Worker Harrier: 300fps Best In Class Pro Nerf Sniper! 

Find the Worker Harrier here: www.frontlinefoam.com/product/worker-harrier-blaster?sld=8 1.6 Upgrade Spring: www.frontlinefoam.com/product/worker-1-6x300-swift-harrier-baize-spring?sld=8 Find the CNC Metal Plunger here: springblasters.com/products/high-grade-replacement-plunger-for-harrier

Been in the hobby since 2006, so cool to watch the arms race evolve from Longshots and Doomsayers to this

Another sick quality review. Been waiting a while for this one, and was worth the wait.

Nice review. Thanks for the info on the metal plunger.

Boy have I been waiting for this video

In airsoft we weight the pistons on our snipers and AEGs to get more power out of a spring with a certain weight of BB, which the Nerf community seems to not know about. We usually wrap our pistons with solder, glue, and heat shrink and chrono until we lose FPS. Maybe be worth a try, but you seem to be getting a taste of that with that metal piston.

I had a dream where I got this for Christmas. Easily amongst my top 3 best dreams ever.

Y’know it’s gonna be a good one when the video starts off with a sniper tower clip

Great stuff

So many people running the Harrier in our Brisbane Wars. Easy to see why.

Nice review as always mate…..I’ve got to get my hands on this sabre plunger rod…..wish I could get the full Sabre M20X but the Harrier is more than a worthy substitute, few more Marvel statues to sell before I get one of those 😆

You're spot on with the interesting observation about heavier plungers there Mr P; when the plunger in my brassed Sentinel broke at the point where the catch caught it, I had to hand cut and fit an aluminum piece to fish onto the end of the pl;unger and fix it. On a cut down length of worker 28n spring the fps when up from 170 to well over (200, depending on dart). Why? I think it's the momentum of the heavier plunger being able to KEEP it's velocity as it compresses the air in the plunger tube. One thing i may get round to doing is to test sealed breech springers I've had for a while, (Retal and Falconfire are prime candidates), and see what adding weight to the plunger does to fps. Maybe just duct-tape lengths of aluminium rod around the shaft of the plunger in 10gramme increments?

The one thing the swift has over the harrier is priming at higher spring loads, the swift has a longer prime making it easier to prime higher spring loads, everything is much better though

Using this for school nerf war, sniped my target from the opposite side of a parking lot, thing is insane.

Nice review Bradley, Harrier is awesome so much easier to prime than the Swift with similar upgrades 👍

Interesting that you encountered so much difficulty getting one into Aus. I know Blastertech has had them since March or so when I got mine. Great review.

I like the bolt prime especially for heavier spring loads. I do however just have the bolt threaded through the vertical foregrip so I have the option of bolt and pump priming.

Yo Bradley, not sure if requested before, possible to show an 30m accuracy test for the Harrier on a bcar with the top 2 strongest springs (250 and 300), on the 450mm aluminum barrel available for the Harrier? As for the bcar, you may use the one fitted for the 300 fps Storm AEG review or any bcar you find that works best for the Harrier. Thanks!

My harrier only gets near 300+ with the 450mm barrel and that 1.6x300 spring, so to get those numbers on the 365mm barrel I definitely think the sabre plunger rod provided some help.

nice vid, Bradley. Could you make an update on accuracy using a better barrel?

Hey mate, Order a harrier today. It will probably arrive next week. Fingers crossed. I also ordered the 300mm spring. I've been looking around, and I became curious. I was wondering if you might be able to do a couple of tests. I was thinking, What would happen if you put a 1.6 or 1.8 350mm spring from a worker swift in the harrier. I'd assume that a sabre metal plunger and catch would be required as well. I reckon 350fps wouldn't be out of the question for the harrier, provided it can withstand the punishment. Thoughts?

Amazing review man! I picked mine up in the US two weeks ago and have seen some crazy improvement with a 16mm BCAR that i found on thingverse. It's pretty insane.... Where did you get the 300 FPS spring?

Finally got the money set aside for mine, arriving tomorrow. Took a year but i gotbtonlet everyone else destroy theirs through trial and error first so i know what setups to go with

Ive got the saber metal plunger and catch With the 450 barrel and 1.6 x 250 spring And i don't know if im breaking the 300fps mark.

I want a montage of clips like the first 20 seconds.

i would just like to point out , I have a harrier and with a scar ballerel and stock ballerel ,the iron sights are very accurate ,but yes you do have to shove your face on the stock

Can you make a comparison of all your 300fps snipers?

Also I’ve got the big spring and big barrel and have shot maybe 50 times and still haven’t had a problem with the plastic plunger so maybe the fixed the issue 🤷‍♂️

Can you recommend a good budget scope that I can use with my new Harrier and possibly my Seagull?

Do you like this more than the Bradley Phillips Caliburn?

Great vid. Got this blaster added to basket while i look around a bit more. My kid wants an accurate sniper blaster with a scope + scope camera ( so he can show off his hits ) so he can shoot targets in the field outside our house from as far away as possible. I dont know anything about blasters and even less about where to start with the scope camera thing. Any suggestions? ( we are in the UK if that Makes a difference )

Oddly enough, I have been having seal issues with the harrier recently. I used it for about 2 months with no issues, but recently, some darts have way lower velocity, and the blaster makes an odd "pthoo" noise when firing. I tested the seal and it has about a minute seal, which is odd, and the darts I used were new worker gen 3+ darts

Just wondering how low you can go with FPS on these? I enjoyed your video on the Sweetheart Storm getting down to 100fps. Would it be possible to get a Harrier under 160fps?

whats the red dot sight you use in tis video ? also I have the same numbers with the same setup except still original plunger, sabre one is in the mail

How is the stock catch holding up against the Sabre plunger? i made the upgrade recently too but haven't seen any particular issue with the catch

Out of curiosity what sight are you using for your harrier setup? Been looking for a good optic for mine

What vertical grip are you using? 4:35

The decorative barrel cover is for the 550mm barrel and leaves room for a bcar

Hi Bradley, how would you compare the harrier and Kirin in terms of build quality?

Hi what is the size for scope railing on top? Is it 20mm or 11mm? And do you suggest to change into metal plunger?

6:41 If you're using the longest barrel you can still fit the scar attachment.

Just got my Harrier on Friday :) Are you still using the worker adjustable riser?

Bp i luv ya mate❤.... thank you

are these high powered nerfs legal in QLD like gel blasters?

Hey Bradley I been watching you for a while, I was wondering, if i want to buy a more powerful blaster than a nerf, would you recommend me getting a dart blaster or an airsoft blaster? And which model would you recommend?

Hey! Nice gun! Just a question, Do you know what the scope you have is?

Hey mate just wondering what the max distance you could comfortably get hits at with this blaster?

fill the gap in the plunger with A-B glue .

I got mine on day one and i am absolutely loving mine. Sold my swift to get it. I am getting the same numbers as you and im using the stock plunger tube.

Feeding the algorithm

So i got into this youtube-funnel trying to explore which nerf gun could replace my broken one. I used it to play with my cat as it doesn't shoot that hard and my cat loves it. I dont think this is the route I should be taking.

I’ve tried heaps of barrel and spring combos. I’ve settled in the 450mm barrel a 1.6 300 spring with a 20mm spacer. Average with bamboos is 305fps Dragon darts up to 330fps I’ve used it in Sydney Nerf events. Anything 30m is point and blast I bought a Baize at the same time , obviously it sits in the corner. Soo many upgrades needed😢

My Worker Harrier air seal lasts about 10 seconds with the "hand test". Is that an issue? Should I return it, fix it or not worry about it? I'm new to the sport and have no way of telling if it is affecting performance.

I was considering getting a Harrier, but honestly the few quality of life features it has failed to distract me from the fact that Swift is still stronger. I run the 1.8 setup, and so far Harrier just cant compare. I might just wait for Worker to make another springer and see if they make an actual upgrade.

CAN YOU GET A MORE POWERFULL SPRING. 350 FPS

365 mm barrel?

A comparison with the swift would have been a nice extra in this review.

It's strange how your Harrier came with thumbscrews, no one else I know got thumbscrews, instead the crappy worker screws haha. Also good call with the Sabre plunger, I'll be picking one up soon, also, the metal roller catches and mag releases should be coming in about a month.

Which is the best bcar for this blaster ?

Brad, I thought you said chronoing your blaster without a SCAR was cheating XD

Going to trade in my SIG spear for a Harrier. Worker QC > SIG QC. 😂

BRO AWESOME VIDEO. !!! I WANT TO BUY THIS GUN JUST FOR IN-HOUSE USE. SHOOTING TARGETS AND HAVING FUN WITH MY SON. WILL THAT BE GREAT YOU THINK ? THANKS ALOT FOR YOUR VIDEO

Would anyone run a trion over a harrier?

What do you think is better this or the dzp mi 4.0

Maybe one day Aus gov will make all nerf dart blasters Cat. A firearm lol

Where did you get your optic?

YEAHHHHH

i just got the sabre plunger and found no real improvement with it.using the 1.6 and 365 barrel im only getting a max of 272 with the avg of 265 with gen 3.

Hi bro, may i know what scope u using on that blaster n where can I get it?….

Honestly as an Australian I could just make my own springer for cheaper.

you should do more 3d printed reviews

Its not the rifling not imparting enuff spin on the darts, its the bamboo darts ur using - the groove sections are smaller in diameter therefore string n bearing scars sometimes cannot put enuff pressure on those sections. Worker bamboo darts also wear out alot faster compared to worker normal ones due to the thicker sections getting wear out/thin out faster resulting in very erratic accuracy when using scars bcars. Will have to replace ur worker bamboo very frequently if you use bscar/scar to prevent accuracy loss over time or make sure ur bscar/scar r not the optimized types in the amount of pressure it puts on the darts.

Next Australia will ban silverware and you'll have to eat your food like a dog on the floor.

First. Reeeeee!

buy a 3d printer