i just followed most of your directions (pulling back on the end of thing on the end instead of using your thumb nail works WAY better) and my airbrush works SO much better. thanks a lot, man!

That looks really nice.

Do u need a specific needle? Mine is a .30 and men it cloths so much I couldn’t paint it and I use so much thinner

Hmmmmmm............. Why would anybody let their airbrush get that bad in the first place. Makes it that much harder to clean.

Isopropyl alcohol works to at removing the paint from the brush, 71% and 91% work wepl and dont hurt the brush or the model and it cheaper then tamiya paint thinner

You can get a .3 needle and nozzle for the Patriot 105.......

Terrible video, great concept.

Thank you so much for this!!! It still works and they added stuff

Can you link the screw, bits, and tap you use?

Question will this help the fact that my nippers arent springing back all the way during use

Do you topcoat then weather or kust weather straight on to plastic then topcoat?

Great video! Do you use a mask ?

Philips head screws make the car look too cheap. Should have gone with button head screws

Can you use any other tools besides those applicators you have? Also really nice tutorial and plan on getting my hands on the weathering master

HG or MG ?

In What did you soke it in ?

So did you use a top coat after decals and lineing and then do this?

thx for this vid bruv, I was about to add Peddinghaus decals to my model and was wondering if I can use warm water in place of the micro set and sol liquids

my neo is constantly clogging and I've tried a million things, but not this... I just ordered the .5 setup, fingers crossed! Thanks so much for the vid <3

I just picked up a Neo. Great video.

Bro is the chasis trash if you were to drill too down the little pole

Might as well buy the revolution

Question, what if I want to do this with dark colored and metallic plastic? I want to add rust to gunmetal and silver parts

Wait yall dont be buying these?!?!?

We’re do I dint the 256 drill bit

What model you working? 1/144? Or the 1/100?

Bro I got 3 of these for Christmas

Bro, you’re a straight up legend. I wake up and see a vid of you doing a steezy heel flip on a fingerboard, check my mail and my Godhand nippers just arrived so I search a vid on how to maintain them, boom, there you are again. Look up some tutorials on gunpla weathering, boom there you are again. I wouldn’t be surprised if you pop up the next time I search for sim racing tips. ✌🏽🛹🤖

People who have it 👇

I just snapped my nozzle off 😞 hopefully I can exchange it but I’ll probably try this tip out

Nice vid. New to weathering here.... Just a quick question, after weathering, do we need to do anything else like maybe another topcoat or that's the finish line already after weathering?

what is that you are putting onto the sprues, im just getting into this kind of model making and am unformilier with what you are doing

I am doing my 1st model it is corvette c6 the problem is when start to apply decals on my car the decals breaks easily anybody have solution for that ?

The thing that never tell on diorama tutor are how to calculate the building

Do I need to top coat it before painting or weathering?

What material do you use for the walls?

What gundam is this ? I want one lol

man... mine just foam up and clog the airbrush. I have tried three different ones with same result and i shook and used a paint mixer and everything. just fizzy sparkling milk

wish i could have a pen like that lol cause I thought I had those pens

I see you shake the panel liner....IM SUPPOSE TO SHAKE IT?!

Thanks for the tip. Night and Day difference. The paint I use is mostly Proline water based. Recommended to use .5 so I was reducing it, and reducing it and reducing it to get it to spray and not clog. But it still sucked. got the .5 upgrade suggested by you and it's sooooooooo much better. Now I need to get better at spraying since I can't use the clogging as an excuse. 😂 Looking forward to getting good enough to upgrade to a better air brush. Thanks again.

Are you sure that is a neo?it looks more like a hp- cs or a revolution. The paint cup is very large .

Great vid! What size screw are these? The link is broken. Thank you

Actually, you can use the screw to tap the soft metal directly... no tap required.

Tamiya paint has its own thinner depending on the type of paint. Also they cannot be thinned with water or straight acrylic thinner. I use tamiya acrylic thinner at a 20% thinner ratio more or less and have had great results.

how do i removed the stock exhaust (hotwheels exhaust) with my sand paper? i tried it and it works but there are still some marks. how do i get it rid it fully? (sorry for bad english im a malaysian)

A mí me vino fallado xq en la mano q son abiertas me mandaron una abierta y otra en posición de pelea

never remove your air cap with the needle in , it can damage the needle . 0.5 if a large nozzle for air brushing , it would be very difficult to do detail work. you could just thin your paints and use the standard nozzle . clogs are not caused by tip size they are caused by poor quality paints , paints not thinned enough , tip dry and dried paint from the cup getting into the fluid tip primarily. both of those airbrushes are great! and highly recommend them both

Woww that turned out really nice. The miniatures and signs really completed it

What materials did u use for walls , is it pcv ?