Nice job thxs

How much for a total rebuild engine of 750k miles DD15 ?

What’s your contact information to give a call?

Hello? Am from Kenya kindly assist with maintenance manual.

Definitely not that easy when you have the 3 filter style and limited space. If youve had one with difficult torques bolts to remove then youd know.

Thanks for sharing great video i can really learn something about the SCR system 😊 and deisal

Thank you sir

Very helpful. Thank you

Hi my name for you I have a shop in Brookfield. I have a problem for DD 15 lost a prime and want to talk to you about this more. Maybe give me a little information please thank you.

Wow how amazing video, thank you so much

Please give me your phone number

❤❤❤❤

❤❤❤❤❤❤

❤❤❤❤

Thank you you are so good doing the work. I learned so much with you. Have a good day. God bless you.❤😊😅

what is the part number?

Where you guys located

👍🏼

Show us how to replace the engine harness on dd15

Everything you said in the first 2 minutes happened to me ….loves put me in a regen and walked away. Everything cleared until about an hour later

do this in chassis on a fire truck!!! this vid is so simple..but try to remove it from coiming out bottom!!! good info to know!!

I was able to replace one on my Vanhool tx dd13 did everything you did and prime my coach change the fuel lines o’rings. Now my surging went away and also my rough idle. Thank you

Thanks for the cool videos you make for us ,they are made professionly and are really a money saver for us. I have a 2020 Freightliner Cascadia with a DD15 engine auto trans with 676000 mile 13000 engine hours.I do lot of repairs myself but lately I have noticed that the engine fan is always on from the moment i start my truck in the morning to the end of the day. This truck is equipped with a viscous electric fan with no air suplies to it.I checked all the plugs and sensors they are all in place. I took it to my regular mechanic and my local Freightliner dealer and they couldn't detect the cause or any problems.I Even replaced the fan clutch myself but still the problem accured. There are no codes on my dashboard .but the engine light keep comming on , it gave me on my scanner a message ( SPN 0 /FMI = 0 Data valid but above normal operation al range -most sever level). Should I check or replace the ECM computer? What do you suggest?

Number 6 when its in the truck lol

Cool video ! Around how many miles would this part start failing ?

My DEF quantity is at 400-500 g/h what can be issue? I don't get any CEL about that. I do have SCR nox low efficiency

What are symptoms of bad quality control valve?

What did u use to lube the injector line?

Tks

How long does it take for this rebuild to be done? 1 week?

Question...If, during a regen, the SCR Outlet NOx Sensor is reading say 400ppm and the SCR inlet NOx Sensor was say 300ppm...what could be the cause of that?

Most of this is completely unnecessary. Just take fuel line bolt out. Pull out by hand, drain coolant, remove bracket, remove regulator and go in reverse.

Great video. Thanks for sharing

I had fault code, for nox raw...can't remember the actual spn/fmi. I ran Regen numbers looked good and both nox dew point turned green. However, nox inlet was 1650ppm and outlet 3ppm and nox conversion stayed 0.0255 thru whole test. Co worker threw inlet nox sensor. Would that be remedy to that issue.?

Super well explained thank you!!

Question? I have a truck I put a new one box on for high doc pressure 2.548 and higher. Replaced the one box and pressure is higher than it was before replacing doc and dpf. Updated mcm,cpc etc. Any info on why I'm seeing this

Can you show how to diagnose and replace an air compressor?

Is it normal for truck to puff white smoke when driving...?

Call me anal but I would continually clean as I went with brake clean fluid and I would make a plastic bung that goes in opening before I did any surface cleaning then after cleaning again with brake clean I would remove bung to drag any contamination out with it, my though is to have a bung with a little handle in centre and made to take old oring so when it's removed it wipes the bore clean, see told you I'm anal or OCD whatever

What you removed was the cold pipe. You might not see anything there in the early stages. The proper check is at the hot side.

Thank you for your video. I have freightliner Columbia 2006 , 60 series and lately I am having issue with black smoke and losing power. What to do? I changed my west gate actuator, new delta sensor too. But when I disconnected the delta sensor, there is no black smoke. Once connected there come black smoke. Please , any thoughts?

Great video, tons of info!

Dude you’re the best! What happens when my truck throws a shit load of white exhaust and wants me to do a p regen. I will do a regen. And then I will just take off and haul ass . For about 20 miles it will smoke like crazy then all of a sudden it stop smoking and it’s fine for about 8 hours . Then I have to do it all again. I’m guessing my doser is staying stuck open or isn’t injecting fuel it’s probably dumping fuel

Could bad seals be the reason why i have to prime once i stop running the truck after about 8 hours but once I prime it I have no issue with the truck until I let it sit overnight

Million times thanks. Love you. God bless you.

My truck was giving me 3 .5 milles per gallon ofter 6 hours of driving finly Rich up to 5.6. Can enybody tell me what to look for

Great video. Thank you so much for the information. Quick question after replacing this do we need to calibrate truck or not ? God bless you.

Exelente demonstration

How about doing it while on chase

Can you do this without draining coolant