This is an educational channel that aims to educate people interested in CGI, I am Firas S. Noori, a lecturer at Ajman University - UAE, and I use this channel to upload some tutorials for my dear and precious students to help them learn easier.
Firas S. Noori Lecturer at Ajman University - UAE M.Des. Sustainable Architecture - University of Sydney M.Sc. in Architectural Engineering - University of Technology
I cannot express enough how great these videos are and a question came to my mind: how could I place the Text in the centre of the room as the text's base point is in the top RH-side.
Hi dear, thanks for your kind words, in the text entry around 1:30 you can see the options in the "Paragraph panel" choose the middle and the text will be appear exactly at the center
@@FirasNoori My pleasure. Thank you so much for your anwer. I'm sorry for not being specific as I was hoping to place text in the centre of the room using Move>Specify basepoint (it only shows a point that says MText Location in right top corner)>Mid between 2 points. The result is that the text is slightly off centre towards bottow right.
I've got a little question about the door leaf bottom line. In the instance of single door they were not drawn but in case of double glass door they were. It would be lovely to know if it matters. Thanks.
Hi dear, I was trying to show more options in one video. Sorry if it confuses you. In the single-leaf door, I was trying to show the one sold leaf where no glass is needed, and it is a simple rectangle inside the frame. In the double door, I was trying to show the other case where you have a door frame, then inside it the leaf, which also has a frame with a glass panel inside it.
Thanks for sharing this video, especially from end to start technique. Just one suggestion that you can add tags or edit title to make this video searchable and visible in RU-vid. Because I was searching for "How to make rooms/room walls in dynamo? But in the result I used to get irrelevant videos of room from already existing sketches.
thank you, the video is very helpful. little question, how can objects automatically rotate according to a line? for example, making a box object and the object can automatically rotate to face outside
Depend on what are you arranging! If you ate array dynamo geometry then the answer is yes; if you are array revit element then the revit family element must be point base family which will make the answer also yes; if you are using level base family, or wall base family then the answer is NO
How come all finishing layers (front and back) have the same value? Wouldn’t you expect the volume of the layer at an inside to be slightly smaller than the layer on the outside of the wall?
Dear pro, how to solve the problem of me? If the grids I create from number 1 the result I got from number 2 and the gridline I started from letters A I got the letters B.
Hi, make sure in dynamo to change the level to the one you want, second, make sure in revit you have more levels already created, I.e level 2 and 3 and 4, so if you choose level 2 in dynamo it has the level in revit to comply with. Also check the column method creation , if it is based on giving a fixed height then all good, if it is based on the provision of both lower and higher level as constraints, then the issue is a bit harder as you need to provide both lower and upper level in revit, try and tell me Cheers
@@FirasNoori, Thx for fast response, I use Your script (part) for place column in grid intersection, from above. Levels node change levels and elevation but revit change base and top offset to minus and columns is always on level 0.
السلام عليكم دكتور وياك اخوك مهندس كرم من العراق خريج جامع التكنولوجيه واتمنى من حضرتك استاذ لو تكمل لنا هذه السلسله . حقيقه كلش محتاجيها ماكو واحد مثلك يشرح حقيقه باليوتيوب على وقت فراغك حتى لو محاضره كل اسبوع وتكون الك صدقه جاريه. شكرا لك
سلام والرحمه، اهلا وسهلا بيك، اسف عل تاخري بالرد، واتمنى ان الكه الوقت لاكمال هاي السلسله، مع الاسف شغلي زادت عدد ساعاته، وكم المسؤوليات اصبح اكثر وأصعب ولهذا قل عندي الوقت للنشر عل يوتيوب، حته الي جاي انشره هو غالبا اله علاقه مباشره بالدروس الي جاي ادرسها بالجامعه، انشالله بالمستقبل اكمل هل سلسله والك مني كل الاحترام والتقدير
hi, i am struggling with setting my Site Plan which is in meters, to put it in layout with a 1:100 scale. When I turn the scale on 1:100, it views the entire context plan (which is huge) and site plan is supposed to only show building and surrounding area. so how do i fix that and make the 1:100 scale work? Please help, your expertise is needed.