Hi, I can se you did not put sealant on the oil pump, which is between the two compartments. Is it okay like that? I am just rebuilding mine and unfortunately I noticed that I did not put enough, thus I can see trough.
Hey thanks. I found this same fridge at a thrift store for a couple bucks. The 12v side works fine but the 110v does the same as yours.... I was actually looking for diy stuff and this popped up.
My daughter has same fridge and fan started making strange noise when cooling is activated and barely spinning. I’m planing to replace the fan and existing label only specifies 12DC Brushless Fan. When I search on amazon for fan, some of them specify ampers. Any idea ?
Will this Ecutek ECM software tune work on Stock GTR 2014 DBA trans with FBO ?? I just switched to EcuTek from Cobb--DONT wanna damage any forks, clutches on OEM gearbox etc -->WILL this TCM tune or similar work from your Video with different touchpoints--pressure etc?? My EcuTek Tuner Sam Barros says he can do the TCM revision tune ONLY-- IF ALL SAFE-on Stock OEM Trans or does it require Jacks clutches, seals upgrade-rebuild? THX
I have this exact same machine but I think you're expecting too much out of a portable battery powered unit because I just used mine for the first time today airing up all 4 tires from my friend's trailer with one of them being pretty low and it did take a little while but it didn't take that long and I think it goes past the amount you set it at because when you take the thing off some air always comes out like maybe 1 pound or so but I've only used mine once but I think it's pretty awesome so far honestly.
Jack, I recently did a transmission oil change. Took my GTR to the local nissan delership to do a relearn but they told me there is no TCM communication. Any idea why this could be happening?
Hi, thank you for posting this! I have this same mini and it doesn't get cold at all. Instead it was hot. Bought it on fb market the other day plugged it in and put cold setting on. Green light on back works and three mode lighting on front mirror works... Just wondering what would you recommend to solve this issue? Any advice or suggestions are appreciated. Thank you!
At 27:10 he just straight unscrewed that filter housing without pulling out the plastic locking arm up top. I don’t know anything about these trans other than that. That’s all I know. I also know the filter housing assembly that the lock arm is attached too is about 300$ if you break that locking arm off. lol other than that I’m loving this video. Thanks for sharing. Hope that arm made it. lol
Dude I noticed the SAME THING TODAY !! my twin brother called me and was like , man these are nasty , I said man I JUST noticed the same thing !! We both drink them every morn , we both left the same gas station at the same time this morn ... weird !
I'll give the 1/2" PEX a try the next time those aftermarket plastic bushings crack and fall off. I think if they were Delrin and the correct length, Id and Od they would never need replacement again.
Great video doing research now for a Ls swap in my Baja. Flywheel was hanging me up. Looks like a f body camaro flywheel works aswell. Did you go aftermarket camshaft?
Hi, I confirm that the 10MicroF/50Volts capacitor was the culprit. I got the AstroAI LY1906 Model, with the same problem of the flickering light in the front. Just change the capacitor and way to go. If you can acquire the rest of the capacitors, like the video says, change all... but in my case, just with changing the 10Micro/50 Volts Capacitor do the work. For the tech you out there, i test the bad capacitor and mark 9.75 microF, so i change it. Thanks Jack for the video advice.
Well I just did this to my 91 Ranger now the door is stuck closed. Any tips on where to go from here? Hoping I can get the door card off to mess with it while the door is stuck closed
Hi, I have a mini fridge I’ll like to fix also but it’s very complicated for me since I don’t have money or the supplies it seems the power for turning it burned down so could I ask if you could check it out if I send it to you through mail and you could fix it for me?
Torx T50 is what's needed to remove. Think I am going to make a new video noting the required tools, most vids I have seen jump right to removing the bolt. I'm also going to try and stick a magnet next the post to try and hold the nut in place.
I moved from Ohio to Florida and seems my mini fridge broke along the trip and now has this surging issue with the light. The fan spins fine. I’m compfortable trying to solder (even thought I’ve never done it before) but is it worth money wise to buy a soldering kit for this or is it cheaper to get a new fridge