For am4, hindi po. For intel, pwede, pantay po kasi yung distance ng butas sa Intel.

Sorry for not meeting your expectations

Hello, sorry I wasn’t able to test that

For 78x3d, yes. Can’t say for 7950x.

As of now, no idea yet. I will test zotac soon though.

Sorry, I don’t have any. You can likely diy the insulation though or maybe add lots of electrical tapes to make it sturdier

Ok lang po pero monitor temps

“Standard” is 185mm. If you have a bit longer, like yours at 200mm, it is usually fine but there will be some bulge, you just need to tuck it somewhere.

Full load 250-ish watts. Can’t say malaking malaki, pero bigger than what we usually use sa bahay

Rtx 4060 po

@@manongunboxing 18-20k po 4060 sa shopee

Wala na po kasing 15k now. Bale rx 6600 po at 13k tapos rx 7600/rtx 4060 na po. Ang nvidia counterpart ng rx 6600 e rtx 3050 kaso masyadong mahina vs 6600.

@@manongunboxing okay po, ang exact budget ko po kasi is 285 usd which is 16,671.93 in pesos po.

No. Not that rich to try lots of ram. But this was the only board that had issue. Some who commented on the channel had issues as well

Yes, but the official space for that will take up gpu space. You can however tuck it under the motherboard or under the PSU

@@kuyamoarf I could get KingBank DDR5 6400 ran stable at 5800 only

@@Oakyman yeah same, now it's not really stable at 6000 so i set mine to 5800 also

Hi, yes definitely in the pipeline but availability is bad here. Hope the availability is better towards the end of year

Hello and thanks for watching. While I don’t have the GPUs, based on exp, GPUs of the same class will perform with unnoticeable difference to the naked eye (+/- 5% diff). Oc variants are usually 3% better than the base models though, thus asus dual oc / eagle oc could be 3% better but still unnoticeable.

Other than xmp, I test in vanilla for all cases.

Bale nakausli yung cooler tapos may fan pa sa ilalim? Di kakasya sir

I believe this is around 200mm. But, the riser hole placement is also different than usual.

Yes, intake. But you can reconfig to exhaust if you really want to

@@manongunboxing will I get better results than with the ID cooling 47 paired with noctua A9 25mm?

@spacedandy6778 while I don’t have results, in theory, axp120 will do better (on average). In theory, the heat will fill up the mass of the heat sink and it will be cooled down by blowing air thru it. Thus your limit here is the mass of the heat sink and the fan removing heat from it. While there are other factors such as heat transfer rate (heat pipes doing their thing), I think for is-47, the mass is too small. And thermalright isn’t just a cheap solution, it is cheap and good solution.

With Davinci Resolve, yes. With Adobe, not sure

With my G.skill, it wasn’t able to do so.

What RAM are you using?

Good for you 🙂 I’m not so lucky and for some as well.

Almost the same specs as my build. 6400 32cl XMP. curve opti same -30 , 7600X ES. Only issue is sleep. It wakes up or starts like from off state. mouse/kb no go. Only start button. Not a major issue. Got 32GBDDR5, 7600x Engineering Sample, and this mobo -all for less than $400 (365 USD actual), can't really complain.

Good for them 🙂 Hopefully jginyue will publish the tested RAM in their site.

Even known brands have problems.

@@junlp9492 That’s true. But they’re more reliable and last longer than Chinese brand.

Thats a different board though. And its issues didnt get fixed for 1 year from release lol

i do this into my RX 6600XT MERC 308, and works !