I figured out how to grind fine for espresso by finding a RU-vid video. Y took off the hopper and the small screw won’t hold anymore. No idea how it was in place before. I wonder if there was an extra piece, like an anchor to make it hold.
We got the 2018 2.0T with a 6speed mt last fall with 35K miles on it, It did need a new radar unit, that the dealer replaced at no extra cost, and we love it. A new radar would cost about $1K to replace so don't bump it or plow snow with it. The negatives are all the same except for the braking error. Haven't seen that one yet. The collision avoidance error is annoying and so far it reboots when you turn off the car and restart it but it's better than it not working when you really need it. It seems to have something to do with the Lane Change Assist system. It doesn't like it when you change lanes without using the directional even when you are all alone on the highway.
I just got mine. UPS was supposed to deliver it from 1:00 pm to 5:00 pm and didn’t. We waited and left by 5 because we had things to do. They left a not saying the would deliver it at 7:00 pm next day. We had to be gone even earlier than 7:00 pm. I had to pay extra for UPS to hold it at one of their locations. So far the grinder is not grinding as fine as I need. Maybe it needs time to adjust. Who knows. My cheap grinder (Crux) grinds finer so far. Wish me luck, or I will wish me luck anyway. $300+☹️
@@MattonEverything6000 I luckily got it in after reaching out to customer service. It was honestly so lucky lol after almost an hour trying. It's like the coffee gods were just toying with me
I think u did a great job. Though I'm worried of over spray and would of used cardboard, drop clothes and a bunch to cover up the door, deck and surrounding areas.
I have a 2020 accord sport 6 speed cv2, that i bought used through Vroom with 6k miles on it in 2022 and i have added the PRL stage 2 intake, deleted the resonator and mufflers and i have had 0 issues with my car and currently have 19k plus miles on it and i have NEVER had any of these issues with my car.
Every issue you named.... I dont have 😂 The leg resting on the center console... Mines padded ? 🤔 A tank of fuel will last me almost 2 weeks 🤔 The TPMS thing for sure is irritating, its always on 😭
You really need to unscrew the end caps off the brush bar and clean them out. If your bar was that dirty, you will be amazed what’s in the end caps. When they get plugged, the bar won’t spin.
My brush was clean and it still won’t spin. I took off the end caps as you suggested and found the hairy problem. Thank you for this comment. Otherwise I would not have known. Thank you Sir. 🙏
$50 replacement on top of the oil change. Bought the filter for $28 using a coupon from the dealership. Saved $22 for 15 minutes work. And I’m sure it’ll take 5 next time. Thanks$$$
This is a pretty decent guide. One important thing you missed was wiping down the surfaces with methylated spirits or cellulose thinners. Getting any grease of smooth metal is really important. Also, lots of people use all in one paint/primers and thats completely fine but if you want it to last, not just look good, you need to build up the thickness of the paint, this decreases the amount of moisture and oxygen that gets through the paint film to the metal in order to start rust. You can also use a primer high in zinc if you want to increase the time untill repaint. A couple of coats of rust inhibiting paint/primer is a good basic spec, if you want a long lasting system then it would be zinc primer, two coats of micaceous iron oxide and one of of metal gloss...that should last 15 years or so. Also wire brushes are probably better on your angle grinder than sand paper.
Brother, position your prompter to where your camera is or just show other footage with voiceover. Currently, it looks like someone made you read an essay at gunpoint.
