8:11 never put your fingers around the chain, if the spring decides to jump out it's going to chop off your fingers as the chain is smashed into the post.
Hi do you know if this kuga model has the rear vents behind that bumper? Only reason i ask is i have water leaking into my boot and i hear the vents have tape over them that falls over over the years causing water to get in behind the vents. I know the mk2 has this problem and the Focus mk3 just wondering if this mk1 has the vents before i take it off thanks for your time 👊🏻.
Hallo. I have a problem. Since unboxing this thing my sawblade jumps out of the rolls. Did you ever had a problem like this? I changed the bandsaw blades against better once but no changes
@perssonsgarage Thanks my friend. I tried everything. No changes. It runs for 10 or 15 seconds and jumps out. This thing was new. I have no clue. I tried everything in 2 hours. Even flip the side of the rubber band on the rolls.
Good questions! If you use a gas flame, you sweep over a large area quickly. Same with chemicals, your own work is done fast and you see the result after a few days! With Parkside electric Weed burner, each blade of grass/weed takes a long time to burn and a larger area, takes days. This was the reason for my dissatisfaction with this mashine. It does the job, but it takes more of my own time to cover a similar area.
Hot and Cold water has two small ball valves on the pipes before the Fauset. Hot water pipe is always closed with the ball valve. Fauset is connected only to the Cold water pipe, that is always open.
I just run it until it gets warm in the building, usually 20-30 minutes. But theoretically, one tank should last for about 17 hours if it runs continuously.
I had the same problem with this Vevor Chinese shit absolute junk and a waste of money. I purchased Lancaster made in USA 🇺🇸 and it works great don’t waste your money buying cheap Chinese shit.
It worked but we recently replaced it with a regular faucet and a water heater instead. Mostly because it was slow (You need to have a low flow to get hot water, high flow gives colder water). So it takes time to fill a sink.
Vielen Dank für das Video. Ich würde gerne zwei unterschiedliche Zieltemperaturen zu verschiedenen Zeiten haben. Habt Ihr eine Idee, wie man das lösen könnte? Also von 8-16 Uhr 15 Grad und von 15-8 Uhr nur 5 Grad. Wie kann man das umsetzen? Vielen Dank
Eventuell mit zwei externen Thermostaten, die Sie manuell mit einem Drei-Wege-Schalter schalten. Aber keine gute Antwort, wie man es auf einfache Weise automatisch erhält? Entschuldigung für die Google-Übersetzung.
I picked one up the other day in my local LIDL in dUBLIN. iT COST ME 99 eUROS BRO. gREAT DEAL FOR ME BCOS i NEEDED ONE AS i NEED TO CUT A LOT OF METAL FOR A TABLE SAW BUILD i'M BEGINNING NEXT WEEK..
I had a hitch installed (not by you guys) and now I get water in the spare wheel well. Carpet is only wet in the very bottom of the well, not the sides nor anywhere above that point. Is the rubber grommet behind the tail lights the only place where the installer could have screwed up to let water get in?
Ciao, perchè sconsigli l'acquisto? sul primo test dici che il danno è migliorato molto, sul secondo test il risultato sembra buono, non si vede più il danno sulla carrozzeria. Ovvio che è difficile da usare e che occorre tanta pazienza, ma il risultato è quello che conta: fa il suo lavoro? riesce a togliere piccole ammaccature ? grazie per l'attenzione.
È difficile da usare e richiede molta pazienza, quindi è più economico e più facile incollare gli elementi di fissaggio ed eliminare piccoli danni tramite il kit di strumenti per riparazione ammaccature auto.
So why is it called a shrinker stretcher if it is just a block of bits. Reminds me of the Chinese wheels I bought. After many modifications it's now almost a English wheel. 😂
Väldigt bra hjälpmedel i många fall. Tyvärr är ju verkligheten sådan att man ofta inte kommer åt på en bil med en sån här. Det är trångt, smalt och massa saker i vägen så en sån här helt enkelt inte kommer till att göra sitt jobb. Sen är det ju också så att det som ofta sitter fast är ingängade bultar/skruvar där det bara sticker ut ett bulthuvud och då finns det inte så mycket att värma på mer än själva bulthuvudet. Men det räcker kanske, värmen sprider sig kanske tillräckligt. Har den något namn och beteckning? Länken är inte aktuell längre.
Just bought mine today, prety good saw, the original blade is cheap and dust collection is'nt good, but it does what it need to do. Will be a good addition to my workshop, already have a planer from sheppach. Thank you for the video.