Yukon Ultimate 88 Install - Ford 8.8

Подписаться 3,1 тыс.

Просмотров 3 тыс.

50% 1

Installation of the Yukon Ultimate 88 kit for the Ford 8.8" rear axle that is swapped into my Jeep Wrangler YJ. C-clip eliminator and chromoly shafts in one shot.
Parts & Tools-
Ultimate 88 kit - amzn.to/3Lp9yTo
Slide hammer - amzn.to/3mMxR3B
Rear axle bearing pullers - amzn.to/3mJNPvg
8.8 Spartan locker - amzn.to/3mFyXy1
8.8 Solid diff cover - amzn.to/3l4vYPl
USA made torque wrenches:
1/2" - amzn.to/3J9UiY2
3/8" - amzn.to/3LkV4Ea
I’m an affiliate marketer with links to an online retailer and receive commissions for purchases made through these links and affiliated sites.

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@PaezEddie 3 месяца назад

Awesome video! Doing this on my 76 ch7 8.8 swap

@PaezEddie 4 месяца назад

Thank you very much for the detailed video. Was worried about tackling this on myself- picking up the tools and going to hit this project next weekend

@HardEarnedBacon 4 месяца назад

You got it!

@maxrogers762 Год назад

Good to see ya back! I'm in the middle of an 8.8 swap so I appreciate ur content. Congratulations on yalls baby! We jus had our son 2 months ago, so I'm right there with ya

@HardEarnedBacon Год назад

Thanks congrats to you too!

@danhambrick6331 Год назад

Nice job.I bought this kit for my 8.8 that I am building for my Jeep Cherokee.I was just going to buy the axle shafts but decided to go with this kit instead.I have a Eaton TrueTrac and 4.56 gears that I am installing also.

@HardEarnedBacon Год назад

Thanks, I'd like to build another XJ at some point and would do TrueTracs again too

@danhambrick6331 Год назад

I have the TrueTrac in the rear and A Yukon Grizzly locker in the front....

@cerberus45 10 месяцев назад

extremely helpful video, I'm doing the same thing - the visible machined surface on the end of the shaft after pressing on the bearings would've thrown me for a loop. Thanks for sharing!

@HardEarnedBacon 10 месяцев назад

No prob!

@rl1106 Год назад

Great video! I'm in the middle of a 8.8 swap as well. I would like to do this mod in the future, but for now its going to be 8.8 posi 4.10.

@HardEarnedBacon Год назад

Thanks! Trying to find the time to finish my regear, about halfway done.

@jk_wrangler13 Год назад

Lots of har work, but it will be worth it in the long run. Congrats on the upcoming baby

@HardEarnedBacon Год назад

Thank you!

@jk_wrangler13 Год назад

@@HardEarnedBacon you're welcome

@waterboy9036 Год назад

Great tutorial, thank you! Does the shaft require a slide hammer to remove it if you need to do some carrier work?

@HardEarnedBacon Год назад

Thanks! I pulled them out after this video was done and I did not need to use the slide hammer. But they may be a little more "sticky" to remove once they are installed with the RTV.