Dupa ce am vazut prezentarea ta am luat si eu una. Nu tocmai multumit. Este relativ grea si prost balansata iar cu acumulatoare de 4ah cu fir eu nu am reusit sa tai continuu mai mult de 10 minute. Capul de taiere(cu filet normal spre dreapta, deci nu usor de inlocuit) cu care vine in pachet are un singur fir nu doua, si este foarte slab - se rupe tot timpul. Cand bateriile sunt la 30% motorul nu mai are putere, se ineaca in iarba de doua degete. Aparatoarea este o gluma proasta(vad ca tu o folosesti fara), este prea mare in dreapta si sta in calea lamei, rotatia lamei fiind inversa motocoaselor pe benzina. Manerul cu coarne nu poate fi strans bine, iar hamul este imposibil de reglat ca sa iti vina cum trebuie. Mai pe romaneste un dezastru de motocoasa, cu baterie.
I doubt it is half as slower as 36v version because you can cut 2x30mins with it instead of 30mins 36v. The 18v vesion has 7500rpms and 36v has only 6300rpms. So my math doesn't add up with it. 1 battery version is lighter. I know because I have 18v chainsaw and it is slow but also very light to use.
Hey dear I am facing power dropping issue in series connection. I have connected 340watt and 380watt solar panels in series to epever 40A mppt controller with 12v battery. It show power of one panel when I disconnect solar connector and reconnect, the mppt show both Panels. It’s hard to do this every morning. It was fine in winter but now summer starting and facing this issue. Using both panels form 2 months. after wire disconnect and reconnect the voltage jump from 33-36 to 75v. If something wrong with one solar panel then it should not work after replugging mc4 or solar wire in the mppt after that It work whole day but same issue next morning Both panels volts amps are little different. Tesla 34.51v maxpower 33.18v. Tesla amps 11.01amps maxpower 10.29amps.
Yesterday I could borrow an MT50 from someone and found out that one of my two mppt is not read by the MT50. I could access one mppt and program it in user setting, but the other one doesn't communicate with the module as so I can not read/write from the MT50 to/from the mppt. :-( Is there a way to reset this mppt TracerAN to reboot ?
Thanks for asking. I still have the same Xiaomi M365 scooter since September 2019, with hacked software. It works great, I didn't have problems with it. The battery is doing 15km like 2 years ago. In the summer the engine is heating up more, but i use M365 Lock app from GPlay to monitor the controller temperature.
Nice video, thanks. I brought a Mi Pro 2 this week and experienced that the factory setting is really not enough to drive uphill. What I don't see why Xiaomi states that the scooter should be fine until 20% slope. Clearly not true.
Hi Marcusss K. I've used this setting for 1 year and almost 500km with no issues. I like also the acceleration response. Half of my trips are uphill. I can say that it is safe for long term, for normal drives. When it is used for long uphills, the motor (front wheel) is heating up, which is normal, but as a safety measurement, some brakes on the way can help.
Testing Everything thanks for the fast response! I will stay like that,then. One more lil question,could it be more safe as i have the m365 with 2 fuses or it has nothing to do with it?
Hi Marcusss K. I've used this setting for 1 year and almost 500km with no issues. I like also the acceleration response. Half of my trips are uphill. I can say that it is safe for long term, for normal drives. When it is used for long uphills, the motor (front wheel) is heating up, which is normal, but as a safety measurement, some brakes on the way can help.
