Thank you for a helpful video. Any ideas if the Smart Wash, Normal Wash, Delay Hours, and Cancel Drain buttons are all flashing? I feel like I have to press an ever-changing rocket launch sequence to either drain or continue, but it stops mid-cycle (more like 2 min into the cycle).
Hey brother. Thank you for this process. SUPER HELPFUL. Shame that Kenmore makes it this difficult to get in there and clean it out. More examples of how big corp wants their products to fail after so long, so we can keep buying.
Thank you! Wish I had the torque specs for those 2 screws for the ignition cylinder lock and the one big screw for the steering wheel. I jus tighten them real good.
Great video. i was procrastinating on the cleaning , but this helped to get it started. The one piece that was not clear: does the washer go under the top spinner or above the filter? your video shows under the spinner , but not sure if this is correct?
The fact that you didn't show the process of removing the rear with the safety pins suggests that this part is very difficult. I took the whole thing apart (you can take the plastic off first BTW), completely stalled at that point and could do nothing but put it all back together again. Thumbs down.
Thanks so much! You made it so clear how to clean my dishwasher. My dishes were not getting clean. ...always gunk left on the dishes! Now I know why. This saves me a whole lot of money! Much success to you!!
What if you replaced all spark plugs and ignition coils and you still have misfire codes and smoke from exhaust. (I used a fuel injection clearer also because I was told they were bad/dirty)
Thank you very much. I tore apart my dishwasher and running a cycle now. See if it fixed… My only complaint is you skipped on how to put the end tabs back on the upper rack!!!!! LOL honestly that was a hardest part of this whole damn thing.😂😂😂😂
You have your cylinder numbers wrong. The are 1,2,3 and the back of engine left to right and 4,5,6 left to right on the front. By front and back I'm referring to the back at the firewall and front closest to bumper..
Giving a thumbs up, but it would have been helpful to explain what you did between 6:00 and 6:10 to make the bottom sprayer fit. I finally figured it out. You do NOT push the part you turn by hand down into the hole. Just set it there, sitting on the top edge of the hole in the filter, then place the top/back pipe on it, and the bottom sprayer will fit right on.
I'm going through EXACTLY the same issues on my 2007 Honda Pilot right now! When i'm on the hwy & maintain rpms averaging 1500-1800 for more then 5sec my engine light starts to flash & i'm getting misfire issues. I live on top of a very high mountain & if i try to go up in D it starts to misfire. But if i switch to D3 no misfires. My mechanic replaced all my plugs w/iridiums & all 6 ignition coils roughly 2yrs ago but now the light keeps coming back on & my mechanics reader & Auto Zone reads misfires on #5 (middle front). So what is the exact name of these springs or part# please? I'm going to have these replaced once i get that info from you & i'll let you know the results. Thanks!
I had the same issue, i took some needlenose pliers and gently turned it to the left, it rose up and was able to spin freely so i could get the bottom arm on and tighten it.
The dishwasher in my apartment is this exact model, and it had been giving me problems. Thank you! Because of your video I didn't have to call management and arrange for a repairperson to visit.
Thanks for the video! My daughter bought the sidekick 4 years ago. Her lid broke - I think the silver part has both ends on it still. The underside of the lid broke right under 1 of the pins so the latch doesn't latch. Crazy, right? $200 for the entire lid assembly?! I bought a new open box sidekick on craigslist for $200 (and 6 hours of round trip driving to get it... I just can't pay or have family pay $200 or even $100 on ebay for that part). We'll take the lid off this on, put it on hers. (I found your video when looking for the right way to take the lid off). And sell parts from the whole unit on ebay / keep it for spare parts for her?! Wondering how your fix has worked out after 4 - 5 months? And yeah, you mention - this IS a common problem? Weasels! I always wonder about whether to get an extended warranty : ) And the plastic weld... from your experience, that's different than the typical 2 part epoxy (gorilla, etc.)?
