Is that the original spindle , I’ve the 4030 machine and was thinking of changing the spindle to a more ridged one . Any recommendations.🤔 All in all they are a very sturdy machine for the price .
Voltage drop is based on resistance of wire while moving current (amperage) 12v ( good wire) 12v = 0.00 on dvom 12v (bad wire ) 7 v = 5.00 dvom Using ohms law resistance can be calculated, helpful for sparkplug wires. Bigger the draw the more likely to find problems.
Thank you! Is it the same on a big block Chevy? Air cleaner to drivers side valve cover & passenger side valve cover to carb? I’m trying to fix this issue also.
My 351w stroker is getting too much pressure, got the vent snd the pcv but still needs more. My dipstick is struggling to stay in, burns about a quart per 50 miles, and leaks out the oilpan. Engine has about 2,000 miles on it and im struggling to find a cure.
I have a very similar challenge. Picture Frame from son most of 40 years ago. Just stopped working. I can pull the board out and send it to you. I understand it is not for free. Can and will you help?
How do I change the batteries? I unscrewed the little back "door" and removed it, but I can't get any of those little batteries out. They're all down in those "wells," and I can't get ahold of any of em. If I'm supposed to open the entire frame, like was done here... how do I do that?
I usually slap the unit in my hand and they will come out. If not then you can open the case and push them out. Those batteries swell when they go bad and it's hard to remove them. Good luck and if I can help, let me know.
No, you'd be better adding a little bit of channel delay (not the effect) to help with feedback. Best thing is to ring out the system beforehand and bandaids aren't needed, But I must admit have done it myself in a pinch.
Great video! Maybe you can help me before I buy this machine. Instead of the existing spindle I need to have my device that would just press down onto the surface. I measured with the scales underneath and even 2kg load is enough. Do you maybe know if this machine can put this much downward force, or does it have some safety feature that would prevent it? Thanks for your help!
Rick is amazing!!! He fixed my device and saved the audio file, and it is on the way back to me as I type this. Reasonable price and great customer service, I could not give higher praise to Rick and his business.
CAUTION !!! Preditors use these type games and tactics to LURE people, women, teens, or children, to a secluded location. Or to LURE them to a public place where the preditor can oogle their target. Choose who will become their next target. And/ Or pretend to randomly meet their target. Obtain contact and establish familiarity,learn more about their target, and lay the ground work for more contact in the future. The preditor already knows that the person is gulliable, foolish, and careless... Because the target has naively allowed themselve to LURED into strange territoy by a stranger. The target is easily distracted. Their guard is down. You might find yourself wondering into a thick dark woodland. Or off the commonly traveled/ populated trail. Wondering around with your focus on the ground, and Not On Your Surroundings. BE CAREFUL OUT THERE.
I always privately tell people and my wife to be aware and keep any required protection on themselves at all times. Thanks for the great comment... Many don't realize
The kit which I helped engineer is no longer available I heard (don't work for DDM anymore) but I think we did 7 cars and not a single one was cut or beat in any way. Heard about a company (Wades or something) that offers a bolt in kit as well. Never seen them, the hard part is getting the BCM to like talking to the E67 ECM for the LS3. Probably one of the major reasons the project was dropped.
Yes, it's actually easier than you think. Select Parallel on the type of operation and if you use a drag bit enter 0 for RPM or 1 of the post processor complains. Then go to select your area and it will turn blue. Then tell it how much stepover you want and hit ok. For drag bit simply pre load the bit and for machining you gotta lie to the machine. Set Z at the proper 0.000" and then manually enter 0.001 into the DRO. It will cut 0.001 deeper than true Z and you can sneak up on the cut to get the cusps that you want. Fusion will complain about cusps and stepover being larger than the tool and it's ok because it's a V bit either way and just ignore the warning. Try it