What is Totem pole MOSFET gate driver? Totem pole MOSFET gate driver working | Push pull gate driver

Подписаться 60 тыс.

Просмотров 85 тыс.

50% 1

#foolishengineer #MOSFETdriver #gatedriver
There is a mistake in MOSFET based totem pole circuit. The P channel is supposed to be upside down. Please go through reference documents for accurate circuit.
0:00 Skip Intro
00:24 WHY Totem pole driver?
01:43 Totem pole circuit
03:27 Totem pole circuit working
04:58 Advantages
06:00 BJT based totem pole circuit disadvantage
06:15 MOSFET based totem pole circuit
07:24 conclusion
References:
- www.ti.com/lit/ml/slua618a/sl...
- www.diodes.com/assets/App-Not...
- www.ti.com/lit/an/slua877/slu...
More Videos:
Videos on MOSFET Drivers:
MOSFET driver 3 - • What is MOSFET gate dr...
MOSFET driver 2 - • Why do we need gate Re...
MOSFET driver 1 - • What are MOSFET gate d...
Videos on MOSFET:
MOSFET Avalanche Ruggedness - • MOSFET Avalanche Rugge...
MOSFET Avalanche Breakdown - • What is Avalanche brea...
MOSFET Inductive switching - • MOSFET switching wavef...
MOSFET & Inductor - • MOSFET switching for a...
MOSFET SOA - • What is SOA of the MOS...
MOSFET switching - • How MOSFET switching w...
Parameters of a MOSFET - • How to select a MOSFET...
Basics of MOSFET - • Difference Between MOS...
Videos on BJT:
PNP BJT as a OV protection - • How to design PNP BJT ...
NPN BJT as a OV protection - • How to design NPN BJT ...
PNP BJT as a Switch - • How to use BJT as a sw...
NPN BJT as a Switch - • How to use BJT as a sw...
Basics of BJT - • How BJTs Work? | How T...
CCCV Charging:
Part 2 - • CCCV Battery Charging ...
Part 1 - • How does a Battery Cha...
Current Regulators:
CCC with op amp &BJT - • Constant Current Regul...
CCR with BJT & TL431 - • Constant Current Regul...
CCR with BJTs - • Constant Current Regul...
CCR with Zener diode & BJT - • Constant Current Regul...
CCR with LM317 - • Constant Current Regul...
Power Supplies:
Voltage regulator using transistor - • Voltage Regulator usin...
Full Bridge Converter - • How does a Full Bridge...
Half Bridge Converter - • How does a Half Bridge...
Zeta Converter - • How does a Zeta conver...
Cuk Converter - • How does a Cuk convert...
Buck-boost converter - • How does a Buck Boost ...
Double Ended Forward converter - • Double Ended Forward C...
Active Clamp Forward Converter - • Active Clamp Forward C...
Forward Converter - • How does a Forward con...
SEPIC converter part 2 - • SEPIC converter design...
SEPIC converter part 1 - • SEPIC converter design...
Flyback converter part 2 - • Flyback converter desi...
Flyback converter part 1 - • Flyback converter desi...
Push-pull converter part 2 - • How to design a Push p...
Push-pull converter part 1 - • How to design a Push p...
Boost converter design - • How to design a Boost ...
Buck converter design - • How to design a Buck C...
SMPS basics - • Basics of Switch Mode ...
Embedded Systems:
SPI Communication Part 3: • Advantages & Disadvant...
SPI Communication Part 2: • SPI communication Data...
SPI Communication Part 1: • Basics of SPI communic...
I2C Communication Part 3: • Advantages & Disadvant...
I2C Communication Part 2: • I2C Frame structure Un...
I2C Communication Part 1: • Basics of I2C communic...
UART Communication Part 2: • Understanding UART Com...
UART Communication Part 1: • Basics of UART Communi...
Basics of Communication: • Communication protocol...
Power Electronics:
Power Factor Correction - • Power Factor Correctio...
Power Factor - • What is Power Factor |...
Electric Vehicles:
Battery management system 2 : • How does a BMS (Batter...
Battery management system 1 : • What is a Battery Mana...
Battery basics part 4 : • Electric Vehicle batte...
Battery basics part 3 : • What are the types of ...
Battery basics part 2 : • What is SOC, SOH, SOP,...
Battery basics part 1 : • Which Battery is used ...
EV motor controllers part 2: • Motor Controllers in E...
EV motor controllers part 1: • Motor Controllers in E...
Charging of EVs: • Working of Electric Ve...
EV basics: • How does an Electric V...
EV parameters: • What is inside the Ele...
EV Motors: • Motors used in electri...
---------------------------------------------------------------------------
Check us out!
Facebook - / foolishengineer-407598...
Instagram - / foolish_engineer
Twitter - / foolisher25
Subscribe now for more videos like this!

Наука

Опубликовано:

25 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 88

@FoolishEngineer 2 года назад

There is a mistake in MOSFET based totem pole circuit. The P channel is supposed to be upside down. Please go through reference documents for accurate circuit.

@user-gf3xl6ez2w 2 года назад

also mosfet totem pole need RD circuit in gate for different Ton & Toff times.else driver will produce a lot of heat

@VS-qs7fn Год назад

Made total sense to me. Well explained sir.

@AlejandroEirea 2 года назад

Great video. This type of videos is very useful for me.

@FoolishEngineer 2 года назад

Thank you so much for watching!! Please don't forget to subscribe to our channel

@felipeteixeiraroberto7869 Год назад

Thanks from Brazil, great video.

@jimedgar6789 2 года назад

Excellent instruction once again.

@FoolishEngineer 2 года назад

Thank you so much for watching!! Please don't forget to subscribe to our channel

@davidsussens4478 6 месяцев назад

Great video! Thank you.

@brianstelter7067 2 года назад

Actually the gate of the power fet should have back to back zener diodes apx. 18 volts. As a MOSFET the Miller effect will show large transients at the gate when driving large currents, these can damage the drive circuitry.

@sebapolsebapol4927 2 года назад

Sir well done for your job you have done so far. Could please make a video about smps control loop stability and emphasizr on rhpz please

@FoolishEngineer 2 года назад

will work on it, please don't call me sir!

@JLCPCB 2 года назад

Great video! 😀

@FoolishEngineer 2 года назад

Thank you so much for watching!! Please don't forget to subscribe to our channel

@danielugwa6517 Год назад

Thanks for the teaching. one more sir what can be the reason of overheating on mosfet even when it been operated with totten pole to drive the mosfet on smps ur help sir. again I want to know how I can add 12v in gate drive transformer please I need the transformer coiling circuit diagram thanks

@xiangli9639 Год назад

Are Vdd and Vbias the same value？The smoothing transistor between the two bypass capacitor might conduct some current if Vdd and Vbias are not the same, am I right?

@rameshwarshelke4633 2 года назад

Very helpful ☺️🙏

@FoolishEngineer 2 года назад

Thank you so much for watching!! Please don't forget to subscribe to our channel

@JustAnotherAlchemist Год назад

This information was taken almost verbatim from Texas Instruments application note SLUA618A, section 10: Bipolar Totem-Pole MOSFET Driver. Edit: I see now that you reference this in your description, making my point moot.

@user-gf3xl6ez2w 2 месяца назад

For BJT totem pole Vcc is correct name of supply voltage,c-collector.Vdd for mosfets.For correct work of mosfet totem pole RD circuit in gate supply needed for different rise/fall times to prevent shoot through

@powerelectronicsentertainn3997 4 месяца назад

Good video... But one issue is that, while replacing with complimentary MOSFET irrespective of gate supply for the totem circuit the upper MOSFET will be conducted through its parasitic diode...

@jensschroder8214 2 года назад

6:40 The drain and source of Q1 are reversed. The body diode makes a big short circuit.

@FoolishEngineer 2 года назад

Sorry for that! please check description

@deejayobenn160 4 месяца назад

What are the best bjt for totem pole to switch gate faster with good current

@Spiderman-sr7pj 3 месяца назад

what is the switching frequency limit fo this circuit if bjt is used?

@samuelyesuvadianj9946 6 дней назад

You'll notice in the push pull stage that you need a PNP and an NPN transistor, whereas the totem pole driver uses only NPN transistors

@arunanindian40 Год назад

Highside mosfet of totempole has body diode in downward direction it means even if the mosfet is off the diode conducts

@Charlyx2009 10 месяцев назад

Should they be igbt? Good video.

@stuarticusrobinson9319 Месяц назад

Would vdd not be lower than 10v due to the diodes forward voltage drop?

@cesarjorgemurillobarientos1813 2 года назад

Very good master

@FoolishEngineer 2 года назад

Thank you so much for watching!! Please don't forget to subscribe to our channel

@GianniLaschi 2 года назад

There Is some problem with the High side mosfet, the internal diode as shown in the schematics Will conduct Always to the gate of the Power mosfet

@FoolishEngineer 2 года назад

Oh No!!! There is big mistake in my video. The P channel is supposed to be upside down. I am blurring the MOSFET part for the future references. Thank you so much for highlighting this mistake!!

@ehimwenmataiwolouis1388 2 года назад

Thank you very much, can I use it in ic555 output?

@jaydeepsejpal1427 Год назад

yes you can use the 555

@alexlo7708 2 года назад

I think inductor on far right is toroid with ferrite core, isn't it.

@benjaminvangheluwe3079 5 месяцев назад

Does a totem pole provide for a higher rise & fall time of the gate pulse? Or is it only the fall time that would be quicker? Thank you, Benjamin.

@egg99 4 месяца назад

both will be quicker

@didithartanto4651 5 месяцев назад

very2 excellent

@jasonwee7580 7 месяцев назад

Could you just replace the totem pole with a single BJT NPN? What is the benefit of having the totem pole (made up of BJT) over a single BJT?

@satasauu757 Год назад

How can we make the gate pin negative 9 volts while the MOSFET stops conducting electricity? Help me make a video thank you.

@LEO22116 Год назад

You can use a voltage divider circuit. For eg. total supply is 24V, you can add two resistors (and Zener diodes) to get 18V and -8V.

@carlosmf6954 6 месяцев назад

👌

@Dc_tech386 2 года назад

I use this today’s and the 15 voltage to the totem pole blow my gate on mosfet I did this same design and it keeps blowing my mosfet hat I don’t understand why my data sheet said only 5 volt to gate so should I use only 5 volt to driver

@FoolishEngineer 2 года назад

Yes, please use only 5V if the datasheet mentions the same

@kensmechanicalaffair Год назад

Using a gate resistor?

@BLOCKsignallingUK 10 месяцев назад

Need a 5V zener on the gate to ground to clamp the voltage

@mithunsaha9456 4 месяца назад

❤❤❤Sir q2 transistor change input diod no working

@panditji8823 Год назад

Hi, I'm novice in electrnics pls can you help to understand how to read schematic.

@Coolgiy67 10 месяцев назад

Go get a electrical engineering degree or you can just take a circuits class and electronics 1 class (with appropriate math backgrounds) and you will be able to understand any schematic

@ChickenPermissionOG Год назад

Wouldn't using mosfets as todem defeat the protection of the bjts?

@jaydeepsejpal1427 Год назад

yes you can but again it will be a complicated and not cost effective

@gregorymirsky8707 2 года назад

What is shown is not a totem pole. A totem pole is based on transistors of the same type of conductivity. It is a very bad usage of a complimentary power amplifier.

@steve_ancell 2 года назад

Great, but why's it called a Totem pole?

@swedensy Год назад

Has anyone figure out yet how circulation pump motor works? I know it uses gate driver in IC to drive gates in IGBT. It is 3 phase too. pump name Wilo made in sweden or something. Same shit is in those compressor heater/cooler, the fans are run by PMM thats driven by weird pwm using gate drivers and IGBT. I wan to make them run on 12 or 24v DC. Any smart person here? I could even pay if you know where to tap the pcb.

@Sekhar_Home Год назад

Could u pls tell why Q1 is required

@panzerkampfwagen161 Год назад

I think Q1 is there to provide enough charge to the MOSFET gate for turning it on fast

@Sekhar_Home Год назад

@@panzerkampfwagen161Yes, thank you

@subash001s Год назад

Sir can you please do it on practical so that we can make it and take it on real life

@FoolishEngineer Год назад

I don't have lab setup as of now to do the hands on! will surely work in future

@nikolaivic4480 2 года назад

What if VDD>Vbias is required?

@codures 2 года назад

Well, you add a parallel resistor to Q2 (the Emitter-Collector section).

@nikolaivic4480 2 года назад

@@codures How is that gonna charge the gate to VDD and not to Vbias only?

@codures 2 года назад

@@nikolaivic4480 well, while the gate voltage won't under any circumstances exceed vbias - 0.6v, it'll definitely help to keep the mos OFF. If you wanna make the mos gate reach vdd (or higher), you might wanna change the driving system (or going for bootstrap caps respectively). This drivers are good for logic gate MOSFETs, hence the need to keep the gate always low. Edit: if that resistor is large enough (given Q1's hfe, you may even put that BJT in deep-saturation, hence reaching VDD - 0.3V, but again, not VDD.

@nikolaivic4480 2 года назад

@@codures Vbias is 3v3 or 5v if it is a uC. VDD should be 10V for normal level FET to reach lowest Rdson. Emitter follower is not a good solution in that case, maybe for logic level FETs. Common emitter topology is better.

@codures 2 года назад

@@nikolaivic4480 totem hater, lol.

@kamleshchavan7451 Год назад

Please remake the video with accurate circuit

@rmjnm Год назад

Sub titles is bloody hell.

@preston963 2 года назад

All that is is a push-pull driver for a MOSFET which is basic common knowledge dating back to the 1950's & earlier in valve audio amps the only difference is there's no biasing between the bases as its logic!

@jimedgar6789 2 года назад

Dude, I was not alive in the 50s. So good knowledge, well presented.

@jimedgar6789 2 года назад

Don't be a hater, boomer.

@preston963 2 года назад

@@jimedgar6789 Fun that I wasn't alive till the mid 60's but it still common knowledge & I'm not a hater or a DUDE!... I'm a bloke with vast electronics knowledge!

@jimedgar6789 2 года назад

@@preston963 I dig it. But still nice to be taught the old stuff. Not every knows it. Like Ohm's law. when you get it, you really understand more than you ever did. I am learning new stuff every day and have been doing this for three decades :)

@jerrynaslund3368 2 года назад

Please work on your english. Video is fantastic though.

@FoolishEngineer 2 года назад

okay

@RainLovesCobain Год назад

there is nothing wrong with his english

@LEO22116 Год назад

His English is way better than your attitude.

@JesusRoseAgain 2 года назад

Haha wtf

@stevenbliss989 2 месяца назад

How can you avoid the HIGH current flowing in Q1/Q2 when transitioning?

@chasidgoodmaker1804 Год назад

Pwm doesn’t have minus low pulses only high and zero so how it can open pnp bjt?

@Coolgiy67 10 месяцев назад

Pnp bjts and PMOS transistors are both conduct current when you apply 0 volts to the base/ gate. This is opposite of npn or NMOS trasistors that only conduct current when succificent voltage is applied at base/gate

@oakspines7171 6 месяцев назад

You are correct. However, it works when the gate of the next FET circuit is charged up close to VDD. It looks like the pnp Q2 when turned on with its emitter at near VDD, it would be in Saturation condition, then goes into Active as VDD drops, then turing OFF as VDD approaching 0 + VBEon. Similarly for top npn Q1. So iniitally when the controller send out a 0v low and the output is at 0v, Q1 does not work and the circuit does nothing. However, when the controller output goes H, Q1 would work and charge the output to VDD - VCEsat. And it works from there on. Some initial voltage at the output of the totem pole circuit in between could cause the initial half of the PWM L or H from the controller not to work intiialy, but the next half of the PWM of the opposite value would work and charge or discharge the output to the operating levels the BJTs citcuit needs - as explained above. Is this correct, the author ?

@oakspines7171 6 месяцев назад

The PMOS in the circuit is upside down, and when corrected, its body is connected to VDD. When PWM output is say 0V at the gate of the PMOS, a channel is formed under the SiO2 of the gate and the PMOS is on. Similarly for the NMOS below, the body is connected to GND 0V, when you put in something above the VGS threshold, VDD or not neccesarily VDD but just above VGS threshold, then similarly to the PMOS above, a channel is formed an the NMOS turned on and discharge the output of the CMOS circuit. If for experiment, if you can connect NMOS body to VDD by reverse the D-S, it will not work when PWM is VDD but will turn on when PWM is 0v which both PMOS and NMOS are on. BJT on and off conditions are different as explained in the other reply here.

@oakspines7171 6 месяцев назад

For th elast sentence of the long 2nd paragraph, the other problem when connected the MOSFET in reverse is that it will be on in the reverse logic due to the body diodes are reverse.