We just gott a set and they don't fit with roof and not near the quality I was expecting. Will have toordera different brand. Too many gaps and don't waste your time with the sticky velcro.
@@randyhayes1001 Long term review I completely agree. They are better than nothing but if you don’t get them for very cheap it may not be worth it. Luckily I only need the once or twice a year so they are acceptable for me.
@@littlestews no, at the time I didn’t know it was better to install with one. I wired it to the battery but have added a relay since that install was done.
Just laughing at your bitchn 😂 i did the full access plate yesterday and going over my list i realized i forgot to do the front straps. So thank-you for saving me atleast a few cuss words as i undo yesterday's work.
For the seats - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-y4zzBaJNYGY.htmlsi=7XxuPlV7cgvoOS7e. I freaking love the fans! They are the best add on I did have for SxS!
2023 KRX4 rear axle boot _ Have the same boot spreader tool and Brute Performance Boot Kit. I warmed the rubber boot with heat gun because it was stiff. Split down the seam just like yours. A larger boot that came with the spreader tool was softer rubber and went right on. 2023 Rear axles are larger, I think the Brute Perf. boots may have been for pre 2023 axles. Thanks for sharing
@@IamChucky_ filter oil settled to the bottom, dust got by the filter getting to the number 2 cylinder. Started smoking and burning oil. Luckily I had the Kawasaki warranty and they rebuilt the motor. This happened on my friends as well but he did not have the warranty. Very expensive… we both went to another filter with a particulate filter before it.
@@KRXBrandon thanks for the heads up. I’ll keep and eye out for any dust and tighten the clamp extra hard. Reason I switched to Uni is because the stock filter was letting in lots of dust. I ride in the desert so I definitely need to invest in a particle filter.
Do you have a link to buy those brackets you didn't end up using for the aluminum extrusion bar? The ones that was connect to the round tube on the roll cage?
I thought so as well at first but the movement was so different, very directional. I have not seen anything similar from examples of swamp gas. Either way, it’s super cool to see in person!
Exactly. I've eyewitnessed them too. And they move as if it is someone walking with a light. However after seeing the terrain in the daytime there is no way a person could move the same way. And no I don't believe in ghosts but these mirrored humans but couldn't have been
It could be that they are not worn in yet. New pads can squeal until they are set in. Otherwise could be sand/dirt on the pad or rotor. If it is annoying enough, I would pull the pads, clean them and the rotors. If the pads are metallic they could just be low end pads and need to be replaced. That being said, I have used lowest priced I could find and not get noise.
Hell of a video brother!!! The helpful things to watch out for was perfect!!! preciate the time taken to do this!!! Quick question though, Did the motor just stop working period? Mine were working perfectly and just quit. im gonna buy the new motor but when I open the cowl, im gonna TAP TAP TAP on it just to see if it just had a lil blockage LOL.
I take comfort in knowing when my machine is telling me go get gas I have plenty to do it . Idk I bought mine in 2020 and never had an issue but I am going to do the filter
I must say I've enjoyed your video brother. Very natural. I'm looking to build one of these for my Yamaha but also over consider ordering from the same guy.
Did you keep your springs at recommended preload and crossover measurements from rcore? I’m installing a set this week. Most things I’ve read is there recommended settings are to high for most. Thanks!
I have a separate video on installing it and my Rugged Radio on it - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-tqI_dgNYt3c.html. I got it off of Amazon, www.amazon.com/dp/B097LR21J9?psc=1&ref=ppx_yo2ov_dt_b_product_details&redirectFromSmile=1. I have a more detailed parts list in the info portion of that video. It is a great way to mount things up above and keeping this in range/view but out of the way.
I got mine from Tyndall - www.tyndallsfabshop.com/custom-fan-accessory-units. They have a good Facebook page with lots of information. Mine was $400 but it has been a while, not sure if they have gone up or down since then and it varies depending on the options you pick. Still using them and still very recommend!
At the beginning of your video when you were about to disassemble the motor, the arm attaching to the motor was at the 3:00 o'clock position (05:32). You shouldn't need to mark anything, just put it back as it was when you made the video.
