If I have an Insta360 One RS on a chin mount, and an X3 recording on a stick from the rear, how can I use verbal commands to start/stop them both? Does this require one wired lav mic (to the RS), and one bluetooth lav mic (to the X3) tucked inside my helmet? Is there a more simple way? Thx
hello... can we use lightning to multiple usb A connector and connect multiple usb 4g dongles..? and strengthen the uploading speed through network bonding in Moblin. will thiz works...?
It looks like you didn't watch the entire video, because I did cover that. I've managed to get 2 USB-A modems to work with specific Lightning adapters, as long as the two modems were not of the same brand. That seems to be the max.
@@Ragesh-ho1eq Ah. Now I understand, what you want to know. Moblin uses a special protocol called SRTLA, which was developed for Belabox. It requires a SRTLA relay (either hosted by yourself or by subscribing to Belabox Cloud at $10/month) to achieve bonding. Moblin can with that access all network interfaces, that your iPhone has, at the same time. That is the internal data, wifi and modems via USB. So far our testing shows, up to 2 modems can be attached to Lightning based iPhones and iPads. On USB-C iPhones and iPads you can attach even more using a USB hub.
Thanks for the video … I want to set up a very simple video with TimeSync on my iPhone 15 Pro Max that I can then hand over to someone else to video me (… it needs to be simple or I would be asking about the BlackMagic software). Can I get TimeSync into the Apple iOS video recording software? Thank you
Hey my home connection is a bit slower (11MBPS upload speed) than my IRL streaming phone, which is using Verizon. I have both of them set to 6,000 KBPS for iRL streaming (I'm self hosting on my PC). However, sometimes I get a freezing stream. Do I need to raise the KBPS on my PC or on my phone?
Belabox Cloud. There are two components to Belabox: Belabox - the encoder and Belabox Cloud - the bonding relay. Moblin uses the same protocol as Belabox, so you can use Belabox Cloud to achieve bonding with Moblin.
@@Dili832 The EOS R6 Mk II will only output 1080p30 (or 1080p25 depending on where you are). If that's all you need, then there is no difference. If you want higher fps rates or bigger resolution, then you still need a capture card.
@@EmeraldAudiovisual thank you for the reply!! I guess there’s no point getting a capture card if you’re using his camera as a webcam right? Would probably overheat at higher quality
(minute 4:30 on this video)..!! I've just seen another video, where they showed the proper way to pair the DJI mic 2 with the Pocket 3. The DJI External Mic has 2 different way to pair. To pair with the reciever, you need to use the green ligth mode, & for the Pocket, you need to switch to the Blue ligth mode. In order to switch from one & other, you need to star the pair process, pushing the pair button, after that, press the record button for 3 second to change from green to blue. Then the pairing process with pocket 3 will start. While you maintan this mode on the dji mic 2, every time you turn on the mic & the pocket, they will be paired. This is great.!! But as soon as you need to pair again with the DJI mic reciever, you need to go back to the green ligth mode, & you need to do the same proces. Push the pair button, & then the record button to switch from blue to green, & then you will pair the reciever with the mic again. Hope this info helps you & your suscribers. God Bless you all..!!
Hi, thanks for explaining and showing,I have a jetson nano 4g from seed which has no sd slot, it has an old version of belabox from 2022, i have done the flashing onto a usb stick but when I connect the jetson to HDMI it shows a login so cant go any further to install. Is there another way to install the new update?.
I'm looking for help that cannon couldn't give me. I want to go in bulb mode and lock shutter open untill IM READY TO CLOSE witch I can physically do on the camera but I don't want to touch the camera. Do you know of a remote that will allow me to start shutter with a press then end shutter with another press. This is for light painting photography on canon r6 mark ii...... thanks so much for your help
New Insta360 ONR RS Twin Edition owner. Beginning to learn my camera. Just finished my first Insta360 Studio and Filmora video production. I used my AirPods for recording tracks post production. However, I noticed the voice tracks were in mono ( not stereo ) and poor quality. I mostly shoot on and my motorcycle. Is something like the InstaMic simplest solution to record without all the wires, shoes, clutter? Does it record in stereo? Can I also use the InstaMic for recording audio ( my voice ) tracks while using video editor or should I get a wired cavalier mic for that? Thank you for your videos. Very helpful.
If you only care about a BRB scene and none of loopy's other features, you can skip loopy and just put the sources from your BRB scene underneath your stream source in OBS. When the stream source loses connection, it stops blocking whatever you put behind it. Of course you would still want a separate BRB scene to swap to manually, and this doesn't work if you want audio or music to play during BRB.
The issue with that is, that it only can be static content. You won't be able to play clips or the likes, because their audio would constantly be playing while you're streaming. You are correct though, that that is one of the simpler ways of doing things, if your BRB screen just is static content and no audio.
I use the GoPro Labs firmware update and it is really good for what I do. There are many added features that put it above the standard model. In particular, I like is the built-in timecode sync which allows me to use multiple cameras in my videos. The QRControl App saves a lot of time to set multiple cameras’ settings
I did not understand how u connected the osmo action to the rtmp server ...did you need to bring the stream over the mimo app into moblin? Or did the cam just connect somehow?
I'm not sure, what you mean. The LinkPi provides the HDMI from the Pocket 3 out to the Atem Mini, if needed. The whole point of the video is, how you can connect a DJI Osmo Pocket 3 to either an Atem Mini or a LiveU Solo.
It's using the onboard SIM ... and the WiFi ... and then up to 2 more modems. And no, a single SIM is rarely enough to keep a stable stream, if you're on the move. Sure, if you are static in one place, you know fairly quickly, if it's going to work or not. But the idea of multiple data connections is, so that you can have SIMs from more than one provider and your stream doesn't go offline, if one of the SIMs ends up with a bad connection.
The bonding ability seems very attractive. I'm so happy there's an adapter recognized by iPhone that can host some SIM cards and route data through that adapter. 👍
On the current iPhones and iPads with USB-C it's much easier now. It took some looking to find a good adapter for Lightning, that would accept 2 modems, but yes .. it's possible.
Does anybody know which go pros have internal free run time code? also do any of them have the ability to reset time to day, hour, and second? I don’t necessarily need time code all the way down to the frame although SMTPE would be nice and shouldn’t add much of a cost to a camera since it’s a universal format that’s been around for way over 30 years.
All GoPros, where a Labs firmware exist can be timecode jammed via QR code. Only the Hero 11 and 12 can be timecode jammed via the audio interface (LTC / SMTPE)
The hero 9-12 can be jamsync'd to SMPTE LTC via audio jack in the Media Mod. I use the timecode for syncing and playback multiple GoPro Videos with a 3rd party software called Multi-View HD Pro2.
@@EmeraldAudiovisual I was adding clarification to your comment "Hero 11 and 12 only". that Hero 9-12 now accept LTC. The video says 9, 10, 11. Just wanted to clarify for those who read the comments
the new osmo pocket 3 firmware stops it showing via osbot to an ndi encoder and you just get a black screen now, even though it will show on tv. I think its to do with the new res options that can be set by what you plug the pocket 3 into, which the osbot doesn't do
That is correct. And the same happens on the RGBLink Tao, which is very similar to the OBSbot one. It's because they support 4k input and try make it work, but fail. The LinkPi ENC1 V2 and ENC1 V3 still work perfectly with the DJI Osmo Action 3 after the firmware changes. I've got all of that tested.
@@EmeraldAudiovisual Thank you for the quick response, I found even setting it to the various resolutions still doesn't let it through. I'll check over the weekend if putting it looped through a field monitor does the trick.. although it's an extra hop it may get it working
Great vid. ut searching for an option with less wires and lesss a lot of everything. just want the dummy battery small chord plugged into a stationary power attached to the camera.
How do you disable internal mic when using external adapter like you use with rhode mic? i don't see how i can disable internal mic on my insta360 one rs.. please :)
I bought the OBSBOT 2 for My pocket 3 and it doesn't recognize it. Sees other cameras but not pocket 3. I see there is ENC1 V3 on the market, does it convert UVC from pocket 3 to HDMI too?
@@ITSolutionsNetwork That absolutely works. I had the ENC1-V2 on my desk for 6 months feeding a Logitech Brio into my Atem Mini Extreme. It never caved in.
@@EmeraldAudiovisual The thing is, OBSBot works with other USB cameras, but not with Pocket 3. And Pocket 3 works as a webcam on my Mac. It didn't have any settings and I wanted something simple. It should work, I've seen videos where it works, but doesn't work for me, maybe it's latest DJI firmware that they released recently. Have you tried updating and see if it works?
Спасибо тебе, дорогой друг! Ты единственный, кто дал правильный, быстрый и чёткий совет! Я замучился искать ответ, почему не подключается пульт к камере, а ты так легко это показал! Огромное спасибо! 👍👍👍
If I use this setup and want an external mic how could i do that since the DJI camera usb is being used to connect to linkpi? Do I connect audio into the linkpi via 3.5mm jack? I am also only using the linkpi for UVC conversion purposes because I have a live U solo pro and am using that for LRT purposes.
I can confirm, that if you go to "Encode", "Audio config" and set the "source" to "Line", then the LinkPi will take the audio from the 3.5mm of the jack only. This is a stereo input, so if you connect something like a DJI Mic, you will get both microphones in each their channel (or mixed, depending on setup)
@@EmeraldAudiovisual I have the rode wireless pro and am planning to use it for live streaming purposes along with the Unlimited IRL streaming backpack the GunRunV7. I have had a DJI action 4 for a while and didn’t know I could stream with it until seeing this video. Will the audio be laggy using the link pi audio port? Also one last question if I get the DJI audio adapter would that be a better way of using an external mic? Since I could connect the mic via the 3.5mm on the adapter then the usb c that comes on the adapter connects to the linkpi? Thank you for any help!
@@UncleLos i'm not sure, what you're trying to do there. Both the Røde Wireless Pro and the DJI Wireless Mic need to be connected via 3.5mm to the Link-Pi audio in. Yes, they both also have audio on the USB interface, but that doesn't work with the Link-Pi. As for delay/lag, it shouldn't really be noticable.
Absolutely: RTMP or SRT. It's just not capable of bonding and doesn't have adaptive bitrate, which is why it's handier to push the HDMI feed to an encoder, that can.
@@zepplinrossow7618 You don't need this, if you're using Belabox. You can plug the DJI Osmo Action 4 and Osmo Pocket 3 straight into Belabox via USB. The solution in the video is more for LiveU users, that can't connect USB UVC devices.
@@EmeraldAudiovisual Running on a Rock 5a, my intended use was for 1 uvc and 1 hdmi cam in PIP, would this be the best budget option? Trying to aviod buying a Magwell or yolobox
@zepplinrossow7618 ah yes, for that it would work alright. Oh and the difference between v2 and v3 is, that v3 can capture 4k on HDMI and has 2 USB ports.
