Hey everyone! My name is Leo, I'm an ASE Master Certified Automotive Technician and L1 Engine Performance Specialist from the Atlanta area. If you find my information useful, then go ahead and subscribe and follow me on my journey!
Have just bought a 2017 one of these... picked up yesterday and on looking around the car today noticed this case not sitting flush, moved it and now seen that this manual thing is broken?? Now whilst i know I will be contacting the garage... I an wondering how much it is to replace?? I'm UK
Question for you my friend. I have a 2014 Dodge Charger SXT. Car suddenly wouldnt start and after testing some other components (relay, The fuel pump wasnt coming on when putting key in the "Run" position. No sound at all coming from pump. Changed the fuel pump but NOT the wiring specified in your video. My car has been running for a week but now same issue We didn’t change the wiring on the Delphi pump?
The pump you replaced was Delphi?? The pump should have come with a pigtail connector. Did the car crank after you replaced the pump without the harness?
This video definitely helped I didn’t know I had to switch the two cables that’s why I was getting told no gas on my dash and flashing gas light when I had half a tank a😅definitely helped a lot and was able to get it running thank you!!
Well every other fitting I inspected was perfectly clean and dry, this one had a darker oily appearance, and was attracting dirt because of the leak there. The charge valves were in good shape too, the vehicle has been great ever since
@@RodriguezRepairs the one I got now is the GM P/N 25191144, but the tensioner will not go down to the second bolt. Got it from the dealer, but I don't think its the right belt. Thanks for the reply!
Well while you can release the gas in the air, its not a legal practice due to "polluting the atmosphere" thats why recovery systems exist, so the refrigerant can be stored in a suitable container
Just had the battery replaced in my ‘03 Camry and was experiencing low idle rpm leading to the engine stalling. Tried this and let it idle for about 15 minutes, it worked like a charm! Thanks!
Help! Boot loop My ArtiDiag 600S went into a boot loop and I can't reset it. I've tried the reset button but nothing happens. Please help! Great review, by the way!
So I replaced all actuators but it's still not blowing cold in driver side but is cold on passenger!! Could it be the blower motor or is that not the case at all
You replaced all actuators? both temp actuators also? The blower motor will not cause different heat temperatures on both sides. Can the both sides switch to "HEAT" normally?
Does the actuator just come off…can’t seem to get mine to budge…I can feel that is “loose” at the three of the bracket screws, but won’t pull off (the new one separated ok)…any tricks?
10:07 everything went blurry for me when you showed us that tool cuz i definitely don’t have that lol glad incan use a flat head screw. Still following to get it fixed so far so good 🤞🏾
@@RodriguezRepairsi put everything back. But when i started the car and put it it in drive, the car stalled on me. I dont know what i did wrong. Feel like there is a plug or something i missed 🤦🏿♂️
I changed my fuel pump the aftermarket pump did not come with a harness when I turn the key to run I can hear the pump turn on but I still get a crank no start would my wires need to be swapped around if I can hear the pump? I’m looking at the dodge wiring diagram & it’s the updated way
Did you have to do anything special to get the new actuator on? For some reason I cannot get mine onto the pendulum/the white plastic square around it.
In. 2009 Toyota Venza 4 cylinder fwd 1.7L setting the parking brake alone will not allow me to put the car in drive. The sticks started feature will not allow it. This technique is a major failure!
I have a 2016 dodge charger RT scat pack. I changed both fuel pumps and change the harness. I get a crank but the car rough idles and then dies out. I got a fuel level sensor 2 circuit high voltage code and also a throttle actuator control system sudden high airflow detected code… please help I can’t find any solutions anywhere!!!
Hey, if you happen to see this, would you know if those two acuators are the same part number/interchangable? Thanks for the video, one of the best I've seen. Hope the day finds you well.
Hey there! they are two different part numbers for the driver and passenger sides because they both bolt differently. The passenger has a Bolt hole in the middle and the driver side doesnt not
@@RodriguezRepairs Sorry, maybe I should've been more specific. I was referring to the two actuators you showed side-by-side in the video, (the blend door and mode door) on the drivers side. They seem to be the same part. But thanks again, you're greatly appreciated ✌
Thank you for this video!! Before I go buy a replacement bulb I have a question. My driver side light seems to be out as well.. but if I push it manually, it comes on.. it just doesn't work on either switch. Do you think that's a fuse thing?
If you push it manually and it works, then the circuit is active and the fuse is not blown. Do you mean when you open the Doors, the dome lights do not come on automatically?