What we calla double chop in N.Ireland

Good job

Record video poooooooooooorrrrrreeeeeeessssssssssssssssstttttttttttttttt

On my small 3 cylinder kubota i did this and it broke my block beware , it made a hole into the water passage. Dont know if the biggger engines are ok with this method, but im going to buy the tool next time

Nice

You set pre cut ones in and taped down the edge

Them must be some different metal than what I'm working with this shit ain't no where near doable

Awsome work

Makes a whole lot of sense how an engine can just explode from a little bit of cosby in a can 😂

Bucket latch indicator great idea.

Just finished up taking sleeves out, took maybe 5 minutes. Thanks alot!

Anyone know if this method will work on a chevy 5.3 ls motor?

woo pants shitted

Don't use finished liners they should be unfinished and machine honed to correct tolerance. A finished dry liner won't be true in tolerance.

Never remove a dry liner that way pressed or pulled out preferably pressed.

What glue did you use.

👍

Where did you het the auger screws from?

OOOO get back in that tractor where its warm .lol

Kallstrom Sweet Corn has a Harley picker and Harley rake , we just love it here in Ephrata , Wa . It's a great picker ! ! !

Great tip!

How hard was it to drop the pan out of this tractor? I have a 135 with low compression in one cylinder. Wasn't sure if i could do an in chassis with the pan being a structural member. Thanks!

Can you accidentally saw the "pusher" or is it locked out from that somehow?

I’ve never done this. I am amazed that the sleeve is that thin. I thought it was like a thick piece of pipe! Thanks for sharing this.

Wow, I got that same screw driver. Mine was from a company called Apollo back in the 80s. It's pretty magnetized right?

Thanks! It’s works!! Be careful tho. Found out they last rancher used a torch and gouged the fuck out of the block, but it lasted last time FML

nice picker

The sleeves you installed, were they semi-finished? And if so did you have to hone them prior to piston installation, thanks.

Nice looking highland’s

Also I'm working on a AG 3.152 having problems finding a exh valve seat anybody know where I can get some?

Tried your way of removing sleeve and it worked exactly like you did yours thank you.

My friends didn't believe me what I did on my 1hz engine. Exactly the same as you. Just cracked them out. Unfortunately my liners were 1.5mm thick. Took 1h each....done 6.

Hello

What if the liner is cast iorn..?

👍👍👍

How many rpms works?

what if the liner is not bad and u what to use it back in the copy of the engine

Even in iraq we don't do this 😂

Saludos donde compro repuestos originales que me de 10.000 horas de trabajo

Has. Anyone ever tried this method on an 8n? Haven’t tried yet, are sleeves thicker?

Nice machine.

Does this work on all motors like a Cummins or say a Perkins motor on a cat 220?

I will try this method on my old 1941 Ford 9N. Thank you for sharing this video!

Boy that was neat. Not going to buy or make a puller...

I was trying to remove the sleeve in my old Toyota for 3 days, making and using my own tools. I wasted hours and hours. I hadn’t seen this video but as soon as I saw it I went outside and removed my sleeve within 1 hour. Thankyou Thankyou Thankyou

I used eather a few times for emergencies but I plug everything in when it’s cold

Nice, sounds and looks good!

Its that easy don’t need to take of ur wrist clock

appreciate the stick control button explanations; question- is the rate of seop/cut of the cutting bar adjustable? I have seen other videos and it cuts thru a lot faster than yours. Is it self adjusting as it gets dull? Thanks

Did it score the block on the way down?