Тёмный

Why build an FPV drone when GEPRC Mark 5 is this good? 

Joshua Bardwell
Подписаться 331 тыс.
Просмотров 200 тыс.
50% 1

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the GEPRC Mark 5 at:
* RaceDayQuads - bit.ly/3vEUQ1f
* Banggood - bit.ly/3sXCSHe
* GEPRC - bit.ly/3OuAy38
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
-- TABLE OF CONTENTS --
0:00 - 5" BnF are really freaking good these days
2:52 - Strong, well-designed aluminum front end
5:25 - Split top-deck design, but done right!
6:35 - The same high-low bottom plate design as Apex
7:17 - How are the arms attached
8:38 - Arms are 5mm carbon by 10mm thick and are well designed
9:51 - Hardware is 10-9 steel
10:42 - FC and ESC are both soft mounted and wires are neatly run
11:12 - Three variants: DJI Air Unit, Vista, and analog
11:23 - I hate the plastic motor wire protectors
13:03 - Why did they use a 2107.5 sized motor?
• The most important spe... - In-depth discussion about how I evaluate motor sizes
16:16 - FC and ESC close look
17:56 - Flight testing
20:50 - Let's compare: GEPRC Mark 5, Diatone Roma F5 V2, and iFlight Evoque F5
21:46 - These things are the same no matter which version you get
22:38 - Evoque has 20mm FC and ESC; others have 30mm
23:21 - Evoque is the heaviest of the three. Diatone is lightest.
23:47 - GEPRC has most powerful analog vTX. Evoque is weakest.
24:22 - GEPRC is most expensive. Diatone and Evoque are cheaper.
24:47 - Which is best? GEPRC, Diatone, or iFlight
26:13 - Is there any point in building your own any more?

Опубликовано:

 

31 май 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 441   
@IgnoranceParanoia
@IgnoranceParanoia 2 года назад
The numbers on the bolts refer to mechanical properties, eg 10.9 mean 1000MPa tensile strength and 900MPa yield strength
@JoshuaBardwell
@JoshuaBardwell 2 года назад
I didn't know that. Thanks for filling me in. I thought it referred to specific amounts of certain metals that steel is alloyed with.
@IgnoranceParanoia
@IgnoranceParanoia 2 года назад
@@JoshuaBardwell my materials destructive testing class at college, I knew it would come in handy one day…. Love the video. Tell me about it, building quads this year is much more expensive, the Kakute stack in my new FR7 is almost double the price it was last year.
@hateforall4012
@hateforall4012 2 года назад
@@IgnoranceParanoia hahahaha kinda like using trig or Algebra after high school…. Education win! Lol
@MayankJoneja
@MayankJoneja 2 года назад
Guess @JB learnt something that day!
@SLOSHPLOP
@SLOSHPLOP 5 месяцев назад
@@JoshuaBardwellhi… I just unboxed my Geprc and the antenna is super floppy? Like it’s not solid at all it literally seems like it in the way of propellers. What should I do? I don’t believe this is normal lol.
@lottedowse7353
@lottedowse7353 2 года назад
I love how excited you get about the spreadsheets!
@BlownUpp
@BlownUpp 2 года назад
Thanks for the recommendation on switching to Edge TX and ELRS - I made the jump yesterday and it was *so* easy to setup on both ends (besides soldering the wires to the tiny breakout pads on the FC) to setup. It took me less time to install, flash and bind both the TX and RX than it took me just to bind my TX16S to an XM+ RX! EdgeTX makes my TX16S feel like a brand new radio with all the new features and even the performance gain.
@Sav_FPV
@Sav_FPV 2 года назад
Finally you reviewed this. Thank you Joshua for all the work you put in that.
@robertaustinmasters8
@robertaustinmasters8 Год назад
Definitely my favorite go channel when looking for easy to find, thoroughly covered, need to know information to answer almost any questions I come across.
@crippledcarbonfpv
@crippledcarbonfpv 2 года назад
That new course is looking awesome Josh! Nice flying too!
@JP-qq2kn
@JP-qq2kn 2 года назад
Nice! I like the new freestyle obstacles in the yard. Do you have any plans to put led's or any type of lights on them for some cool evening rips?
@Adamlhodge
@Adamlhodge 2 года назад
GREAT ONE JOSH!!!!!!!!!! I REALLY LOVE THAT YOU STICK WITH FACTS AND IF YOU ARE BIASED YOU LET PEOPLE KNOW REFRESHING HONEST REVIEWS TRULY APPRECIATE YOU BROTHER
@thegeniuspig9587
@thegeniuspig9587 2 года назад
Love the intro. So true. Thanks again for the thoughtful comparison at the end too.
@slappomatthew
@slappomatthew 2 года назад
I have been a gep fan for YEARS. Built many of their frames back in the day and they were a very good value. having said that I enjoy building more than I enjoy flying.
@AGILISFPV
@AGILISFPV 2 года назад
Love your obstacles really nice and fun looking to fly through.
@BNIRc
@BNIRc 2 года назад
Can't wait saving up now absolutely love my AcroBee 65 great video 👍
@drone-vision
@drone-vision Год назад
Great flying in that wood box 📦;)
@TechnicallyTom
@TechnicallyTom 2 года назад
Not only do I fall into the “I enjoy building” camp but I like how I cover the motor wires better. I also like to have some quads with motors in the lower recommended Kv rang and some in the higher range. With bind & flys, you get two choices for different cell counts. I do think BNF quads are a good way to get started.
@jonah6496
@jonah6496 2 года назад
I've been looking forward to this review for weeks, and it didn't disappoint! Amazing review video Joshua! The mark five is a quad I'd like to buy, but it is a little pricey. The discussion on whether building is more cost effective anymore got me thinking. Maybe building a five inch on a budget is like building a tinywhoop now, it's cost effective to buy a BND with some parts you want and use the parts to build your own five inch.
@prismaticsoundwave
@prismaticsoundwave Год назад
I would say BNF quads are a godsend for countries which do not have a sizable FPV community. Living in Singapore, we do not have a huge selection of retailers from which to purchase parts to build from scratch and parts selection is also limited. You can argue we can purchase them overseas, but the shipping costs and currency conversions (especially with costly living standards) would simply make scratch builds too costly for beginners. Anyway, just want to thank you for your videos. Just started out in FPV with the Cetus X and simulators and already ordered this in 6S analogue to go further!
@solidfoxhound560
@solidfoxhound560 2 года назад
Really amazing stuff. Im learning so much from your videos
@QuadMcFlyFlies
@QuadMcFlyFlies 2 года назад
The similarities to the QAV-S JohnnyFPV edition are pretty remarkable :D Honestly though I'm glad to see an RTF company taking a design seriously even if they are taking heavy inspiration from other designs. They even made some nice tweaks in this one along the way. Definitely well executed. My only complaint would be they added a lot of weight in the process.
@davidgoldberg7032
@davidgoldberg7032 2 года назад
Well i learned something, Ty always a pleasure watch your videos.
@neilfpv
@neilfpv 2 года назад
WOW! Joshua! Your freestyle progress is extremely amazing! I don't have great control similar to what you did at 1:40. WOW!!!
@ThePieSnatcher
@ThePieSnatcher 2 года назад
I just remembered why I love your channel
@speedyturtlefpv3290
@speedyturtlefpv3290 2 года назад
Dang bardwell your skills are getting soo good!!
@SunriseWaterMedia
@SunriseWaterMedia 2 года назад
👀 Amazing flying through the obstacle in your field.
@yang74
@yang74 2 года назад
Very detailed evaluation and comparison!!!!Thank you!!!
@vladimircerovic
@vladimircerovic 2 года назад
Wow I love those obstacles! Gotta build something similar when we move to the house. Quad appears to be flying really good.
@StacemanFPV
@StacemanFPV 2 года назад
Having those built gates are really improving your flying. Nice!
@AIRWOLF
@AIRWOLF 2 года назад
Thanks Josh!
@aythixfpv
@aythixfpv 2 года назад
🤣🤣🤣🤣 the opening actually made me laugh. Good job JB. Also props to King Turkey
@Robert67909
@Robert67909 2 года назад
I've been flying The Mark 2 for three and a half years its my favorite freestyle quad. Now I need a mark 5.
@MJBold_1
@MJBold_1 2 года назад
brilliant video! thanks for this!
@olMadMaxlo
@olMadMaxlo 2 года назад
Look at you go, killing it on the cubicle.
@Rcschim
@Rcschim 2 года назад
I like how you've modded your level, eh property, to adjust to the advanced freestyle reviewers needs ;) That "chair" is a nice idea to practice loops and gaps... Mark5 is for sure not bad - reviewed Mark4 last year and it was great - and it is nice for guys like me who could build their own quads but who are just too lazy ;)
@danacummings8988
@danacummings8988 Год назад
I love your videos so much I am only 11 and you inspired me to start learning about fpv drones and I even bought a Cetus pro
@youzrnaim
@youzrnaim 2 года назад
Damn. Practice is paying off. Looking great, Joshua.
@onelastmarine
@onelastmarine 11 месяцев назад
What a great spatial training tool at 1:50 love your videos
@ShinyVideoStuff
@ShinyVideoStuff 2 года назад
Should mention that this is also the debut of the GepRC expressLRS RX! So you can get this BNF with eLRS.
@jacobreezyfpv6287
@jacobreezyfpv6287 2 года назад
Gosh Joshua you making me want another drone this frame is really nice
@AL_FPV
@AL_FPV 2 года назад
I have to say: you are getting really good at freestyle now! I'd love to see more :)
@DevArnold
@DevArnold Год назад
Those loops are sick!JB got tucks for days through those obstacles. I pray for a quad like this one day!
@jessiahd.6143
@jessiahd.6143 2 года назад
Another awesome video! I wish Race Day Quads had the Air Unit version I'd pick this up!
@DESOUSAB
@DESOUSAB 2 года назад
Hit on this channel about a week ago (I'm an RC crawler guy who is screwing around with an FPV setup). I've been binge watching the content and I think you may have me hooked. Might have to get into this hobby... Anyway - subscribed and liked.
@MzanziRC
@MzanziRC 2 года назад
I transitioned back to RC cars. FPV flying is so expensive in the beginning. Fly. Crash. Repair. Rinse and repeat. But FPV gives you a thrill like nothing else! Ok, maybe skydiving! :)
@andrewut7ya511
@andrewut7ya511 2 года назад
If you are gonna get into this you came to the right place. There is noone better than joshua for learning something today. There is alot of great channelS that can help but joshua is THE GUY, especially for newer pilots.
@SimpleMeFPV
@SimpleMeFPV 2 года назад
Fun intro 😆, wire loom tape great tip! awesome video as always 👍
@skyweaver3199
@skyweaver3199 2 года назад
2107.5 1960 kv motors, interesting. Also love those obstacles.
@ch3fpv
@ch3fpv 2 года назад
Sick!!! adding gates to yr compound....
@benkimmitt
@benkimmitt 2 года назад
Try the 3m friction tape. You’ll love it.
@eduardoepsilveira
@eduardoepsilveira 2 года назад
Joshua, You are the best.
@minkorrh
@minkorrh 2 года назад
I bought a knockoff Mark 4 frame (cuz I'm that guy) the and I was very impressed with the stability and smoothness of flying. I can only imagine they've done it again. Building your own has its own rewards in the amount of stuff you collect to enable you to repair, replace, and get back in the air. It's not cheap tho.
@GioFpv
@GioFpv 2 года назад
Purchased this quad the day after I saw this review which was exactly 2 days after the video was released. Bought the frame kit and I built it myself, with my fav components. 2207 2021kv 6s. Disappointed to find out it takes only 30x30(I might drill some holes in the extreme case). Anyway the build is solid and designed in great details. Weird how it says had front arms and rear ones, which to me they look similar…mheee. Been bashing it a lot, put it under my usual stress test and so far I’m liking it. Also great it takes 5.2 prop size and motor to motor gives such a nice flying experience that I love. Highly recommend to try this quad
@jmillerfpv
@jmillerfpv 2 года назад
I’m getting ready to move to the country. I can’t wait to build some obstacles like you have! The freedom to fly the way I want anytime, and be far away from people will be nice. BNF quads are really good these days! I really like this Mark 5!
@MadRC
@MadRC 2 года назад
Great video. I really need to try one of these new pre builds as they have just come on som much. As you say it close to make no sense to build for the average user now. I was close to getting the Evoque but when I stop pending on other things I will pick one of these up. I like what they have done here.
@bradgibson1976
@bradgibson1976 Год назад
Mine is coming tomorrow in analogue 6s, so excited. My Evoque dropped 1 motor today on my last pack only time its gone down after 8 months and 1000 packs, durable even the 20x20 isn't affected. Sorry sir lol. J,B. 😊 your a legend 👏 🙌 ❤ 💙
@casey22857
@casey22857 2 года назад
I still have the mark 3 and it's still my favorite quad as far as fill goes.
@RRGCGarage
@RRGCGarage 2 года назад
I like the wire covers but didn't want to re solder all the motor wires to swap to new ones when I changed bottom plates so I took my rc lexan scissors and cut a tiny gap in the bottom center to slide the old ones off and new ones on. The tape holds it down just fine with a hair missing and the top and sides are still whole.
@andrewut7ya511
@andrewut7ya511 2 года назад
That looks pretty nice, if i was to buy it i would order a few extra sets of front end plates for future repairs but it seems pretty good to me.
@MzanziRC
@MzanziRC 2 года назад
Damn! You got REALLY good!!! Watched you many moons ago when I flew quads. Costs just got too much! LOL! One of your videos just popped into my feed again. Miss those days and I miss watching you. I'm subscribing for nostalgic reasons! 😀
@ImperialArmour
@ImperialArmour Год назад
This thing is terrifying loud, PERFECT!
@BROK3N1MAGE
@BROK3N1MAGE 2 года назад
The analog vtx on the mark5 is what has me sold. I know geprc sent you the one with an air unit. However it would have been cool to see how well that vtx would hold up in a parking garage 🙂👍
@aztecjoe29
@aztecjoe29 2 года назад
You are the man thank you brother
@steviefpv
@steviefpv 2 года назад
I use them motor wire shields but I also put layer of electrical tape over them so the don’t shatter. They last ages then before you need to replace one
@sinkWad
@sinkWad 2 года назад
For anyone watching this now- GEPRC as of MAY 2022 no longer uses MPU6000 - Its now listed as 6-Axis. Thanks for all the great content JB! I Picked one of these up!
@jianliu9420
@jianliu9420 Год назад
So os 6 axis better than mpu6000?
@gus8378
@gus8378 2 года назад
I wish the Vista had two antennas for bigger coverage while staying light
@supernatural802
@supernatural802 2 года назад
Nice work on those sticks!
@simmoakagoofy
@simmoakagoofy Год назад
Love the video. The information was on point and helped me massively. Also want to say thank you soooo much from a viewers perspective.....There was no lengthy intro branding clip taking up the first minute before any content, there was not the obligatory "HEY GUYS dont forget to hit that like and subscribe" yelling at the beginning and when you do mention a like, we are already 10min into content. Brilliant! So much so that I just felt the need to comment and say keep up the good work and your videos are informative as well as a pleasure to watch!
@ChrisParayno
@ChrisParayno 2 года назад
Love the obstacles!! 26:46 accurate. It's just not cost effective to build a quad anymore unless you start accumulating spare parts and multiple quads due to crashes. Even then, even frames have gone up in price... Some hitting $100. You really end up paying 25 percent more when you build your own, and then you have to deal with the "did I do this right" question.
@melon9088
@melon9088 2 года назад
Did you say/see this same thing on reddit? Or am I just getting some crazy deja vu?
@bugsy742
@bugsy742 Год назад
Thing is there is no reason for frame price hikes - they just use the bandwagon to excuse it, fpv companies aren’t our friends anymore unfortunately and they’ll definitely piss in yer pocket and tell you it’s raining! 👍😎
@ChrisParayno
@ChrisParayno Год назад
@@melon9088 I don't go on Reddit but it's a general observation I've made this past year building quads
@ChrisParayno
@ChrisParayno Год назад
@Evolution Drone Works same!
@djilly75
@djilly75 2 года назад
I didn't you built that dive gate thing. That is so cool. I should do the same
@kdeclinetostatendeclinetos6707
@kdeclinetostatendeclinetos6707 2 года назад
I have lock-tight only at the bottom screws in my mark4 frame. I always open from top, never had to unscrew bottom screws.
@MrSabram07
@MrSabram07 2 года назад
Damn Joshua you're getting really good at them tight power loops
@neoroggensack1244
@neoroggensack1244 Год назад
1:19 "And I call this one the Prop Breaker."
@QuandarNl
@QuandarNl 2 года назад
I replaced all my T-Motor stuff with GEPRC. I also really love their tiny drones.
@LumpyFPV
@LumpyFPV 2 года назад
Dude! The dive cube thingy! Nice ripping my guy. 🤌🏻🔥🔥🔥 Thanks for the review too. 🎩
@DrFrantic77
@DrFrantic77 2 года назад
Nice review mate, it seem, @GEPRC goes better and better
@camdynkellett6782
@camdynkellett6782 Год назад
Bought a mk5 two months ago and I'm super stoked! Was lucky to find an old stock deal with an MPU6000. This is my first 5" quad and I'm blown away with the performance and stability. First flights were on a 4s 1300 and for cruising I managed to get a consistent 7-8 min. I now use a 6s 2000mah pack for cinematic filming and with a gopro I easily reach 8-10min even in strong wind! Great quad, no issues so far
@jianliu9420
@jianliu9420 Год назад
Can you hold it steady hoovering? Is it precise in control?
@camdynkellett6782
@camdynkellett6782 Год назад
@@jianliu9420 It's a great radio for the price, and I was super impressed with the feel of the gimbals and the control I had. At the end of the day, it's up to skill... the best pilot may complain about a few things, but they still manage to fly insanely well. I think it's a good option, but the Zorro is also another great option to look at as well!
@armandor.calderong.9135
@armandor.calderong.9135 Год назад
​@@camdynkellett6782 hello, I think you put that comment in the wrong place. Have a nice day.
@camdynkellett6782
@camdynkellett6782 Год назад
@@armandor.calderong.9135 Haha good spotting! I don't even know where that one would have gone! Thanks! Had a great day today, hope your's was good too!
@PeterPetermann
@PeterPetermann 2 года назад
I actually bought the frame and did my own build on it. What came in the box was amazing, all sorts of screws i'd need, all sorts of foam and 3d printed parts, allowing full flexibility into the build allowing for almost any component I could think of. (only thing it doesn't take is 25.5mm aios) well done geprc
@francescorobotti8341
@francescorobotti8341 2 года назад
Same here, it seems a super frame..
@glytch5
@glytch5 2 года назад
gaffer tape FTW. rips perfectly into any size section.
@mattwilson1305
@mattwilson1305 2 года назад
You have the best job in the world
@jessearmand
@jessearmand 2 года назад
rcinpower was the first I noticed who released 2107 sized motors. The stator length is actuallly 7.5mm, so it should be the same size as this one. The GTS V3 motors have been tested by Chris Rosser in one of his motor testing videos together with Xing2, FPVCycle motors, and Wasp, another motor from rcinpower.
@Lloyd_workshop
@Lloyd_workshop Год назад
it's awsome that Quagmire is teaching us about drones :3
@Whamola
@Whamola 2 года назад
I appreciate how much info these videos give, but I must have missed or can't find again if he tested the 4s or 6s version.
@kevinp.2039
@kevinp.2039 2 года назад
Hey Josh, thanks for the video. I wanted to note your explanation of the metal front end is a little off. The metal part’s manufactured and post-processing will result in it being more brittle / stiff or soft ‘ bendable. Composites also have variations.
@chrisB_OG
@chrisB_OG Год назад
Sick intro JB
@digitalpituitary5226
@digitalpituitary5226 2 года назад
You rock! Every time!! 🏅🏆💯
@VulpeculaJoy
@VulpeculaJoy Год назад
I bought my MK5 not long after this video and so far it's performing pretty good. I replaced the default FC with a Mamba Mk4 F722 App, since GEPRC somehow had not added the barometer and it also just didn't want to work with the SpeedyBee app. After a crash I burned the ESC and replaced it with a Mamba F40. I destroyed 2 LiPos on crashes and have yet to kill a motor, but the frame just tanks crashes at 50kph into concrete like a champ. If I need to replace the motors, I'd definitely get some RCinpower GTS V3 2107 Plus' or Wasp Majors.
@studiodeepdive6165
@studiodeepdive6165 2 года назад
Looking to move in from DJI FPV to a legit quad. This looks like a good place to start!
@FrodoFPV
@FrodoFPV 2 года назад
Hi Joshua bardwell i have bought the iflight evoque f5 and i have blown 3 esc's and the analog vtx is only puting out 10 mw when set on 600mw thats also why i just bought dji
@quentincampbell5865
@quentincampbell5865 2 года назад
I have built quads from the ground up before. But yes, BNF is cheaper. What is good about it you also get a nice base starter pack to build on. Add on, change things and fix. There is still that fun.
@PesterBotLoFi
@PesterBotLoFi 2 года назад
building your own and then customizing the thing would give you the best of both worlds really.
@YoYoYo
@YoYoYo 2 года назад
The best part about this video is the freestyle park you made. Please do a video on that. :)
@martinverbaas
@martinverbaas 2 года назад
I fly 4" only so no luck. Thanks for the video
@borisstihkrajnc6234
@borisstihkrajnc6234 2 года назад
Before buying my geprc smart 35 4 months ago, I was so into dji mavic family and video recording. But then I saw some freestye videos and I said to my self I want to fly like that. So I entered this nice new hobby of mine and thank you Joshua for these videos. I learn something new each time. I have no electronic skills but learned alot from yout videos. In the end, I just want a drone and fly it. So maybe I think this Mark 5 is on my list. If I want to sound poetic, I believe that building a drone gives some deeper connection with it. You are a proud owner of your build. But if you just want to fly it, dont bother just buy it and a lot of spare parts, I learned that the first day when propelers and arm broke. And btw you have fans in Slovenia.
@monolith2001
@monolith2001 2 года назад
I have both the Roma V2 and the Evoque. I got the Roma first (late summer 2021) and my wife bought me an Evoque for Christmas. I have to say out of the box the Evoque was the better drone but I have tuned and gotten my Roma V2 so synced to the way I like to fly, I prefer it over the Evoque. The Roma feels punchier on throttle. The Evoque is great and looks great late evening (LEDs are gorgeous and configurable...running a fixed Seattle Seahawks ble/green theme right tnow. I did swap the camera for a Runcam Phoenix 2 (not a JB) as the default camera was terrible in variable light conditions. 600mW VTX has not been as much a liability as I thought though Roma is still better. I like the Mark 5 but with the cost and I don't need another 5" will keep me away. If they make a 3-3.5" of it, I am there day one as I love the basic design.
@apachesmokemachining6487
@apachesmokemachining6487 2 года назад
Because I like building quads 😉 great video though 👍🏻thanks for the time you put in it for us
@ttttenney
@ttttenney 2 года назад
The cloth tape is called Friction tape, available at most big-box stores, for those who want to know.
@SilverbackSasquatch19xx
@SilverbackSasquatch19xx 2 года назад
I have in months gone from learning to fly on a bnf to cnc cutting my own carbon fiber frames and building my own but I still keep good bnf quads on my radar, sometimes they provide inspiration for your tune or hardware on another quad
@funkyfpv9847
@funkyfpv9847 2 года назад
Do you build custom orders?
@SilverbackSasquatch19xx
@SilverbackSasquatch19xx 2 года назад
@@funkyfpv9847 I recently got into contact with some of the major companies to be considered for design and development. I haven’t cut for someone else yet but I’m interested. What kind of frame are you into? Are you looking to have it completed with electronics? What kind of flying do you want to do with the custom frame?
@SilverbackSasquatch19xx
@SilverbackSasquatch19xx 2 года назад
Just ordered some more carbon fiber and 3D printer tpu! I have a frame in the works I’m getting excited to produce!
@scu-dub
@scu-dub 2 года назад
I ABSOLUTELY LOVE JB's PROPERTY 🤤 I wouldn't leave to fly anywhere else lol and the new track set up is SUPERB 🤌🏽 I can't believe geprc slapped a 1600 mw vtx on this quad😳 INSANE! I know it's not that big of an issue but I like how diatones camera mount has the degree setting for the camera angle 👍🏽I know I'm a newb😒 lol I have been looking at all 3 of these quads and really like all 3 and wish I could have all 3 but I think I know which one to pull the trigger on😏 awesome review....but then again they all are 🙄 lol✌🏽ps...I thought I was the only one to being picky about the quality of screws good to know that someone thinks it matters😁
@antontevs
@antontevs Год назад
I have droped this frame from 30 meters (my failsafe mistake),and its still OK!
@CHAINREACTION238
@CHAINREACTION238 Год назад
Bought the Walksnail version of this quad Dec 2022. Current meter burnt out in two flights. No crashes. Geprc support didn't offer a paid shipping label. I paid for shipping from US to China. Quad got lost in the mail after it cleared customs in China. Tracking last ping was Jan 8 23. Geprc support acting like I broke it, I shipped it back, tough luck.
@ChasePhilport
@ChasePhilport 2 года назад
12:10 use hockey grip tape. stretchy, very strong adhesive, holds in warm and cool temps, easy to remove.
@ooOoo.....
@ooOoo..... 2 года назад
Re: motor diameter. I always preferred a wider motor instead of taller motor. My thoughts have been the wider diameter is able to spin up the prop easier.
@sunsetpark_fpv
@sunsetpark_fpv 2 года назад
@ 20:43 you better be careful - that mortar seems aimed very cleverly at that little structure in front of it...... 😎 Awesome review - makin' me wish I had one LOL 😁
@JC-qy6cx
@JC-qy6cx 2 года назад
You can buy a go pro subscription separately to the hero10 and get your replacements via that
Далее
GEPRC Moz7 is 7 Inches of Awesome // FULL REVIEW
34:46
I need your help..
00:28
Просмотров 2,5 млн
Big Mouse 😂
00:13
Просмотров 108 тыс.
ГЕНИИ МАРКЕТИНГА 😂
00:35
Просмотров 758 тыс.
2022 - 5" Freestyle FPV Drone Build
38:34
Просмотров 732 тыс.
FPV New Product Roundup // January 2024
41:37
Просмотров 62 тыс.
The GEPRC Mark5 is AMAZING! Will it be my favourite?
17:01
Which FPV Drone is Right For You?
12:03
Просмотров 32 тыс.