A few friends hanging out and working on some project cars to sell or our own cars. Some videos will be how too's and some will be just us working on stuff.
Uuuuhm that is not the original filter.. original filter is a black box which houses a filter compartment inside. It sucks the air through that hole in the frame on the carburator / clutch side of the moped.
Where did you get the coil? I just started looking into fixing my grandpa's FTB20 propane lift and cannot find any info lol glad I found your video!! No Brakes or Rollover cage the pucker factor @ 10 rolling off the trailer!!
Righteous! I think mine is 12v.. the dead battery was a Group 22f (12V) MAN I am excited the last time I drove this was almost 30 years ago when I was 5 and got it stuck in the mud lmao@@grandmasgarage3183
Hello from Canton OH!! I have a 2002 I need to do this on but am hesitant to do it by myself without a lift. Would it be possible or do I need to put it in a shop?
You could do it on the ground it’s just not going to be as easy I have removed subframes on jack stands to pull transmissions before it was easier you video on a lift
Hey, thanks so much, I just bought a 2002 Honda Accord with both door lock switches missing (well, the covers are missing). I bought two switches on eBay because, wouldn't you know, my local pick n' pull, somebody had already taken all of these off every single 6th Gen Accord 🤣🤣🤣🤣. Still, though, I'll replace it myself as well as new handles since the ones on mine are all dinged and cracked. This video was a twofer, I get to see how to do both! Appreciate you, sir.
NEED TO KNOW. THERE ARE 2 VACUUM COMPONENTS ON THE CARB. THEY ARE NOT WORKING. IF YOU REBUILT AND PUT THOSE BACK ON. THIS COULD ABSOLUTELY BE YOUR ISSUE. RUNS GOOD THEN IT DONT RUN ABOUT 50 MPH AND SPUTTER I AM FIXING TO START MY 85 BEAST I WILL POST AND I AM SURE I W ILL THAT THIS FIXED SAME ISSUE
Could you please measure the bottom to the bottom of the strut. I’m looking into getting some from Facebook but the guy doesn’t know if it’s for a 5 inch lift or a 7 inch lift
Not the best video tbh. Not showing what they're doing close up, not mentioning bolt sizes. Makes the video not useful. But cool for s vlog or something I guess
It’s probably same order and bolts in very similar but not exact. The only thing I would check for is upper motor and trans mounts so it can hang when you pull off the subframe.
Here I am done changed upper control arms tierods lower control arms ball joints trying to find the source hoping the rusted dub Frame wasn't it but I will say some of it still need to be changed anyway the old honda been thur alot think I'll sell it lol I can agree here in ohio is rough when comes to rust
I know the feeling cause now the subframe is fixed I could probably keep it for even longer but now I need brakes and the trans I think is starting to slip when do you just give up on it
I feel like that's what I have to do with my car, I need to look it over but I hear a popping noise around the passenger's floor board. On a scale from 1-10 how smooth did this job go.? Thinking about tackling this project by myself.
Could you possibly go over the video and add verbal descriptions of what you're doing at each point--like what part you're taking off, what mm socket you're using and so on. It would help the viewer a lot.
It’s not the worse one I have done but it is a front wheel drive car so they kinda suck. It’s not to bad one for a newbie and I had to do my first one too.
Honda is well aware of this defective subframe issue. AC drain drips right onto the subframe on the right side causing it to rust out. This is a common problem from 1998-2002. In 2003 Honda changed the AC drain location and no more subframe rusting on the right side!
@@grandmasgarage3183 thanks brother my wife said the same thing got to lookin and I have the same problem u have I'm in Hamilton ohio how long it take u to complete the job?
Good job. I am planning to buy a chevrolet cruze Automatic, but i have lots of confusion in Automatic transmission life and common issues of 6T40 transmission. Could you help me to decide whether Automatic or manual.
