in your video today can you show how to please pull down the outer driver drum and your GE washer inside the front panel please? In your video today can you show how to please pull down the outer driver drum and your GE washer inside the front panel please? ?
I cut out the blown fuse and bypassed it with some wire and it did turn on the motor and agitated and spun but I am getting the four blinking LED codes error, check mode shifter coil, i’ll just buy a new washer because the part is like $250
On my model vacuum (BDASP103) there are 4 screws on the top of the motor housing that hold a removable piece of plastic. The rest of the vacuum rests on this frame when it’s sitting upright. Anyway, the belt spindle is exposed when this piece is removed. It’s still a very tight fit to get the belt on the spindle, but marginally easier than working from below. Belt item # B092DJFHW1 Good luck!
Honestly I think black and decker made it impossible to fix drive belt and you did it ! But why not clean up brush holder while you had it out. I put one in and it was a beeeaaach!! But good you put drive belt on ..th e y made it VERY VERY DIFFICULT.
My neighbors washing machine will wash and spin the clothes. It starts to act up during the rinse cycle. The water does not fill up during the rinse cycle, then it spins but does not drain. Then the machine simply shuts down. You have to unplug the machine to reset it. Which in some cases could take a few hours. Do you think this could be the thermal switch? I tried the control board with no success.
I have a question, the clips that you pop off to get the front off. Was hard to take the front off after you pop the clips? I can't seem to get pass that! Could someone help me?
I don;t understand, I mean I see the wire, I have the exact same washer, How do you know that is the wire that it's bad and where do you cut it or what section? Sorry, just trying to fix this same problem. The motor does have a blinking green light.
if the motor has a blinking green light I don't think this is the issue because when the fuse was bad on my washer ,the motor light wasn't on. Thanks for watching
I basically got a new motor,got a new lid switch but nothing worked. I new it was the problem because there's light on the motor and when the fuse is the problem, it won't light. Hope this helps.
Hi there great video...just a little confused. I'm I looking for the same type of connection that you ordered on Amazon (thermal fuse)? Or I'm I just splicing the red and white wire and attaching the " thermal fuse wire"? Thanks
sorry for the late reply. I removed the old thermal fuse and attached the new one, I did have to connect it both ends with wire nuts. Hope this helps. Thanks for watching
Dude thank you so much for this video, this is exactly what I was looking for - I replaced the lid switch which but it still didn't run, and I had a feeling it wasn't the motor, then I stumbled upon this video and I knew it was EXACTLY the problem. I ordered the part off Amazon and tried it, and it worked perfectly. Thanks for posting this video!
Hello,engineer, I have the same type of washing machine that is filled with water, but it does not work and the program works, but after filling it with water, the clothes do not spin
I would suggest trying this fix since it is a cheap fix. Mine didn't spin either and would just fill with water. The part is under the video. Hope this helps.
@@multipletidbits2301 Thank you for your interest and support for me. 🙏🌹Of course, wonderful and very valuable videos. I like to maintain things. Thank you, my dear🙏🙏
Thank you very much, . . I crawled all over that washer looking for the fuse, . I knew it wasn't the motor. I almost bought a board thinking it was bad, even though no error codes came up. . Mine was hidden behind that same black tape. . Thank you very much. Saved me $$$
i dont mean to be offtopic but does anybody know of a trick to get back into an instagram account..? I stupidly lost the login password. I love any tricks you can give me!
@Callan Kellan I really appreciate your reply. I found the site thru google and Im in the hacking process now. Takes quite some time so I will reply here later when my account password hopefully is recovered.
Mine didn't blink at all and the light was off due to the fuse. However this video show what the light means ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-aMEjN7BiGmI.html. Hope this helps.
Good morning I am having the same issue as you had but tried getting that thermal fuse you purchased and cant find it anywhere tried everything even bypassed the door switch and now have it direct but cant find the part number or correct name for the the thermal fuse (red and white cable for my washer. Please help 🙏
I apologize for the late reply, for whatever reason I didn't get the notificate. Here is a link to the fuse on amazon www.amazon.com/WH49X10055-Genuine-Original-Equipment-Manufacturer/dp/B00E1NAQMY. Hope this helps.