Woodturning. You'll never believe what came from this!

Glenn & Liza Teagle Woodturning & Carbide Chisels

Подписаться 9 тыс.

Просмотров 2,5 тыс.

50% 1

You'll never believe what came from this!
To buy any of my Carbide tools or cutters visit my website;
www.ukwoodcraftandcarbidechisels.co.uk
www.buymeacoff...
Thanks for watching.
#Axminster 1628 lathe.
#wood
#woodturning
#carbide chisels
#Pine
Please Note;
These videos are meant for the purposes of entertainment. Any attempt to imitate or copy what I do must be done at your own risk. My practices may not always be correct or the safest for you. I strongly recommend that you find your own way of turning. You are responsible for your own safety while woodworking. Read and understand the operation and safety manuals supplied with your tools and machinery to ensure you are safe while using such equipment.

Опубликовано:

26 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@stevenr7003 3 месяца назад

I wanted to thank Y'all for the video's! I learn a lot from your video's I thought I knew how to uses a lathe but the more I watch the more I learn and uses it on other projects I've been trying inside out carving lately turning out some nice carvings so once again thanks!

@glennteagleofukwoodcraftca5308 3 месяца назад

Thank you Steven. Glad you are enjoying the videos and have found them helpful. Happy turning. Glenn & Liza

@sandiekelley8513 2 месяца назад

could cut a bit of spongy stuff with thin 2 sided tape to get that sanding bit so your fingers were not to close to that spinning shadow and still have some small pressure.

@glennteagleofukwoodcraftca5308 2 месяца назад

Thanks for watching.

@alangibb3100 3 месяца назад

Glenn & Liza that turned out really smart your wee candle holder.

@glennteagleofukwoodcraftca5308 3 месяца назад

Thanks Alan

@joediberardino4419 3 месяца назад

Awesome

@glennteagleofukwoodcraftca5308 3 месяца назад

Thanks Joe. Glad you liked it.

@robcarroll255 2 месяца назад

I wish I could buy your carbides in the states particular California

@michaelwillson6847 3 месяца назад

You sure your not some kinda devil wizzard although new series for you to run challenge glen 😁😁 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

@glennteagleofukwoodcraftca5308 3 месяца назад

I've already said if anyone wants to challenge me, but no one will take up the offer.

@michaelwillson6847 3 месяца назад

@@glennteagleofukwoodcraftca5308 what does that tell ya. There's 1 a think I've seen online that could stand against ya although a don't no what to look for but he seems good IMO. A did more mean viewers set glen challenges but maybe you need to stick it back out there anyone wanna challenge ya???

@glennteagleofukwoodcraftca5308 3 месяца назад

@@michaelwillson6847 I've done a few challenges myself, but only a few have taken me up on doing them.

@michaelwillson6847 3 месяца назад

@@glennteagleofukwoodcraftca5308 I don't think am at the skillset to challenge but I like the turn something with just 1 tool challenge

@glennteagleofukwoodcraftca5308 3 месяца назад

@@michaelwillson6847 Good to know what each tool can do. That's how you learn.

@trahtrebor 3 месяца назад

Interesting how loose the piece was when you finished it. Id have thought you couldnt do that without throwing the wood. Nice!

@glennteagleofukwoodcraftca5308 3 месяца назад

Gentle cuts is what you need. If it comes off, it comes off. It happens. It happens to everyone. I will always show when things don't go as planned and how to rectify it. Most people just cut the bad bits out. It's from those things that you learn.

@haroldmartin8009 3 месяца назад

Hey Glenn where is your tool rest that you use available or did you make it??

@glennteagleofukwoodcraftca5308 3 месяца назад

Hi Harold. I made mine. I make all of my own stuff.

@haroldmartin8009 3 месяца назад

What type of steel did you use ? I'm a welder by trade and want to make myself a 2 inch rest and a 9 or 12 inch rest buy I don't want to replace it all the time from Knicks and dents and such

@glennteagleofukwoodcraftca5308 3 месяца назад

@@haroldmartin8009 As a Welder you would know what steel is better to use, that won't get knicks and dents.

@haroldmartin8009 3 месяца назад

I do and there is many different t ones I figured a tool steel or drill rod but it gets expensive Quickly depending on steel grade and properties I was just curious to what you used not trying to aggravate

@glennteagleofukwoodcraftca5308 3 месяца назад

@@haroldmartin8009 Not aggravated. Just don't like to say to use something just because I'm using that. You use what is best for what you want it to do.