I found out my detergent has salt already in it, but since I have a bunch of salt packs, I decided to still use it, but at the lowest setting H01. The two red squares on the test strips indicate I should use H03, but I assume that is if the detergent does not have any salt in it. Is that a sensible approach?
If you are using all-in-one tablets/gel pacs, you can usually turn off the salt resin unless your water is very hard. However, if you notice hard water deposits on your dishes, you should increase the setting.
Can you please elaborate? I am not sure I understood your problem. If you have an undercounter dishwasher this video is not for you. In that case there are 2 screws at the front of the kick board that adjust the back feet.
You probably don’t need a new pipe, but a quick-connect adapter like the one in the video. They commonly go by the brand name Hozelock, but off-brand ones should work just as well.
This wasn’t my machine, so I’m not sure how much time Extra Dry adds. I don’t recall it drying even a small load completely even after multiple runs of the dry cycle
I purchased one vacuum cleaner. It has a problem. The attachable extension pipes are not a good design. They do not get fixed firmly. Every 2 or 3 minutes the tubes get loose and fall apart. I reported the problem to the customer care, but they say that is how it is designed. I feel I should not have purchased it
I've had this problem on multiple vacuum cleaners so far. On one the lower tube even cracked because I kept trying to tighten it. I'm afraid you'll have to use a stopgap solution like duct tape if it bothers you too much.
Wash&Dry 60’ is a wash+spin+tumble dry cycle but is designed only for very small, urgent loads like a couple of items. Please read the owner’s manual for details.
If i have sound insulation around the whole dishwasher, how do i test if it is leve? I can’t put a level on top. And doesn’t it need to be leveled in the cabeinet, not once it’s slid out?
This video is for freestanding dishwashers. It sounds like you have an undercounter dishwasher. For those machines, the front feet are adjusted as in the video but the back feet are adjusted by turning two screws in the kickplate above the front feet -- and as you said -- after the dishwasher is already in place. You can keep a spirit level on the top of the door. I'd recommend following a different video as this one isn't for your type of dishwasher.
Hello, the fluff clean lamp should illuminate after every 10 cycles - this is normal. If it’s illuminating more frequently than that, potentially you are looking for the wrong lamp, or not running the Fluff Clean cycle correctly - for example check once that the jog dial hasn’t become miscalibrated - a simple test would be to turn the dial to off and check if the display turns off. Otherwise the state machine that counts cycles might have been broken and you will have to contact Bosch support, which is the best option anyway. Thanks Tic Tech Toe
Hello, the particular model shown in the video doesn’t have an on-off button. Can you please let me know the model number (E-Nr, NOT the serial number which is confidential) of your appliance? It should be on a label on the rim of the door. Alternatively contact Bosch support who I am sure will be able to help you with this.
Please contact your local authorised Eureka Forbes workshop for spares and service. Tools માટે કૃપા કરીને તમારી સ્થાનિક Eureka Forbes વર્કશોપનો સંપર્ક કરો. [Google દ્વારા અનુવાદિત]
Hi Nidhi, To the best of my knowledge, this model preselects drying time based on weight at the start of the cycle, instead of recording moisture in real time.
Default setting in bosch for salt is 4. When i tested the paper strip only 2 squares turned red. So i thought salt setting can be reduced to 3. But tho my apartments has WTP softening system ... TDS is 1100. So shud i continue with setting 4 or decrease to 3 or increase to 5 ?? How much grams of salt will each setting take?? Same doubt in rinse aid. Default setting in machine is 5. How much ml will it consume??
Hi, apologies for the delay. Best ask the Bosch support team for salt/rinse aid quantities per unit setting. An output of 1100 ppm CaCO3 from your external water softener is quite concerning, however that doesn’t seem plausible because on the Aquadur test strip supplied with BSH Group dishwashers, a reading of 2 squares indicates a CaCO3-equivalent of 150-250 ppm which means your external water softener is working fine. You should proceed with a salt setting of H:02 or H:03 (the readings on the test strip are too discrete to specify which one). If your hardness is indeed 1100ppm after using an external softener that is quite concerning; you would be well past the 890 ppm upper limit for even the maximum H:07 setting on your dishwasher and the heater would soon start to develop a limescale crust. However 1100 ppm is also comfortably above the lower limit for all 4 squares on the test strip, so unless the test strip was defective or you didn’t fully immerse it in the water sample, it doesn’t seem likely that you would get only two squares.
@@TicTechToe hardness strip test showed 2 squares turn red. TDS is 1200 after water softener. However Salt and TDS are different. Though TDS is 1200ppm still the salt level is less
@@chinku84 Sorry I didn’t realise the 1100 was for TDS and not hardness. You should decide the salt level based on hardness and not TDS. Hardness only depends on calcium and magnesium salts and not others which are included in TDS. Use the strip reading.
If you don't have the cable your only luck is Wireless Direct. This is an ad-hoc network the printer sets up. 1. Turn on the printer, let it initialise, and after a while search for Wi-Fi networks on your MacBook and you might find a network named HP-Print-**-LaserJet-1025 (** is a random two-digit number). Connect to it. Skip to step 3. 2. If you DON'T see the network, press the wireless button on your printer once and after a while the lamp should illuminate with a blue pulse. You should then see the network; connect to it. 3. Open System Preferences > Printers and Scanners, click the lock icon to modify settings, click the little '+' icon under the list of printers, select your printer in the popup window (the connection type should be Bonjour), select AirPrint for the driver (or the full-feature driver if you have some time), click Add :-)
Follow the instructions at 1:28, only instead of H:0x, keep pressing Eco until the LCD display reads r:0x. Then keep pressing prerinse and you should be able vary the volume of rinse aid dispensed.
Regrettably, I was indoors at the time and didn't bother filming the accessory in action out of doors since that would be inconvenient at the time. This has been a common request over the years. I've now lost the black 35mm to 32mm diameter conversion tube that's used to attach the spray jar to the main hose, or I would've done a follow-up video :(. I will if I find it. Thanks for your understanding.
If you tried the steps in this video and your Roomba still doesn’t dock, please contact iRobot’s official support channels instead. Could be a failed part.
I've started using Bosch dishwasher. My dishes are getting dried up without any issues. But I notice that the racks and the walls of the dishwasher are dripping wet although the Extra Dry option is selected. Can someone please tell me how to fix that? I've kept my Dishwasher in my kitchen balcony and there's no way I can leave the dishwasher door open overnight. During the day, I can afford to keep it open for not more than 20-30 minutes.
You have no reason to worry. Residual condensate on the walls and door after the cycle are perfectly normal - it's a characteristic of European dishwashers that use condensation drying rather than the element-assisted heated drying that American dishwashers use. If you can, leave the door slightly ajar (not completely open but not clicked closed either) between cycles so that no nasty odours develop. It's not entirely necessary, though.
Love thisBISSELL PowerFresh Steam Mop esp during quarantine when I've got enough to do/worry about. Suction is great, works on carpet, hanwood, rugs. Battery life = approx 2 hrs. Can run at night & didn't wake my child (our bedrooms are on the 1st floor). Not as loud as a conventional stand up. Love the ability to connect to my phone/Alexa.
As long as you remove the orange mesh filter, I believe you can. However it's best to use the gasket if you have it since the user handbook suggests it. I won't be responsible for any potential damage that caused by skipping the gasket. I have not personally tried using the vacuum without the gasket, however another user in the comments below has suggested that this works.
Sir by mistake I forget to remove the filter and I was cleaning carpet with water after some minutes I realise that the filer is in vaccume cleaner it's became so wetted now I am worried about it what will happen will it damage please tell me and sorry that my english is not so good
The HP LaserJet Pro CP1025 cannot be connected to the Internet, only models with the 'nw' suffix (CP1025nw) like the one in this video can be connected to the Internet via Ethernet or Wi-Fi. (n=network, w=wireless)
