Gracias por compartir sus conocimientos

What about this code on an ISB engine? How do I figure it out

Que buen video podrian decirme porque tarda en despegar las balatas delanteras en un camion

Hey can you send me the wiring diagram thanks

10 de 10

I have same problem I can figure it out I inspected the head and rollers where good but one plunger was the same as his video does that mean is really bad

If the ISC does not have a scissor gear and there is movement in between the fuel pump gear and camshaft gear, is that normal or need to be tight?

Hi can you helpme i remove the tone ring for the cam and now i dont know how instal for get the rigth position

Do u have to readjust the lash if u have compresor out? My parts guy was being lazy and didnt order the gasket so I went ahead and did the cam gear lash with all the other gears besides the fuel pump until the gasket comes in, it just came to mind that it might shift teeth when i put it back in

One of the most helpful video on YT. Thank you. I’m gonna be doing my camshaft myself for the first time on an X15 and this video helps a lot.

I work for a fleet and I have an upcoming job. I gotta replace the front cover gasket. I need to pull the timing gears. I've never don't the job but I have all the info I need and I am comfortable doing it. Im just not familiar with setting the crank shaft pin and cam wedges to lock the timing in. A video would help but any advice would be much appreciated

Thx ... helpful

Explicación estúpida

Why you talking show me the truck from outside

Excelente trabajo 👏 hacen videos en español

Where are you located so I can take my truck to you

Hola buen día porque cuando piso el freno de servicio se me escapa aire por la valvula R 12

I have a comment/question. My 2016 isx 15 in apart now. The shop found the scissor gear and bushing apparently wore causing grooving of the front cover about 1/8". I'm quite sure this may have been a cause for rattling noise. My question is however is there any TSB covering this part as the motor has never been opened and has just under 700k at 596986 miles. Of course this gear and related components will now be replaced but I'm finding it difficult to get more info on this.

Love it.

In your estimation which is better the single cam or dual cam!

What happened to the follow up video? Did you replace the head or just the plunger?

What was the fuller gauge used?

Hola porque en un rotochamber delantero tarda en soltar el aire si ya se remplaso el bote

These are great videos. You should make more!

How do you check the front brake chamber 20/20 for air leaks or any fouls?

Well this is a interesting matter, knowledge helps and experience pays, thank you for Sharing, 👋👍

Why are there manuals that say the calibration gauge is 10,000? And does not speak of 4000? Thanks

Where exactly on what axle is that located so I can check mine any help please thank you

When I go owner operater in the near future I'm gonna get a peterbilt

Looks kinda hard but really its easy after the first few times

Why you didn't bought the repair kit? Intead to buy the head?

And now I know too. Thank you so much.

What if the dash has abs and traction control light on

i been trucking 10 years mostly freightliners and internationals past 2 years pete 579 the ride quite smooth seat comfy no back pain! interior is quality. As long as you regen properly do pm cummings 13 speed feels perfect. If i ever own a truck it gonna have to be a pete although i hear parts are easier to get fore freoghtloners

Can I do same retrofit on 2014 prostar ? And what type of clutch fan it is ??

Hi I have the same variable speed fan clutch and I’m trying to get the single speed one, could you send me the diagram please? And thank you!

MALFUNCTION BRAKE CONROL UNIT

Great video 📸📷

Gracias yo qiero canbiar frenos del mi nacho

👍 ur location

Hola en mi caso suelto el freno de mano y también los frenos de pies sigue el vehículo bloqueado no lo puedo mover y no ay ninguna fuga y no sé cómo solucionarlo me pueden alguien ayudar?

my 2011 international fan clutch has free play when I shake it side to side, I think the plastic inside is loose, will the clutch come off?

This video was very helpful I have rebuilt four of these motors in our fleet and I did it just like you have shown but I still get a lot of what sounds like gear train clatter the motors have been running fine for about a year just thought you may have a idea as to why it's so much noise.

Bien explicado pueden hacer un video así con una válvula R14 mostrando su Reparacion

Do you have a video on how to change the sensor?

Hola que tal es un Actros Mercedes benz se frena el eje de atrás es un doble puente se cambió un pulmón y el otro no yo pizo el pedal y se livera

Where are you located

You figure it out change fuel pump head , lift pump still having the same issue

Súper clean work area, nice video

You got part numbers or parts lists? That's way cool you did that especially the wiring and for it to work with the ac that's where I'm really intrigued.