This was actually very straight forward and easy to do! I did this after installing the fader, but this was the only electronics work I’ve ever done. Thanks for the video! I have the newer preamp, so the linked video helped a lot. Thanks!
Hey Jesse! Followed this video and everything worked perfectly. This was my first time doing any sort of electronics work, but this was actually pretty easy. Thanks!
I order a Tonearm for the STX. The quality is for real total bad. Distorted sound, the headshell can turn around 360° and is loose. And the carbon have total sharp edges. Years ago i buy a PT01 Tonearm in top quality... Also i order vinyls from JD. Not flat and you can see pickels or what ever on the vinyls. Absolut B Stock for the full price.
Having the same problem a few other folks are having im following this video to a T but I can’t get the fader to adjust properly even when the faders supposed to be completely off I can hear the track faintly going. I feel the cut does not even work please help just purchased and new to hobby. Also purchased your tone arm thanks
Ok one question when you put the case back on where are u putting the battery cable? The case is blocking the camera so I couldn’t see. Is the cable plugged in Back where it orginally was? Or is there a new spot on the pre amp or break outboard broad? Thinking about ordering the tone arm n just want to be sure I understand before I buy thanks!!! 14:22 is the exact spot
Especially after seeing problems with installation and such, I'm very reluctant to potentially screw up my portable. Especially since this wa sthe most expensive portable I bought and don't want to break it. Think I'll just put some weight to the old arm with some gorilla tape and the metal from a screwdriver with the handle cut off with a sawzall. The weight alone shpuld help with skipping without me jackin up the main board or bricking the whole thing. Thanks tho. Ya'll should provide a service for the install for us gun shy folk. Stay groovy!
Just bought a second hand modded Reloop Spin & the Jesse Dean tone arm doesn’t drop properly it sticks in position as if the actual arm is too tight in the arm housing. I’ve sprayed contact spray on the pivot pin but not really made any difference. There is an Ortofon OM fitted so do I need a heavier cartridge as well ? Any suggestions appreciated Thanks 🙏🏻
is there a list of all cartridges that are compatible with this tone arm? really want to upgrade my stx but i want to make sure i weigh out all my options. thanks for any info
Is there a trick to make this work? When I run this procedure exactly, I still can’t tighten up the cut in on my fader in the right hand position? Does this only work if I’ve moved the fader to the left?
Dealing with the same exact problem it’s like I no matter what I can’t get it to work. The cut line is in the middle and I still her faint audio even when the fade is completely turned off
Unfortunately very poor quality! The gold plating on a cinch pin came off after a year! I have used the TECHNICS only at home and never puts the cinch cable out.
Sorry. THIS IS STUPID. Turntable DJ's migrate to RANE ONE because we NO LONGER want Needle Jump, Pay for EXPENSIVE Ortofons, etc. Now you're going to put a tone arm back on a non-tone-arm Controller? That's like putting a gas tank on a Tesla!!!
They worked great with my 2 channel pioneer mixer, today i purchased the pioneer xz unit and tried linking my technics into the 2 spare channels on that, absolute no go, thank god i didnt snip off my earth cables as im going to need to feed them back through and use them on the earthing point on the console. Just tuck them in, dont snip them off, you may live to regret it.
Yo Jesse I just got a Stanton and after playing with it for a couple hours the platter squeeks when I turn it. Can you help me? Do I need to get another one or they all eventually make a sound after use.
Can any one help be for a mess up my secod target light...... i never snipped the resister!! when plugged back in my led blew straight away :( my negative wire i soldered onto the bottom pin my positive wire soldered onto the orange lead all that said i never snipped the resister!! so when i plugged backin the led blew.... if i cut the resister in thesecond one and follow the same steps in the video will this solve my problem?? THANKS IN ADVANCE FOR ANY ADVICE OR TIPS
Does the vinyl audio from the STX filter out the lower frequencies? I wanted to sample 7” & 45s with my STX but noticed that the low end is missing from the line out, headphones, and the external speaker as compared to my other standard turntables or the Bluetooth connection using the same songs.
Hello master, I have a pt01 scratch it doesn't turn on. It could be the jack input that is loose from the Board, for that reason it does not turn on. I'll try soldering it loose... Greetings from Chile
Hello master, I have a pt01 scratch it doesn't turn on. It could be the jack input that is loose from the Board, for that reason it does not turn on. I'll try soldering it loose... Greetings from Chile
Yo, I respect and appreciate the mods you guys create, but I have gone through 3, yes 3 numark Pt-01(thank god for guitar centers coverage) trying to install this tone arm. And each time it is always a power issue. I have done everything step by step perfect on this. No breaking, no wires touching etc etc. and this still kills my numarks. Like what the fuck. There should be an updated video on this.
Apologies for my lack of knowledge, but would this tone arm be suitable for an Ortofon 2M Red cartridge or a similar one? Appreciate your guidance. Thanks!
