Why didn't I build this sooner? // Woodworking assembly table

Подписаться 276 тыс.

Просмотров 424 тыс.

50% 1

✅️ TOOLS AND SUPPLIES IN THIS VIDEO:
►Undermount Drawer Slides (21”) - amzn.to/3HznSqf
►Undermount Drawer Slides (15”) - amzn.to/3kNUYcU
►Countersink Drill Bit - amzn.to/3R5VgIt
►Tape Measure - amzn.to/3XBZBFA
►Speed Square - amzn.to/3R9cqos
►Jig Saw - amzn.to/3Djuu9P
►Drill/Driver set - amzn.to/3DFicsD
►Pocket Hole Jig System - amzn.to/3Y2CIe7
►Dado Blade Set - amzn.to/3XxPpxT
►¾” Pipe Clamps (clamps only) - amzn.to/403PHhF
►Small F Clamps - amzn.to/3jbl7SH
►Adjustable Levelling Feet (x6) - amzn.to/3kOBmp1
►½” Drill Bit - amzn.to/3HwOFna
►Self Centering Drill Bit - amzn.to/3kFHVKF
►80/20 Rails (780mm & 1143mm) - 8020.net/40-4080.html
►Drop in T Bolts (x12) - 8020.net/13148.html
►6mm Washers (x12) - 8020.net/13-6041.html
►6mm Nuts (x12) - 8020.net/17-6065.html
►Festool Clamps - amzn.to/3JhXfY4
►Microjig Clamps - amzn.to/3RbDR0R
►Formica Laminate (4x8 sheet) - amzn.to/3XDLkbF
►Laminate Scoring Tool - amzn.to/3Y1kpq0
►Contact Cement - amzn.to/3WES73w
►Laminate Roller - amzn.to/3j9Lbxm
►Trim Router - amzn.to/3kJXilg
►1” Rabbeting Bit - amzn.to/3XHJfv7
►Drawer Pulls - amzn.to/3JhPhhy
►UJK Parf Guide - tsoproducts.com/tools-equipme...
►Wood Glue - amzn.to/3j69Piu
►Festool Domino XL - amzn.to/3Rd8aUT
►Doweling jig - amzn.to/3kKoC2V
►Mallet - amzn.to/3Jj2lUe
✅️ GET THE PROJECT PLANS:
► Assembly Outfeed Table: mwawoodworks.com/product/tabl...
► Build My Shop Plan Bundle (Save 50%) - mwawoodworks.com/product/the-...
► The Whole Enchilada Plan Bundle (Save 65%) - mwawoodworks.com/product/the-...
🔴 SUBSCRIBE to my channel: ru-vid.com?...
✅️ WHAT TO WATCH NEXT
►Organize Any Shop - • 11 Simple Ways to Orga...
►Five Drill Press Upgrades - • 5 ways to IMMEDIATELY ...
►Peter Millard's video on making an MFT dog hole top - • I Make an MFT top with...
► How to Use UJK The Parf Guide System - • UJK Parf MkII Guide Sy...
✅️ HOW TO SUPPORT MY CHANNEL
Join my Patreon community: patreon.com/MWAWoodworks
Get Project Plans: bit.ly/download-project-plans
Get some MWA Woodworks Logo Merch: www.mwa.keyapparelstore.com/
SUBSCRIBE : ru-vid.com?...
✅️ LIST OF THE TOOLS I USE IN MY SHOP : bit.ly/tools-i-use
*Disclaimer - As an Amazon Associate I earn from qualifying purchases
✅️ Other Affiliate Partners
Bits and Bits Co. - 10% OFF using code MWA10 - bit.ly/48Pw5Cq
TSO Products - tsoproducts.com/?ref=MWAWW
Taylor Toolworks - lddy.no/1gngh
✅️ MWA WOODWORKS ON SOCIAL
Instagram: / mwawoodworks
Facebook: mwawoodworks
Pinterest: / mwawoodworks
⏱️ Chapters
00:00 Intro
00:21 Cutting Frame Parts
03:00 Joinery
04:20 Frame Assembly
07:45 Cutting and Installing Cabinets
10:19 Making Drawers
14:26 Aluminum Rails
15:30 Making the Top
Table Saw Outfeed and Assembly Table
#shopproject#woodworkingproject#diyprojects

Хобби

Опубликовано:

8 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 358

@joshuaingram34 9 месяцев назад

I'm watching this one shortly after watching one of your older videos and I have to say your VO style has improved dramatically. It sounds more like an actual explanation and not just a boring script read. Much appreciated!

@espenskeie 5 месяцев назад

Great. I am going to build a workshop from scratch and I believe this is the best workbench I can find on RU-vid.

@74nrt Год назад

Great bench! Really like the design and your choice of materials and joinery for this... just what I need to build for myself, thanks!

@johndaniels9957 3 месяца назад

Great job. I wish my shop was large enough to use this design.

@300Exige 6 месяцев назад

Enjoyed watching that. Lovely bench 🎉🎉

@rrpp1425 5 месяцев назад

Excellent work.

@wilkoslavakia Год назад

Thing i love about your style is you make it look all so easy then you explain what you would do if it was not working as expected that's the trait of a good teacher

@MWAWoodworks Год назад

Hey! I appreciate the kind words!

@ConwayT91 Год назад

The end result is simply amazing! This will make you very happy for years to come. Awesome video

@MWAWoodworks Год назад

I hope so 😃

@burningtree878 Год назад

Beast Mode Workbench! Nice job, looks great and thanks for sharing your experience 😃

@MWAWoodworks Год назад

You're welcome 😊

@TedAlexander24 Год назад

That’s a really nice table/cabinet. Also like that you added the 3 drawers. Your videography is outstanding!

@MWAWoodworks Год назад

Thank you, Ted! 😃

@daveparker2477 2 месяца назад

Not sure you covered this, but formica is a brand name. There are several different names that can be used, wilsonart being one of them. The correct terminology is laminate and there all pretty much the same. Great build keep up the good work.

@woodbutcher 10 месяцев назад

Brilliant build! Great job sir!

@xzytqweo3538 Год назад

Aren't you as cute as a speckled pup in a red wagon...🐕 Great job! Awesome shop too. What is so nice about your work bench is it can be configured in many ways but remain the same size and shape. Thanks for sharing this video.

@brianaustin637 Год назад

Definitely saving this for a shop remodel. Great job!

@MWAWoodworks Год назад

Awesome! Glad you liked it!

@MCsCreations Год назад

Fantastic work, Matt! Great looking table! 😃 Stay safe there with your family! 🖖😊

@MWAWoodworks Год назад

Thanks 😊

@thanos2149 5 месяцев назад

Nice work. I also made an out feed / assembly table 14 or so years ago. The annoying part was when you need ur table say when you are assembling something at the same time, and your work piece gets in the way. 👊

@BruceAUlrich Год назад

Great outfeed! Man, that thing is massive and you really thought through everything.

@MWAWoodworks Год назад

It's a beast 💪

@markd.621 11 месяцев назад

Nice video. I now might have to re-make my outfeed table. I like the look of the black Formica, but I chose white for my mine because I can draw on it full size to make sure parts fit. Yes it does get dirty, but it's a shop.

@michaelbradford4444 Год назад

Awesome table! I love the black top and will incorporate that into my next work table ect. Good video , really good job!

@MWAWoodworks Год назад

Thanks 😃

@robertschmidt6383 Год назад

That is one beautiful work/outfeed table. Very cool design/materials also. 👍😎

@MWAWoodworks Год назад

Thanks Robert!

@davidcole333 Год назад

If a guy that was setting up a new shop was building this table, I would recommend that he incorporate a router lift into it. I would also suggest changing the top to incorporate a downdraft table. But the way you built it...man I am in love. Beautiful project.

@MWAWoodworks Год назад

That's a great idea! I already have a router lift built into my table saw, if you squint real hard you can see it in the thumbnail picture but I agree that would be a great addition to a table like this.

@ErinIsBlueBlue Год назад

This an impressive video, beautiful work !

@FisherCatProductions Год назад

Nice design. Beautiful, precise work. Thanks for th inspiration!

@MWAWoodworks Год назад

Thank you! Cheers!

@5280Woodworking Год назад

This is a very nice design, well thought out. I did something similar to my 40x90 workbench, breaking into 3 pieces so I could CNC whatever type of top I want (dogs, t-track, combo, etc.) One recommendation is to give access to the top t-slot of your extrusions. The Kreg Automaxx clamps fit and they are brilliant for top or side clamping, quickly and easily. They were a game changer when I added extrusion to all 4 sides of my bench. I hardly use my Festool clamps anymore.

@MWAWoodworks Год назад

That's true although I don't have those clamps... yet 🤣

@scottpollock1714 Год назад

Awesome build! One suggestion - if you didn't want the T tracks on the sides to protrude - just bore 1" holes on either end of the t track before installing it, it works great and you don't snag anything on the edges!

@MWAWoodworks Год назад

Great idea!

@ThomasLykins Год назад

Great work Matt! Thanks for sharing!

@MWAWoodworks Год назад

You're welcome 😊

@tongyong007 Год назад

Very professional work sir. 🤙

@user-lk7zt7uv8j 5 месяцев назад

I'm new here, but after a couple of videos, it was an easy decision to subscribe. I'm enjoying your style. You have lots of compition on the tube, but it seems like you are up for the challenge. Keep up the good work.

@scottromero2091 4 месяца назад

Nice Table😀

@SpencleyDesignCo Год назад

killer work on the outfeed table!

@MWAWoodworks Год назад

Thanks!

@meperson Год назад

That is quite a build and amazing out feed table. Could be main workbench for normal woodworker like me 🙂. I didn't realize 80-20 works for Festool and microjig clamps - thanks for sharing!

@MWAWoodworks Год назад

It's going to be my workbench as well!

@jaykepley5238 Год назад

Another great build!

@MWAWoodworks Год назад

Thank you Jay!

@mc-yt2rc Год назад

Thats fantastic! wish I had the room!! subscribed and looking forward to watching your channel.

@pbates33 Год назад

Excellent table and video! Looking to do a smaller out-feed table myself in my my new shop!

@MWAWoodworks Год назад

Awesome

@pacificcoasttrains3785 Год назад

Seems to be popular in my feed today- this is the second I've seen (the other was Jason at Bourbon Moth). Very similar, but with some differences that reflect personal preferences/needs. Nice work putting this together- lovely finished product!

@MWAWoodworks Год назад

Thank you sir!

@chrisdemeglio6707 8 месяцев назад

Excellent build. I like the setup and all of the storage space you have. Your narration also makes it simple and easy to understand what steps you use. I agree with one of the other comments that edge banding after the Formica is easier and more accurate. After all is said and done, what do you think the total cost of building a table like this would be? What is the total size of the table. I have a single car garage that I'm getting setup and, to be honest, I did it out of construction lumbar and rough plywood covered with Formica bc of the cost. Looking forward to watching some of your other vidoes as well.

@joabverschoor Год назад

😉Fantastisch, en heel goed uitgelegd. Dank je.

@MrFrenchy3 Год назад

Very well, good work

@snobear41 Год назад

I built one, (not quite as fancy as I have a limited budget) Bought a solid core exterior door 36" x 80" for top, utilized some re-purposed 4x4's (from neighbors' fence) and made a cantilevered shelf on one end for my old craftsman tablesaw, large hole in shelf with garbage bag (one end cut off) as a sawdust chute into shop built wooden box on castors to catch sawdust. End vice, storage drawers x 4, shelves for tools i seldom use Glue & tape rack & clamp storage- Tyler (I wish you tube would allow posting of pictures)

@MWAWoodworks Год назад

That's making great use of what you have available!

@j.r7872 Месяц назад

Awesome!

@frankcornfield5915 5 месяцев назад

Thanks for this great video for an excellent project. I'll be starting my version of this next week. I need to incorporate a router with a fence that is easily removable.

@MWAWoodworks 5 месяцев назад

That sounds awesome!

@jimrosson6702 Год назад

Great video amazing build the table looks amazing

@MWAWoodworks Год назад

Thanks, Jim!

@chrisbroome Год назад

Looks amazing!

@MWAWoodworks Год назад

Thanks!

@thomasblaylock8528 Год назад

Man, you did a great job.

@MWAWoodworks Год назад

Thanks!

@Ataraxia_Atom Год назад

I really like the 8020 aluminum extrusion trick you did here. I'm gonna add that to my work bench

@MWAWoodworks Год назад

It's so handy

@craigrmay7935 Год назад

Great looking work sir!

@MWAWoodworks Год назад

Thank you Craig!

@DIYwithDennis Год назад

Beautiful! Thanks for sharing!

@MWAWoodworks Год назад

Thanks for watching!

@imsowright90 5 месяцев назад

Nice poject.

@fb510m 7 месяцев назад

Really sweet!!

@MWAWoodworks 7 месяцев назад

🙌

@12982blackjack Год назад

And just when I thought I had my new outfeed/workbench table drawn up, I get new ideas. Now I'm back to the drawing board, lol.

@MWAWoodworks Год назад

Haha awesome! Glad to inspire your work!

@denyhelson1217 Год назад

Amazing work, you just gained another subscriber. hugs from Brazil

@MWAWoodworks Год назад

Awesome, thank you!

@BenNawrath Год назад

I have an outfeed table with a pre-fab maple top with a similar dog hole pattern. I enclosed it underneath, slapped a DC fitting on the end apron, and now the entire thing is a down-draft table. Super handy! Not nearly as big as your tho. Nice work!

@MWAWoodworks Год назад

Oh wow that's awesome. I need to make a down draft table

@BenNawrath Год назад

@@MWAWoodworks I need to use a block of wood if I want to use a hold-fast, because they’ll whack the little 1/4” ply if whatever I’m holding is thin, but that’s a small compromise. I just screwed thin plywood rails at a slight incline onto the front and back apron, slid the plywood in, then held it in with blue tape. So if I drop something in there (and can’t get it with a magnet), I can take the tape off and fish it out. Or fish it thru the dust port. Even if you have a shop vac on a random orbit sander, it’s nice to have that to really get the dust flowing away from your face! I just disconnect the hose and use it for my router table or drum sander. Super handy.

@rajrooplal7595 Год назад

Looks Great

@MWAWoodworks Год назад

Thanks Raj!

@NWGR Год назад

Amazing job. 🙂

@MWAWoodworks Год назад

Thanks!

@docpugh Год назад

You just made an instant fan.

@MWAWoodworks Год назад

Woo hoo!

@johncollins500 Год назад

Looks great!!!!

@MWAWoodworks Год назад

🙌

@PaganWizard Год назад

I think it's probably best that you put the edge banding on your table top, after the formica. This actually conceals the razor sharp edges of the formica. GREAT BUILD!!!!!!!!

@steviewonder9209 7 месяцев назад

With the added benefit of looking awesome- the light maple against the black Formica really pops.

@roostermarques3583 7 месяцев назад

I regret not subscribing to your channel earlier you got a lot of useful information thank you for your service.

@MWAWoodworks 7 месяцев назад

Thanks so much 😊

@pointblankokc Год назад

That's a monster table man ! Very nice !

@MWAWoodworks Год назад

It was a monster to move around!

@pointblankokc Год назад

@@MWAWoodworks Oh I bet ! I'm fixing to build me a new outfeed/assembly table. Gonna have to steal a couple of your features to add to mine. I'm very impressed.

@wojo1034 4 месяца назад

Hello Matt, love the videos and I have learned a great deal from you. I have an existing outfeed and work station. You inspired me to change the top to an MFT. My question is, what is under yours? Drawers, cabinets? Where does the dust and other stuff drop into? Thank you and I appreciate your efforts!

@allent555 Год назад

Great video, question how do you manage saw dust in the dog holes?

@whippoorwillwoodcraft Год назад

Awesome outfeed! I’d love to make a smaller 4x4 version for my shop

@MWAWoodworks Год назад

Nice!

@keepitfixit2736 10 месяцев назад

Lmao when you need a fully tool loaded shop to build a an out feed table.came out badass man can’t wait till I collect more tools for my chop.

@MWAWoodworks 10 месяцев назад

Thanks brother!

@golfinusa 6 месяцев назад

Great bench! Building mine based on this design - with some tweaks! Did you build your bottom rails low enough (or high enough) to go over/under the dust collection port? How did you integrate your dust collection with this setup?

@fdort3971 10 месяцев назад

@MWAWoodworking...that sir...is a thing of beauty! I'm totally jealous of your work shop...Just found you today...loving the humour...man glitter...lol.

@matthewha6289 Год назад

Sick workbench, been thinking about making one and really like the design! Can you maybe do a vid showing different ways you use the bench dog holes? I feel like a lot of workbench videos show them built in, but don't really go over what you use them for haha

@MWAWoodworks Год назад

Good thoughts!

@masontejera506 Год назад

Even though I have a large table saw, I still end up using a track saw to break down ply wood. So I think my out feed table is going to incorporate track saw accessories, festool dust extractor and cyclone. Maybe even integrate sanding storage 😅

@MWAWoodworks Год назад

All great ideas!

@YouTuber-mc2el Год назад

Nice outfeed table. I built a ROUBO split top bench and the design has the outside face of the legs flush with the top for smooth unencumbered clamping. That might have been a nice idea to work into yours. Don't get me wrong, again that is a nice table.

@fredmorina861 8 месяцев назад

Hi. Great video. What size Aluminum Extrusions did you use to properly hold the dovetail clamps? I like this as an option to routing out my own in hardwood. Thanks.

@chrismark4666 Год назад

This is awesome! Do you have the cnc file available? Looking to machine something similar for my top!

@mmanut 7 месяцев назад

NEW SUBSCRIBER, GREAT OUT FEED TABLE‼️‼️ Vinny 🇺🇸

@MWAWoodworks 7 месяцев назад

🙌

@FranksDIY Год назад

looks awesome

@MWAWoodworks Год назад

Thanks!

@bradschak 11 месяцев назад

Tool envy. Have it, I do.

@dan__________________ Год назад

Bessey makes extension joiners for their parallel clamps. I have used mine more than I originally thought I would.

@MWAWoodworks Год назад

I think I have those.... somewhere 🤣🤣🤣

@henrydiaz720 9 месяцев назад

And here I thought I'd invented that! 😂😂

@cinemaipswich4636 Год назад

At one employer, we had a "spindal saw". It was a cast block with a movable vertical mounted motor, to which a blade was mounted. I could raise the spinning blade up or down by 150 mm.

@jessemiller8818 10 месяцев назад

I'm about to do a similar top on some old kitchen lowers. I've never made a counter top. Do I need to account for any overhang?

@user-sm4ew3hr1y 10 месяцев назад

theres so many little things with these tables that i think people notice after the fact like what happens when something falls thru the hole? how do you retrieve it. Also when dust falls in there, how do you clean it up? i think a table that addresses this and the other little things would make an ultimate table. I know dennis from hookd on wood addressed this issue and well thought out. Cant wait to make mine. great video still

@chelaf 9 месяцев назад

Reminds me of Jason’s (Bourbonmoth) outfeed. Nice

@mindyhall4638 Год назад

Great looking table and love the idea of the aluminum extrusion; thanks for all the tips on this one. Have a question about the fence on your MFT…do you have a video about that? Looked interesting and I think I’ve seen it on Bents’ Woodworking but wasn’t sure if it was the same one. Just curious. Thanks!

@MWAWoodworks Год назад

Yes it's the same one Jason uses from Benchdog UK. I don't have a product specific video on it but I believe he might.

@mr.iannone7519 Год назад

So those bessy clamps you have.... the holes on the end are for a bracket you can buy and turn 2 of your 50 inch clamps into a 106 inch clamp. Awesome build!

@MWAWoodworks Год назад

Yes! I need to invest in a few of those.

@TheAaronReynolds 4 месяца назад

Love it! Where are you getting your maple? I appreciate the plywood source from another video! 👍 -Your friend from MJ

@flatlander523 Год назад

Very nice job Matt. It looks great and I'm sure it's going to be very serving to you.Sometime soon you may consider a portable moxen vice for the top like the one on Tamar`s 3x3 channel.

@kizermergenschroer5096 Год назад

Great build! Thinking about replacing my outfeed/assembly table so this might work nicely. One question though....I'd like to do the dogholes but get lots of sawdust and shavings on my tabletop, any ideas on how to keep all this from falling through and making the inside of the drawers and cabinet a mess? Thanks!

@BeholderThe1st Год назад

A small 1/4 hardboard sloped towards the sides of your table under the tabletop can allow most of the dust fall towards the sides but shield things underneath.

@Funknwanker Год назад

The edge banding with the maple after applying the top is probably better. The maple takes the brunt of the damage from things banging into the side and prevents the Formica from getting those ugly chips.

@fredyquiroz7654 Год назад

Hey could you do a video of your miter station, a review I guess, what you like, what you would do differently? Is the depth you went with the right depth? Also how many sheets would it take to build that miter station you have? Thanks a lot love your videos

@MWAWoodworks Год назад

I've got a video on the miter saw station on my channel as well as plans available 😉

@northstar8105 3 месяца назад

I have a similar top that has aneurisms wherever moisture got into the particle board below. Hope yours does not have the same malady.

@moesawad Месяц назад

Did you join the two pieces of the mdf together or did you not need to because they are both secured to the edge banding?

@AlanHenry-mg5ot Год назад

I have been looking at building an outfeed table for my table saw, but my garage is not solely for woodworking. I was wondering what you would think about making an outfeed table out of 4 separate tables that could lock together. any thoughts on ideas for locking these tables together? Thanks. BTW, I love your channel. The various shop ideas have inspired me to get most of my tools off of just clamping to the bench top and actually making individual cabinets for each. I'm also about to start a built in cabinets for my wife based on your quick cabinet designs.

@MWAWoodworks Год назад

I've never see someone try ti wrangle four tables into one but I have seen people do it with two. I think they used barrel locks to secure them together

@Kot-Bazilio Год назад

Это шикарно👍

@MWAWoodworks Год назад

👍

@sandrarattray1202 5 месяцев назад

How did you handle room for the bottom dust collection outlet for the table saw ?

@zakmikati Год назад

Nice and strong

@MWAWoodworks Год назад

Yup

@mattmccullough8783 3 месяца назад

Have learned a lot from your videos and putting to good use. Nicely done. But how many of us has access to a CNC tool? Would a heavily waxed wood surface work against wood glue adherence? Thanks!

@MWAWoodworks 3 месяца назад

More and more people have CNCs these days! Regardless there are other ways to accomplish it. I've explained it already in other videos 😁

@JJPetro Год назад

Very nice project. As a fellow woodworker, I am convinced we spend most our time building nice projects for our shop rather than use our shop to build nice projects for others!! 😁😂 I have often wondered when I finish building all of the shop projects I think of, what will I do then?!?

@MWAWoodworks Год назад

I can tell you for sure people enjoy watching my shop project videos WAY more than when I build something else 🤣

@kenhorner4023 Год назад

This is great, and I plan to build this or something very close to it very soon. Thanks! One question though. I too like the idea of dogholes in the laminated top, however I do not have a CNC. What would you recommend as the cleanest way to bore these dogholes without getting tearout in the laminate?

@MWAWoodworks Год назад

There's a link in the description for a product called the parf guide system for creating mft style tops by hand (with a drill)

@kingbamafan Год назад

Nice build. I can see several influences incorporated which is my favorite way to build anything. Are you still able to source BB? It’s getting really scarce in my area.

@MWAWoodworks Год назад

It's getting real hard to get actually BB. Shipments come in and are sold out asap. Have to get lucky and call ahead for information sometimes

@b.lemire7453 Год назад

Great job and a great video. I'm curious though...approximately how long did it take you to make this? Thanks!

@MWAWoodworks Год назад

Maybe 25 to 30 hours of work

@directive5147 4 месяца назад

I really like the workbench you built. So much so, I am looking at purchasing the plans. I do have one question though. How are you mitigating the dust, glue, and other debris that falls into the dog holes from getting into the drawers?

@MWAWoodworks 4 месяца назад

I dont do anything to mitigate it. I'f I'm doing a really messy glueup I have silicone mats that I put on the table. Every once in a while I vacuum out the upper drawer, maybe once every 6 months

@RichardRecupero 3 месяца назад

When you routered the slots my jaw dropped. So messy. I hate routers

@davidvastine3212 Год назад

Awesome video and table! I purchased the plans from your site and plan to build your table for my shop. Question, what millimeter settings do you use on your Festool to get the 3/4 insets for the aprons on the legs?

@MWAWoodworks Год назад

Don't remember exactly but what I did was measure my plywood in mm with a pair of digital calipers and then added half the thickness of my apron (1/2") which should get you around 30 or 31 mm. Variance in plywood thickness will be the determining factor

@davidvastine3212 Год назад

Thank you for the info and help! Do you remember what size and length dominoes you used?

@briancavataio1525 Год назад

How about routing grooves in between the dog holes for track clamps? Gives you other options for holding down your workpieces. Something similar to the new track clamp work bench Woodpecker came out with.

@MWAWoodworks Год назад

You could do that. Probably reduce the number of dog holes otherwise there won't be much actaul table top left lol

@davidvastine3212 9 месяцев назад

How well does a 3/4” top function for dog holes? Is it thick enough to hold clamps in the holes?