назад

I am sorry I answer to you one year later but as I understood on the video, the higher outside ambiant temperature is harmfull for the engine temperatures, therefore the computer reduces the power of the engines (through a savant calculation) to limit the engine temperatures. Maybe I am wrong of course but I suppose the problem with thin air is less a problem than the problem of engine overheating.

@Rhythmmical 5 лет назад

Hotter air is less dense I think, so you will need more thrust to get to a good liftoff speed. Now this is probably only in the instances mentioned in the video, such as a higher runway attitude or short runway. When you have more dense air due to lower runway altitude, and/or longer runway, you can use lower thrust in a higher air temperature to save on engine life. I don't think I fully understood your question, but tried answering it the best I could. This is my understanding based on this video.

@shaunweatherill6651 5 лет назад

The method wasn't completely explained in the video, every airline and aircraft manufacturer has slightly different methods of achieving similar outcomes. There are 2 power settings we calculate for takeoff, the first being rated power (TOGA power) - this factors actual ambient conditions to give us an engine power setting that should not exceed engine temperature limitations should we need to use it, then from rated power we can use the assumed temperature method (or FLEX) to reduce the rated power to what was explained in the video. Like Joe said, there are circumstances that prohibit us from using reduced power and to use rated power instead (bear in mind rated power may not be full power, rated power is max available power that when calculated properly should not exceed engine limitations, even when the ambient temperature is hot).

@Airblader 5 лет назад

@@shaunweatherill6651 Could you also explain why a "fake" temperature is used as the unit in the first place, and more so with such unrealistic values as ~60°C? It sounds weird to use completely faked numbers rather than inputting factual information.

@gardemeister 4 года назад

İt is a reference temperature to TOGA performance . İf outside air temp was 58 C TOGA would does exactly same performance . That means reduction in performance as air gets hot. By that logic flex 48 C will give more performance than 58C .

@mds3697 7 лет назад

Hey Joe, can you explain the difference between ground speed and airspeed? why is the airspeed displayed on the speedometer usually much lower than the actual speed in mach or kilometers/hour? to give an example: I play a flight simulator sometimes and in a 737 the average cruise speed that's displayed on the speedometer is about 320 knots. but when you google 'boeing 737 cruise speed' all answers will be around 500 knots. Why is there such a big difference sometimes?

@flywithcaptainjoe 7 лет назад

That´s a great question, I will look in to that for you! Greetings Joe

@SidneyKenson 7 лет назад

The IAS only refers to the static pressure of the air, regardless of temperatures or air pressure through altitude. Then you have the TAS, where all these influences are calculated in, and finally adding the wind gives you the GS. Therefore I had a GS of 575kt at about 300kt IAS. Thank you, backwind of 85kt on FL340...

@bmanna495 7 лет назад

the ground speed is calculated by the GPS in relation to the position with the ground, the airspeed is calculated by the pitot tube that reads the difference between static air pressure and dynamic pressure(the pressure that the air makes hitting the plane with a certain speed) and calculates the speed using the bernoulli equation. Since the static air pressure is much lower at cruise altitudes the readings are low but that doesn't mean that it's useless because that is the speed that is used for the aerodynamic calculations like stall speed and overspeed corner

@EinkOLED 7 лет назад

Midas The higher you climb the thinner the air becomes, meaning the pitot tube receives less air, indicating less air speed. If there is a 50 knot heading then this is also added in the indicated air speed, a 50 knot tail would be subtracted (hence why it is important to takeoff into the wind). The aircraft requires indicated air speed in order to fly (stall speed, over speed/flap speed, landing/takeoff speed) etc, etc.

@blumac9801 7 лет назад

Midas the higher you are the bigger the world is pretty much...

@julioklemba9093 7 лет назад

Nice video Joe! Almost 100.000 subscribers! Congratulations

@aarondowden4244 7 лет назад

Thank you so much for this explanation!! I have to say your videos are really helpful and informative, keep it up Joe!

@Nilguiri 7 лет назад

Hi Joe Do you have any videos explaining the v1 v2 and rotate speeds? And TOGA? Thanks

@randolphclarke4674 6 лет назад

Nilguiri I think V1 means the plane has to lift off the ground and it’s too late to abort takeoff

@PenguinYeet 6 лет назад

V1 Is the point where takeoff should not be aborted.

@mwr._.306 5 лет назад

V1: take off can't be aborted Vr: the speed where the pilot has to rotate the aircraft V2: The speed where the aircraft can continue it's climb with no problem even in case of an engine failure

@lucasbrien5008 5 лет назад

TO/GA is the speed for Take Off/ Go Around

@dpm-jt8rj 5 лет назад

@@lucasbrien5008 There is a PilotsEYE.tv video of a LX A330 flight ZRH - MIA and the FO stated that their flight would be a TOGA take off from ZRH. When would a flight have a TOGA take off and when would a flight not be a TOGA take off? It's has to be an Airbus thing.

@rubenkorkis282 7 лет назад

Joe, can you make a video about engine failure? what happens, does it crash immediately or can you glide it safely to the ground?

@onflightsim32 7 лет назад

ruben korkis you can glide safely back to the airport and with one engine you can still fly good with those commercial airplanes

@flywithcaptainjoe 7 лет назад

Planes don´t immediatley crash due to an engine failure, I`ll see what I can do! Greetings Joe

@rubenkorkis282 7 лет назад

Captain Joe thanks, looking forward to it

@EdekaKuchen 7 лет назад

Captain Joe kannst du mir Webseiten zeigen wo man zum Beispiel flightstick oder Navigationsgerät für einen Flugsimulator kaufen kann

@onflightsim32 7 лет назад

Marc Kupper Google?

@halcyondaystunes 7 лет назад

Brilliant and informative video as always Joe.

@nathanrichardson8912 7 лет назад

I love learning this stuff, thanks Joe✈

@rubenrocha9 7 лет назад

Hi! I just learn so much from your videos. I want to become a pilot so I'm better paying attention. CAP CAN YOU EXPLAIN WHAT DOES "MORA" mean? Thanks a lot. Ruben

@flywithcaptainjoe 7 лет назад

Yes, I´m on it !

@rubenrocha9 7 лет назад

Thanks a lot! I'm Portuguese. have you ever flown to Lisbon? what about the approach? what's the best app for you?

@Brukn0ws 7 лет назад

Madeira!!!

@PeterGamerTutoriais 7 лет назад

Açores

@rubenrocha9 7 лет назад

MalucoHD #ConTV que ilha?

@jasperstevens8270 7 лет назад

I've a question for a video, what is the little red buttom on the thrustlevers

@onflightsim32 7 лет назад

Jasper Stevens you can push that in order to switch the autothrust off

@jasperstevens8270 7 лет назад

OnFlightSim thank you but what is the autothrust is that the autopilot?

@onflightsim32 7 лет назад

Jasper Stevens it controls the engine thrust so you could say it's an autopilot for the engines

@jasperstevens8270 7 лет назад

OnFlightSim Ok thank you!!

@alexxd_1252 7 лет назад

Good Question! As far as i know it is pushed when you discontinue your approach and go around and gives you max power as well as pulling up automatically

@uyhu24 7 лет назад

Awesome video joe. Loving this channel

@flyworldwide8961 7 лет назад

Thank you, this was one of the best explanation on flex temp. Thanks again

@micha0001 7 лет назад

58° Celsius??? Has Death Valley an airport??

@hvnterblack 4 года назад

isn't it Fahrenheit? it is 14,4 C

@oscarb9139 3 года назад

@Alaukikdeep S Boparai you are correct. Entering a higher than actual temperature into the Takeoff Perf Page causes the FADEC to calculate a lower power setting for takeoff.

@Jess-kd8cl 7 лет назад

Neat vid first

@joelfiction 7 лет назад

I find your videos very interesting and informative and are just the right length to watch while on break. Keep up to good work captain :)

@GastonDwarvenPilot 2 года назад

I arrived a couple of years later, but still very useful explanation Joe. As always, thank you for sharing!

@siddhantparekh8007 7 лет назад

When the engines are starting up, why can both engines not be started at the same time?

@flywithcaptainjoe 7 лет назад

Try blowing up two ballons at same time, won´t work due to lack of pressure! Greetings Joe

@siddhantparekh8007 7 лет назад

Thanks!

@StephenKarl_Integral 7 лет назад

Some russian (ukrainian in fact) airplanes can. But you don't want to mess up in case you have trouble with one engine on startup. Just do it one after the other...

@donnyguns1 7 лет назад

if you have four engines, you can put the first one on reverse then cross bleed to start next two together. We do that on C17s

@martinthor4000 7 лет назад

to talk about the 787 which does start both engines at once :P

@gowthamnaidu3029 7 лет назад

Hi joe....how to become a pilot of Qatar airways or anything...plzz reply

@cheburatorish 6 лет назад

Not possible, forget it. At least, not in this decade.

@mgtowacademy8433 7 лет назад

Almost to 100k subscribers joe! Been here since about 2k! Love your channel keep up the good work!

@chrismcclellan8539 7 лет назад

I really enjoy your videos. You do a great job explaining details!

@CameronWilbraham 6 лет назад

I love how something so important is done by cheating a system! 😂

@oscarb9139 3 года назад

It isn’t cheating the system. It is just giving the system a number to make a calculation for a thrust reduction. Boeing does the same thing, but they call it the “assumed” temperature. If it was tricking the system, pilots would give the false temperature on the INIT A page instead of the outside air temperature.

@petemichel8011 6 лет назад

Vielen Dank Joe, das du es unter dem Video auf Deutsch erklärst...Happy flying all the time;-)

@12secyellow98 7 лет назад

Great video Joe, and really helped explain what I feel on takeoff in an Airbus vs. Boeing. I've often wondered why the 737 actually starts accelerating during the climb at times.

@patryk7916 7 лет назад

nearly 100.000 subs! good job captain👨🏼‍✈

@xavierlarvor201 5 лет назад

Very clear explanation, Joe, thanks!

@sonheromayor 2 года назад

Thanks Joe for all these good explenations ! It is very useful for my ATPL :)

@GouveaFlightSim 7 лет назад

I always wondered to know more about this procedure. Thanks for the great explanation.

@FlexCrush1981 7 лет назад

Thanks for taking the time to make this video Joe

@flywithcaptainjoe 7 лет назад

My pleasure Robbie!

@bayguy69 7 лет назад

Love your videos!. Keep your good work!

@VincenzoMaxpower 7 лет назад

Very informative as usual. Thank you Capt. Joe

@Sebastian-ze2oq 7 лет назад

Dear Captain Joe, thank you very much for another informative video. I have always been confused about flex temperatures & derating, but this has really helped me get my head around it. If you find yourself in the UK and fancy a tour around an engine manufacturer's base then let me know.

@JonOlaivar 7 лет назад

I was on an a320 recently from LAX to Denver and the climb was insane! I didn't hear the engines back down after take off- which caught me by surprise.

@AgnostosGnostos 7 лет назад

Dear Captain Joe you have just reached 100.000 subscribers in a very short time. Congratulations! I am waiting for the a video with the honorary silver play button that RU-vid will send you. Keep on the good work. I have learned a lot from you and I am aware about many things during my flights. Again thank you.

@muhammedhaneef1798 6 лет назад

U have a grt prsnlty.... We fellow curious students love to learn from you... You are so patient and calm..... Thnx a lottttt......

@DinizFreddie 7 лет назад

Wow. That was very interesting! Thanks, Cap!

@adithyasrinivasan4320 6 лет назад

Hi Joe., Its a great video explaining the basic concepts in the airplane operation. As an engineering professional, we do design the systems considering similar parameters and its impact while gas is being handled. I could notice the similarities which are well explained and demonstrated through this video. Thanks Joe.. for your efforts and the video.

@steveemerson4120 7 лет назад

Great video as always and stylish presentation.

@mohammadbazzi9759 6 лет назад

Thank you so much captain. I enjoy all your videos. I'm very curious about airplanes and how they works and you give me all the information. I thank you so much for doing this for us. God bless you and bless your family. greatly appreciated your work Capitan. I'm from Windsor Ontario canada.

@YelpBullhorn 6 лет назад

Love Captain Joe's videos. Enjoyed this one too. Very interesting -- even though I've no idea what he was going on about!

@Rubberdinghyrapids 7 лет назад

thank you captain joe, for a fantastic video, and an amazing channel. I really appreciate the effort and time you put in to creating these factual and formal videos. just outstanding. thank you and kind regards kieren

@KEITHGEE1000 7 лет назад

Really interesting, especially for those of us into Flight Simulation. Many thanks!!

@gustavodeibarra3879 7 лет назад

Great video´s Cap Joe. Congratulations. Good Flight´s , Gus.

@rodneywhitfield5754 7 лет назад

Captain Joe, as a Spartan School of Aeronautics, back when it was still a Aeronautical School of merit before they were bought out by NEC schools, I was a Instrument technician, I would like to Thank you for bringing these questions forth and answering them! 😄

@elliotdebruyn4390 6 лет назад

Thank you so much! I was confused on the FLEX TO TEMP part of the PERF on the A320 :)

@MrThuggery 7 лет назад

I really enjoyed that thanks Capt Joe!

@INTERSTATEREMOVALISTSAUSTRALIA 7 лет назад

Great information and very clear, thanks very much i'll keep watching

@CrisURace 7 лет назад

Awesome, i love flying!!

@Sjjones1977 7 лет назад

Thank you Captain Joe for this video. It is as always very interesting and informative. Looking forward to your next video.

@JayDS509 5 лет назад

Hi Capt. Joe...Thanks for the consistently clear, engaging and often humorous presentations of aviation topics. I wonder if you would be willing to do a series on emergency procedures for pilots. These could be by cause (e.g. engine out, etc) or by circumstance (e.g. reject takeoff, etc.). Thanks again for the great vids!!!

@traviswalker6831 5 лет назад

Great video's! Good information for a pilot transitioning to jets!

@danieleygin1179 7 лет назад

Great video Captain! continue to make more videos and GOOD LUCK!!!!! :)

@hainguyen6514 7 лет назад

stumbled on your channel while doing some research about the Concorde. Great channel, never thought aviation could be this interesting. :D

@Wackans 7 лет назад

I liked all those videos ! Short videos that helps a lot to understand the Airbus world

@NeilVanceNeilVance 7 лет назад

One of his best!!

@scubthebub 7 лет назад

Nice video and very well explained. I always enjoy learning about new things I didn't know existed :)

@dickverburg1430 7 лет назад

Thank you Cpt Joe ! very clear

@robertmurphy1066 3 года назад

Great explanation. Thanks Joe 👌🏼

@flightisallright 7 лет назад

Wow, much respect for such a great explanation.

@gooner72 3 года назад

Great video mate!!!

@MrFlightSimulation 6 лет назад

You are the best!Thank you very much cpt Joe!!!

@gjmalek5074 7 лет назад

Hey Cap. Joe its amazing to see you every time on this channel !!! every video is very informative and exciting and its totally changing the way we travel in plane and we can say i know the reason behind .😀😀