Video instructions for repairing electronic devices. The video series "ONKYO AV Receiver" shows how the ONKYO AV Receiver (TX-NR 737) can be repaired easily and inexpensively. In the video series "Electronic Devices" devices for repair are presented. The video series "Electronic Circuits" presents the basic circuits. These videos are of interest to anyone who wants to simplify troubleshooting an repair of the ONKYO AV Receiver. My aim with these video tutorials is to make repairs to electronic devices easier, to extend the service life and to avoid unnecessary electronic waste.
very detailed & useful video Thank you!. I used your info to understand why my reciever shuts down - The reason shows up as VOLTAGE. History: I radomly get static noise out of any channels especially when there is no I/P signal & the volume is above 20. One day the Static noise came too high & it has since gone to Protection mode and shutsdown. The intresting thing is that if i reset the receiver it would come back good for a few days and then the static reappears back(not restricted to any particular channel). I also lost a Tweeter due to this issue. Any idea where could the fault lie at ?
Thanks for this overview and review. my Hanmatek DOS1102 inverts both channels CH1 and CH2 at the same time even though only one channel is selected. Is there perhaps new firmware for the device? I have version V3.1.0
Thanks for this overview and review. my Hanmatek DOS1102 inverts both channels CH1 and CH2 at the same time even though only one channel is selected. Is there perhaps new firmware for the device? I have version V3.1.0
I was looking for a cheap DSO oscilloscope capable of doing a decent XY Mode, because I have seen many that have a crappy XY Mode with a few hertz refresh, really far away from what you see when they display data in normal mode. Unfortunately you have not tested it on the DOS1102.
Hallo, ich habe das Modell aus 2023. Es gibt keine Einstellung für die Helligkeit vom Display. Unter Utility, Display ist keine Einstellung möglich. Kann mir jemand helfen?? Schön ist der neue 5 Volt Anschluss, damit kann man mit einer powerbank auch draußen arbeiten!!
Salut, il y a trois ventilateurs : le ventilateur intégré avec un capteur externe sur le boîtier et deux ventilateurs avec un capteur intégré. les capteurs ne sont donc pas modifiés et restent intacts.
How you get in your troubleshouting that the CAPs are the problem and not other part of HDMI Board? I have the same problem in TX-RZ810 that suddendly no picture on TV.
Did you figure it out? I have a TX-RZ710 that has no video out. The sound still works, and the TV still detects the hdmi cec data, just no video signal. Thanks.
My unit failed after 3 months. can you get it fixed ? . I can fix it my self if I know what component(s) failed. Tx. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yuWwmWN-bYI.html
Wie messe ich mit der Einzeltriggerung ein 1maliges Ereignis ?: Nur Ch1 ist eingeschaltet und man hat zwischen Probe und Masse einen 1kOhm Widerstand, der zu nahezu Massepotenzial führt. Nun schließt man dazu eine 1.5V Batterie von Hand parallel. Ich möchte dieses 1malige Ereignis mit einem Triggerpegel bei 1.2V und der steigenden Flankentriggerung erfassen. Eigentlich ganz einfach, aber mir gelingt es nicht, weil die Triggerkonfiguration immer wieder nach AUTO oder NORMAL aus EINZELN herausspringt und ich das Ereignis nicht aufzeichnen kann. Es muss doch möglich sein dieses Ereignis auch im Bereich von usec aufzuzeichen, wobei man dann das natürliche Prellen bei der Kontaktierung mitmessen können sollte. Haben die Geräte hier einen Fehler oder ist die sehr dürftige Funktionsbeschreibung daran Schuld, es nicht ausführen zu können. Ich stehe davor das Gerät zurückzugeben.
Bravo et merci pour cette vidéo très détaillée 🙂 Je voudrais l'acheter mais avant il faut que je sois sur qu'on peut travailler en mode trigger one-shot et pouvoir agrandir le signal après (horizontalement) pour le voir en détail (comme un flux série par exemple. J'espère que je suis clair...
I want to adapt a new fan in a circuit where it has a faster fan but the same amount of airflow. This circuit has a protection that trips because of the lower speed of the new fan. Can I make a circuit to multiply the pulses sent by the fan's tach?
Instead of opening up the receiver and soldering in the power supply cables, buy fans with USB power supply and plug them into either the USB power on the back of the receiver or an AC to USB transformer plug. Then just place the fans on top of the receiver. That is easiest and cheapest, plus it doesn't void your warranty.
Hi, first, congratulations for the video. It's very detailed and guide me to understand the problem with my TX-NR797 (Main HDMI Output not working). Unfortunately, I didn't find any Service Manual in the net for my model and I can't find the correct capacitor to exchange and see if it fixes. Do you have the manual or someone else from a similar model or any other tip to handle this?
Thank you for this video, it is the only clear and concise one available that I could find, that has shown me how to use the scope. When I bought it I had no Idea how to use one, but thanks to you I now have a basic understanding of it's operations.
Before I do this how do I know it’s definitely it’s the capacitors that need replacing? It is only the main HDMI out that doesn’t work the secondary is fine. When I scan thru the chips the K one gives me the ?????????. The rest are okay. Thank you kindly for any advice!
Hi. Ich hoffe, dass du noch aktiv bist :) Ich habe ein Problem mit meinem Onkyo AV-Receiver TX-NR636. Das Problem ist, dass ich mit meiner ps4 pro und ps5 erst Bild/Ton über hdmi bekomme, sobald ich den Quellenanschluss teste. Vorher bekomme ich gar kein Bild/Ton oder komische Bildfehler. Danach kann ich ca. 2,5 Stunden spielen und dann kommt es zu Bildfehlern und das Signal verschwindet komplett, bis ich wieder den Quellenanschluss teste. Dann kann ich wieder 15 Minuten spielen und danach verschwindet das Signal wieder. Bin mit meinem Latein am Ende und hoffe du kannst mir helfen. Lg
Hallo, wenn der Fehler im laufenden Betrieb auftreten würde, hätte ich auf ein Überhitzungsproblem getippt. Das hättest du einfach testen können, in dem du den Receiver ohne Gehäuse betreibst. Wenn der Fehler ohne Gehäuse nicht mehr auftritt, dann ist der Grund die Abwärme, die nicht abgeleitet werden kann. Du könntest das Problem dann mit einem Lüfter beheben … In deinem Fall gehe ich von einem (bereits) beschädigten Bauelement z.B. IC aus. versuche mal den Fehler auszulesen. Ich habe hierzu ein eigenes Video erstellt. Unmittelbar nach dem Start. Dann wenn das Gerät funktioniert und dann sobald die Fehler auftreten. Und dann Vergleichst du die Ergebnisse. Mit etwas Glück erhältst du Hinweis auf den defekten IC, der betroffen ist.
@@alexanderh1980 Bist du der Betreiber dieses Kanals ? Wenn nicht, weiß ich nicht welches Video du meinst. Auf deinem Kanal sehe ich kein Video. Ich denke Überhitzung kann ich ausschließen, da der Fehler gleich von Anfang an besteht.
Voltage deviation can easily be calibrated. If you open housing and look from the back onto the front panel, the very left blue Potentiometer can be used to make the display Match aktualisiert voltage.
Hi there, thank you so much for this video. I have a Onkyo TX-NR609 that is broken with this exact problem. It is in quite a remote location in another country. If I would to order the same capacitors would it work, or would I have to hunt down the wiring diagram to check ? I can solder, but from an electronics standpoint, that's about my limit. Many Thanks Ian.
I know this is 2 years old, but I'm curious. Do you need the resistor to control fan speed or ca you just adjust the power cutting the yellow wire? I'm thinking of using a septic dc to dc buck boost converter to control speed of 5 fans. Any thoughts?
Merci pour cette vidéo, car celle-ci m'a énormément aidé pour la prise en main de mon DOS1102. La documentation fournie avec l'oscilloscope n'est pas adaptée pour se familiariser avec les différentes fonctions. Sur ta vidéo, je constate que ta version est V4.0.1 alors que celui que je viens de recevoir est la version 1.3.0. As-tu effectué une mise à jour ?
Salut, content que la vidéo t'ait aidé. C'est vrai, la documentation ne contient que des connaissances de base. La vidéo date de 2020 et je ne l'ai pas mise à jour.
Hi, Hello, I’m writing yours in Turkey. We have a ONKYO but somedays ago we met new problem about HDM card. I asked all province ONKYO service and then I couldn’t find it. I am wondering about if you have a hdm card, I’ll buy it. I’m waiting your answer.
I would recommend the modification in the following cases: 1st the receiver generates a lot of heat and 2nd there are known technical problems (malfunctions) caused by the high temperatures in the inside of the device. You can find these technical problems e.g. in internet discussion forums.
@@alexanderh1980 Thanks, I don't currently have any problems, but I've seen several RU-vid videos with pan modifications that help a lot, any forum addresses? Thanks in advance
@@alexanderh1980 Thank you, I'm Italian and I use the translator, I watched the whole video using Italian subtitles, maybe I missed that's why I asked you about the plastic container
Hallo ich habe für meinen av tx-nr809 die Service Anleitung aber die Lautstärke Daten sind da nicht drauf. Habe mit großer Mühe ein neues hdmi board bekommen habe aber trotzdem Tonprobleme
Hallo super beschrieben hätte mir deine videos in deutsch gewünscht ! Wie kann ich dir meinen Fehler an meinem Onky zukommen lassen ich denke du weisst was mir da einen Streich spielt ......