I went to the url for sub parts in the description and it took me to a spyware page direct Apple iPhone support scammers in India . Idk if there is a good working link to get subwoofer parts from if there is please lmk .
I have a few gems laying around a Rockford power hx2 15” with a bad coil a 12” earthquake San Francisco 1990 competition sub fully functional . A Rockford power hx2 12 with a broken tinsel lead . Another Rockford power hx2 with a cracked basket Also have 2 12” Cerwin Vega 12d4 originals and a Vega 10d4 . I’m looking to do something either repair them all or improve them if possible like the HX2 I know there’s better options for tinsel leads . I’ve never repaired any speakers though so I’m not sure where to begin .
I have a question....I recently was sold one of these 15" silverbacks lloll and its failed up is it worth it to rebuild it or chunk it as a loss and keep on learning...I only give $30 for it and the rubber looks great just voice coil is trashed.....let me know what you would do....thanks a lot
Nice video dude , i work in restoration , car audio as a hobby. The reason i commented is i work the disaster relief for Hurricane Harvey I was there in Texas helping everybody for like a year and a half. Rebuild . Nice to have found your channel.
The original Juggernaut was a DD OEM. Subsequent ones were cloned in China for MMATTS to reduce cost. Thanks for the video. What u up to nowadays? Time for a new video pimp.
Hey dude could you rebuild a Kicker C10? It was frozen when I got it. But I did the drop it on it's face method to get it unlocked, not the coil is scratching/rubbing.
It comes with a high quality low tolerance resistor because it matter most in calibration...you want your calibration to be as close to spot on as possible for accurate measurments...if it came with a 10% resistor instead of a 1%...all measurements would be off by that much...pretty big difference
Thanks for this video. I have done a ton of recones DC , Sundown but never have built one from individual parts well all that will be changing. My biggest question I have for you is will it be easier to build a recone first or build it in place after I get the ring ca'd below the spider and triple joint done.
Well that sucks I just threw my two Kicker CR-V because this guy that is well-known( EMF speaker guy)on another Channel told me that it couldn't be rebuilt and i should just throw it away! in the comment section haha I held on to those speakers for like 2 years after a stereo shop had blown them with a bad amp installation along with the dd dm 2500 amp
I am new to reconing speakers and I have watched 100 videos and nobody has broken it down like you and actually explained it the way you do and make it easy for anybody that can read a measurement
I dont know your name but thanks a lot CMD Audio. With all the information you provide and what mesurements are needed I was able to mess up a sub and then compete 2 others after. One is still running strong and I blew up the second one I built. So I'm back here again for a refresh course since I need to build this one a third time 😂 this time I'll try to actually follow your directions and build it like a drop in. I was doing it spider and coil into the basket first and if was aligned great then when I put the cone on it pulled to one side a little bit. Just wanted to thank you for this amazing peice of teaching gold this video was.
Hi... is it possible for me to use the magnet and basket of a midrange speaker to build a 5 inch subwoofer..? If so please may you assist me.. I have very little experience,, but lockdown has made me ambitious..
I know this is an old post but your math is off. X-Maxx is calculated by how far the speaker will move with the windings still in the gap with a 2-in winding height and 1/2-in top plate you will have 3/4 of an inch of X-Max one way or 19.05mm
hi please >>> can you tell me what is the exact position for the voice coil inside the magnet like if the magnet thick is 4 cm and the coil winded wire is 2 cm thx
Hey dude i know this is a while ago but your my only help! , so if a 10" basket has a voice coil exit of 3.5" , can you have a 3" coil and a 10" cone with a 3" VCID?
I currently have 2 Skar audio TXL 18s. They have the 3.5 coils, 6 spoke baskets. I think the factory cones are the same as what you use in this video. Do you think I could rebuild them with say TI baskets with 10" spiders, with a tall or mega roll surrounds so I could get more xmax? Or would it not be worth the trouble. Just wondering. Thanks.