This ist cool

This looks like a labor of love. I don’t know how much pedals cost but I’ll probably spend less just replacing them annually than doing all this work.

😂😂😂 new bb is rougher than a badgers arsehole!

There are tubes that are thicker to prevent flats. Yes, they are heavier, but it's worth it. I road with them in BMX for YEARS. Never had a flat tire except when I ran over a nail. After years of dealing with stickers to goat heads being the number one reason why tires went flat. I invested in thorn resistant tubes. Best choice I ever made. A normal tube lasted a week at most, thorn resistant tube, I ran for years.

Que liquido usas

Power tools near a bicycle bro nah

Good quality square taper BBS are no problem at all. It's the many cheap ones which have issues.

After watching all these shorts I feel it's good to buy a single gear bike 😂

After watching all these shorts I think it's good to buy single gear.. bike 😅

Copper slip every fixing when it’s new and this shouldn’t happen.

Pistons are seized , thats why they squel

Gotta go home and grease my fuckin balls

Im Ernst? 🤦

maior trabalho para por um pedal frágil

🤦‍♂️... 1x kurz 5bar drauf und die Flanke setzt sich richtig. Mit Seife kann der Mantel Rutschen.

Bro just use sand paper and isopropyl alcohol. It dries so fast you don’t need a heat gun. Just soak the piece of sandpaper in IPA and and rub the brake pads on it to remove contamination.

You forgot the bit where the Square Taper BB cups are seized in the frame and the Tool snaps off the tabs so then you have to get creative...

2 percent of people do this

Your supposed to use a rim band not tape

Der natürliche Feind des Autofahrers.

This is a shumano hollowtech II , right?

Ooooh maintenance! Saying that I reckon if you don't want to be doing this just buy cheap non serviceable pedals and you won't have to.

Du hast eine leichte 8 drin. Aber das weißt du ja. Wir gehen zum likes und Kommentare.

Bullsh…. Doesnt work !

Seriously 🙄

And he adds it back in! I recently went back to schwalbe tubes with inner sealant had enough of this maintenance of tubeless it gets to u in the end lol

Le tip top!!! 😊

I used to work in the tire and wheel department of Murray bicycles in Lawrenceburg, TN. I was a truer...I turned and loosened spokes to make the wheel straight and true.

Godzina w pracy i masz jakich kilka ;/ chyba lubisz dłubać przy rowerze

Looks like the inside of my pocket pu..... nvm

They still make stationary seat post?

cheap junk should have been put in the bin the day they were delivered lol

The clutch system must be lubricated with a special grease, not the usual green one, because there is very strong friction.

What sort of Grease ?

Muito bom 😂😂😂

What did you do?

Really??? Everybody knows how to fix a flat Tire! This Repair Set is been around for years.

Ahora explica como el hombre llegó a la luna porfavor,😂😂😂

Thank you for teaching us how to clean bicycle brakes? 😁

You are doing way to much extra work

More idiots creating solutions to problems that never exist. I have never had a seat not tighten enough because the seat bar clamp would not hold. Thats kinda why it has that nut on the opposite side so that you can adjust it for perfect tention. I figured that out as a child so if you cant do it you should probably find another hobby

I don’t know if this translates to bikes to but break pad dust is super toxic- 💀

You forgot the magnet for the crank sensor

how is this a "hack", you're replacing your brakes

Where is the nut that nolds the presta stem in place?

This is fucking ridiculous just to grease 1 pedal

So simple, yet so complex! This is great knowledge you have my friend!

Che giocattoli

Easier, more effective and cheaper to replace the pads.

The clutch is just there to Reinforce the cage and secure the chain ... there is no impact on shifting gears ! I cant see the point of this vid