#withoutanyDoubt #TruckWithoutaLeafSpring #amazing You've never seen Young Man Build a Truck Without a Leaf Spring || without any Doubt Amazing Process #amazing #TruckWithoutaLeafSpring #withoutanyDoubt #massproduction
The leaf springs are there to provide flex under heavy load and to stop your bones being rattled out of your body. The ride will be so bad when the back is loaded up you'll want to go back to the original springs!
you can go back to original springs only if your truck's frame stay intact. without springs a lot of parts of the chassis will fail under stress and fatigue
Yo creo que. 1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla. 2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018. 3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado. 4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente. 5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖.... 6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius) 7. No hace falta doblar los electrodos. 8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos. 9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil. 10. You can create a template or pattern to make the bevels with oxycut
Depends on where they're going and how fast. Huge agricultural tractors have zero suspension not even the air in the tires as they're usually filled with a liquid to give additional weight for traction. Yea if the ground is uneven and you're going at any speed they will beat the hell out of you. But smooth ground they're ok.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj
@@nonconformist3039 Не логично, когда пакет как у пакистанцев то это тупо становится балкой, усилие идёт на ось балансира и далее на раму, после чего видим ролики грузовиков на боку и "тапочки" варят балансиры и усиливают рамы. Я 15 лет в дальнобое проходил, и все эти перегрузы зло. Хозяева "тапок" убивают их на производстве, а в ютубе куча лайков какие крутые тапки))))))). Тфу, сидят в говне по уши и лыбы дарят, типа всё ништяк ))))
@@griggs310 лайки ставят не за то что круто, а за то что прикольно - делают глупости но данная дичь развлекает. Ремонт наверно у них дешёвый, поэтому перегружают. Типа экономически обосновано.
It's a walking beam, and it's common in heavy trucks. Add some brackets and rubber cushions (circles of rubber, cut from old tires) to the truck frame to stop the beam over rotating, and you'll have a simple, very heavy duty rear suspension.
Yo creo que. 1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla. 2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018. 3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado. 4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente. 5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖.... 6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius) 7. No hace falta doblar los electrodos. 8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos. 9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil. 10. You can create a template or pattern to make the bevels with oxycut
Maybe if they stopped overloading their truck they wouldn’t have to weld up a solid suspension. Not that this is gonna help, just gonna make it even more dangerous.
@@Paul-iu1omгрузовик больше ждет та же судьба, его будут перегружать еще больше и следующее видео будет о том как убирают рессоры уже на большом грузовике😂😂😂
Yo creo que. 1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla. 2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018. 3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado. 4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente. 5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖.... 6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius) 7. No hace falta doblar los electrodos. 8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos. 9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Hard to say with the way he built that one, but, current 70-120k 6 rod style susp has the option of springs or a beam styled like that one, that acts as the spring as well. Very common on heavy bed units with planetaries. However they do use a rubber trunnion bushing on them., I can't see where they put anything like that in there for sure, appears to be steel on steel?. Drilling thru the frame flange is a bad idea on a good day. Guess if he wants a cheap susp, he got one. Like to see it again a year or two down the road. Be a fairly constant same old battle with wear on the axle seats, just like he had with the springs, no wear pads on axle or beams. And I'd bet his frame and or the beam has cracks shortly too.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
The reason they upgrade the suspension on these trucks so much is because they overload them. They go way past the weight rating on these trucks, seen lots of cracked frames, axles, and broken suspension from these Pakistan and Indian drivers.
Жёстко однако, ни рессор, ни стремянок, ещё мосты усилить конкретно и просто железные колёса и будет тачка огонь, хоть по 200 тонн грузи на каждую ось. Земля главное чтоб держала.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
This was going on all over the world when men worked and repaired the trucks where they broke down. Unfortunately by the time all the Professionals get their cut, theres not much left to cut so the truckers, fitters and ironworkers have to bear the brunt. After this "when they have so much money,it no longer matters to them" the greedy pigs will give the hauliers a choice. Go into debt to buy new plant and keep within the regulations. Then you can put 10 or more of these men on welfare . These are gifted and talented men, the kind of men who are invaluable when all the false plastic trash, falls to bits.
This method is Excellent! This is called the hard bar! Used for Extreme Duty Applications! The truck chassis frame or axels will fail! Solution is stop the overloads! Hey driver you better install air suspension ride seats! Remember money is the evils! But do in for The Lord God! Love your brother.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Only 15 minutes in and I already seen continuous weld, proper use of welding shield and even caliper… think those might be foreign spies after Pakistani technology secrets 🤣
Следующим этапом будет рама как у экскаватора. Жёстче чем у бульдозера. Потом ось лопнет - поставят с вагона железнодорожного. Тормоза не держат - уберут вообще. Будут тормозить об другой авто. Идеи даром, пользуйтесь.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
If you remove the leaf spring and install the support bar, Failure to cushion the impact may cause the axle shaft to break. I've seen a lot of videos on this video where a truck's axle shaft is broken and repaired.
Yo creo que. 1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla. 2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018. 3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado. 4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente. 5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖.... 6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius) 7. No hace falta doblar los electrodos. 8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos. 9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Заводские инженеры - дураки конечно! Вот пакистанские ребята - красавцы! Действительно, зачем эти ненужные рессоры...только максимальную грузоподъемность ограничивают...подумаешь в следующий раз рама треснет, они и ее заварят!
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Uma coisa incrível que sei que é rentável, mas aqui no Brasil seria difícil de acontecer, muita burocracia negativa aqui An incredible thing that I know is profitable, but here in Brazil it would be difficult to happen, a lot of negative bureaucracy here
Yo creo que. 1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla. 2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018. 3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado. 4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente. 5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖.... 6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius) 7. No hace falta doblar los electrodos. 8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos. 9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Great work and a good idea. 😅 I saw mechanics wearing work boots? Is that not against the law?😂😂😂❤. A prestressed box girder and free floating tires. The male Karen's are jealous. 😂😂😂.
If it isn't overloaded i think it will be just fine. leaf springs are difficult on an incline, i have almost turned over a trailer on two occasions, both times in a field, due to the lower wheel sinking, and shifting the weight onto the lower spring. This looks like it will be quite stable.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Did anyone else notice that in the beginning the truck had 4 wheels per side and in the finish product, it had 2 wheels per side? Did the truck go from heavy duty to medium duty?
This guy right here knows what he's doing when it comes to welding I've seen them well shit that shouldn't be welded crankshaft camshafts blocks all kinds of stuff rear differentials all kinds of stuff he is a talented Machinist..... 😮😮😮😮😮😮
I don’t think that over half of what they do is safe and sane. Not is it up to code. I do believe that they are hard work, creative and do great work given their education and training that they have been given.
Hendrickson makes soiled mount suspension just like that for mine trucks that haul extremely heavy for short distance on relatively flat surfaces. If you install a solid suspension like that on trucks that will be used on roads or uneven terrain, you'll going to rattle your teeth out of your head after you've bounced your head off the roof of the truck cab. Say goodbye to your spine and kidneys as well !!! 😅😂
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Literally seen this like 5000 times it’s called a walking beam suspension every cement truck in the world or log truck has one. What the fuck are you talking about?
That bearing definitely gonna fail in a short time. It was installed dry, then coated with grease on the outside. It doesn’t have a rubber seal to keep out dirt, sand, etc. And no grease fitting to grease it over time.
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
Молодцы!!!Рукастые мужики!!!!!Теперь я понимаю почему континенты на земле удаляются и появляются провалы в земной коре!!!Скажите водителю пусть много не грузит,а то точно земная ось может не выдержать!!!!!😂😂
I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut
@@Mechanicalact His frame will crack with the way they attached it, beam or hangar will likely crack around the welds, hard to say which one goes first.
