did your gate come with those brackets or did you purchase separately? I see them advertised as "no drill mounting bracket" but it looks as though the bottom hole needs to be drilled, correct?
I've found it doesn't log all motion when set to motion even at the highest setting. With this thing it's like a crappy car, your under it more than your in it.
I have 03 Mazda b3000 same as 3.0 Ranger automatic 8.8 rear diff. The process is the same, went and bought a gasket set. Replaced head gasket up and I can say the small details are missed, such as craming the bolts into the valve cover with the gasket and new grommets. My suggestion is to use a pick
I don't know how you got that fitting in there At all because it's 1/8-27 NPT and the threads for the sensor are 1/8-28 BSPT. I have to order more fittings. Thanks for showing all that it's very helpful
Followed the instructions and your video. I have a 2023 TrailBoss LT. When folded over into the bed it sits nice. But I find when extended onto the tailgate it is not leveled due to the tailgate does not lay flat. Does yours do that?
I got a bad coil code. I changed the coil, cables, and spark plugs. I saw oil in the well and placed a new valve gasket, and cleaned everything up. It shows a misfire regardless. Ideas?
This looks like the problem I’m having furnace was working on Saturday after two attempts I would only get the fan for about ten seconds then just shuts off. More than likely it’s that switch then.
Mine was too sensitive to how level the trailer is. So if I park little not level, furnace won’t work cause it needs more gravity force to engage. That’s why I bent mine. Makes sense ?
Thanx! This video was helpful for knowing what I needed to buy for the valve cover replacements. I always use a shop manual, but this sums up everything really nice!
Not everyone gets this error after replacing the grille, one person who has installed a TRD type grille on three different Tacomas with the TSS has not run into this issue but he said he made sure the TSS sensor was fully seated on the plastic studs that use the press on lock washers. I hate radar cruise control anyway you end up behind someone not doing the speed limit and sometimes don't even realize it so you travel down the road under the speed limit for several miles before you notice.
I took it all apart and took the night off and loosen the two little bolts on the left side, but the axle didn’t slide out freely, and the other side was like a monstrous indented hex. All I wanted to know was due I find a big monster is Allen wrench for the other side or does it just come right out? However, when I got to the part I wanted to know the video speed it up and it was over for me.
the axle should slide out without needing to use the hex side. just tap it with a mallet. might be just stuck. use wd40, or put weight on the front wheel so its not hanging on the axle and adding weight.
Great video! I have a 2022 Sierra and the instructions are a little confusing. But after looking at your video, it took less than 5 minutes to install.
That’s weird because every video except yours that I’ve seen so far, they say to unplug the battery and to cover the engine bay part and the reason I ask is because where I live there’s like over a dozen vans that do car washes around here, and I even seen them covering certain parts like the engine bay and batteries are m usually taken out from what I seen .
This is the second home in which ru-vid.comUgkx0jZ_lGlDVJhDnmagEU8gn47cmfPNlLQU we've replaced our "regular" doorbell with a Ring video doorbell and we really enjoy it. It is very easy to install and it works very well, with a clear picture through the app and good in-home use (we added the chime, which is also easy to install and doesn't require another thought to use).
Installed it myself without any issues. The wifi signal is great even ru-vid.comUgkxE_D_sddGAdiVUKp7PkkmyxO7bRtgqmk5 when the router is located far away. I really enjoy the night vision feature that allows me to see clearly any activity near our house (mostly cars and wild animals). The motion detection is helpful to me as well to monitor what happens on our front.
UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust ru-vid.comUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.