1:11

Подписаться 7 тыс.

Просмотров 29 тыс.

50% 1

I Trued my crankshaft and just wanted to show you how I was able to get it nice and true.
Link to 2STROKE STUFFING video on truing (Shows you where to hit) • CRANKSHAFT TRUING MADE...
Links to my YZ250 full rebuild...
Part 1 • 1:11 YZ250 Full 2 Stro...
Part 2 • 1:11 YZ250 Full 2 Stro...
Part 3 • 1:11 YZ250 Full 2 Stro...
Part 4 • 1:11 YZ250 Full 2 Stro...
Part 5 • 1:11 YZ250 Full Motor ...
Donate Race Fuel link... www.paypal.com/donate/?hosted...
Thanks for watching!
upallnight91@hotmail.com

Хобби

Опубликовано:

6 дек 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 59

@user-fy2mm4sb7y 7 месяцев назад

That’s crazy how that little drop threw it off that much. Again,thank you for sharing your knowledge brother 👍👍👍

@UpAllNight91 7 месяцев назад

For sure. I'm thinking it was just the perfect hit at the perfect angle on the perfect surface lol. I was surprised too

@robertovr9976 3 месяца назад

Great video, I had always wondered how they true those crankshafts, thanks a lot!

@UpAllNight91 3 месяца назад

Your Welcome. Since then I have trued in a few more. Its actually kinda fun lol

@michaelevans9568 Год назад

I rebuilt my Ktm 300 crank my self with a H F press. made a truing stand out of my engine stand. It was easier than I thought it would be. I have around 20 hrs on it now and it runs great. I used a 2lb brass hammer

@UpAllNight91 Год назад

Thats cool! Good job. I have not rebuilt a crank yet, only trued. But I do plan to try one here soon. I have a 2 ton press, do you think that would be good enough?

@montana2strokeracer Год назад

Good Job, think you would benefit from a bigger brass hammer though, I have been truing cranks since the 70's and normally use a 3 to 5 lb brass hammer. The greater mass will move the webs very easy, while holding in your hand. Very good tutorial enjoyed the video.

@UpAllNight91 Год назад

Thanks! Thanks for the tip on the heavier hammer. I used this hammer because I seen another video where he trued the crank with a hammer at this weight. But I bet a heavier hammer will surely make it easier because I had to smack the crap out of it with this one! LoL

@barkeep25 Год назад

Good stuff man, sent my old crankshaft to crankworks a few weeks ago for a rebuild. I'm going to try and replicate or at least measure it the way you and 2strokestuffings did when it gets back. Great tip on positioning too! Man I need to learn to weld!!

@KaiMiller Год назад

how much in total did that cost??

@UpAllNight91 Год назад

Yes I wish I knew how to weld too. Luckily for me a good friend of mine who is retired is a great retired welder and does anything I need. Its like an art. I surely would want to check the crank when you get it back, just for peace of mind and so you know!

@barkeep25 Год назад

@@KaiMiller can't remember exactly but w/ shipping all and all about a $100 less than a new aftermarket one, like hot rods, im using a pro x rod.

@KaiMiller Год назад

@@barkeep25 thank you man!

@haseebqureshir9324 Год назад

Yes ❤ I have also this work you can see also my work on RU-vid

@rickknechtel5093 5 месяцев назад

Well done

@UpAllNight91 5 месяцев назад

Thank you Sir!

@fenderbender2446 Год назад

Brass hammers work aswell and are a lot cheaper if your not beating the crap out of it. You should take a shot at rebuilding a shot crank rather then replacing and try trueing it. You can do cranks 125cc or smaller with your 20t press. Would be cool to see. 👍

@UpAllNight91 Год назад

Is the brass hammer as soft on the crank as a copper one is? I do plan to try to rebuild a 125 crank at some point. Especially because since covid often times cranks can be on back order so rebuilding cranks is sometimes the fastest option, especially with the ktms.

@gowengetter4599 9 месяцев назад

Great video. Just sub. Do you install your main bearings in the case, then install the crank? Or do you put the main bearings on the crank first?

@UpAllNight91 9 месяцев назад

Hello. Thanks. I like to install the crank bearings in the case first. And then install the crank. I freeze the bearings and heat the case some to help them slide it in. And then I freeze the crank and put a little heat on the bearings to the crank slides in the bearings easy.

@user-me1bg1tg8f 5 месяцев назад

Good job chin up mano

@UpAllNight91 5 месяцев назад

Thank you Sir!🙂

@NotAMotoVlog Год назад

Sent mine to crankworks a month ago. I'll probably try this next time. Gonna miss first race of the year not having it back in time oh well.

@UpAllNight91 Год назад

Oh crap that sucks. Thats like cylinder replating, can sometimes take months. With cylinders I try to only send spares out so I can keep riding. Unless there is no spare and no available replacement then I just have to wait lol

@NotAMotoVlog Год назад

@@UpAllNight91 what was crazy is powerseal did the cylinder beginning of January in about a week! So much for just a top end, had to rebuild everything.. Hopefully just top ends for a couple years now 🙂

@UpAllNight91 Год назад

@@NotAMotoVlog yeah. A week is good. I wish they always got it done that quickly. How much did powerseal cost if u don't mind me asking

@NotAMotoVlog Год назад

@@UpAllNight91 it was $265 for the replate, but I didn't have any cracks that needed welding thankfully. I think millennium was quoting me around $300. Powerseal did great work, would definitely use them again. Whole cylinder got vapor blasted too from the look of it

@UpAllNight91 Год назад

@@NotAMotoVlog nice! Ok. I have a spare 125 and 250 cylinder I plan to send out for a plating. Thanks

@gabrielalvarez9570 8 месяцев назад

Imajine if tou would have measured runout at the end of that shaft 😮

@dc6233 5 месяцев назад

Exactly. It's his first, cut him some slack 🤣

@UpAllNight91 5 месяцев назад

@@dc6233 True and thanks. Honestly this crank that I trued ended up measuring better than the brand new one I put in my bike from yamaha. Both measured on the same spots. Next time I wil try putting it further down on the stator side. However on the crank main gear side theres no further down I can go really.

@bobybobbison 10 месяцев назад

Harbor freight has the brass hammer but they are not very heavy but they work.

@UpAllNight91 10 месяцев назад

Thanks. Thats good info.

@whiteman3075 Год назад

Iv seen a guy that does them smack it on a solid block of wood to align it just a little at a time

@UpAllNight91 Год назад

Thats crazy. I bet it works though.

@microsoft790 9 месяцев назад

I’m really nervous to try this but I have no choice if I want to get my bikes running. Luckily I have a trash crank to practice on. Maybe it can even be fixed if I machine it.

@UpAllNight91 9 месяцев назад

I know the feeling. It can be scary. Make sure to use the correct hammer and take your time. A junk crank to try on first is surely a good idea too.

@user-me1bg1tg8f 5 месяцев назад

Hey man if they don,t find you handsome at least they will find you handy

@UpAllNight91 5 месяцев назад

Hahahah! Thats the truth!

@bramvermaat1453 7 месяцев назад

How vital would it be if the two supporting beams for the crank aren't exactly the the same height?

@UpAllNight91 7 месяцев назад

As long as you can get consistent measurements it should be ok.

@user-rj4wc5gq8x 4 месяца назад

Could you possibly use a framing square or speed square??

@UpAllNight91 4 месяца назад

Yes, anything can be used as long as its held steady.

@govt.graduatecollegetobate5442 2 месяца назад

Why do you guys hit it with hammer? How does it help to make its rotation smooth?

@UpAllNight91 2 месяца назад

Hitting with the hammer is to spin one half of the crank from the other half to try to get both sides on a equal plain

@brianquintero3028 Год назад

Can you send me a link for the truing tool can't seem find it

@UpAllNight91 Год назад

Which tool? The dial indicator, or stand, or?

@brianquintero3028 Год назад

Both

@UpAllNight91 Год назад

@@brianquintero3028 the dial indicator and stand was bought from harborfreight.com and the truing stand I had a friend build for me. They do sell trueing stands but they are usually not check so if you can fabricate one its better. Even a quick make shift one will get it done

@homersimpson6348 Год назад

Can I pay you to rebuild my crank, I have all the new parts already I just need the work done

@UpAllNight91 Год назад

Hello. Sorry I don't rebuild cranks. I can true them but don't have any experience in pressing out rods and putting new ones in. Sorry

@kylepeterson Год назад

put the indicator at the start and end of the taper, after you think it's true

@UpAllNight91 Год назад

You mean where the crank pin is at? To help keep track?

@dc6233 5 месяцев назад

Please, get rid of that Harbor Freight digital guage, it doesn't show enough digits accurately. Just get a regular dial indicator in thousands (.001) where there's a needle you can watch when roatating the crank. And, move it out further on the taper, you'll find it's out even further out than where you are measuring it at. 2 minutes into this video you can see whay a needle is far easier to use accurately: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-t4W9RXZgY1g.html

@UpAllNight91 5 месяцев назад

Hello. Thanks for the tips. I'm sure there is always better ways to do it. I'm not looking to geek out on truing too much, I just needed it as good or better than how they come brand new out of the box in good shape. Bike has about 50 hours on it so far and is running great. I do have a older but analog dial indicator though, maybe I will try that next time. I know it gives you better resolution but as long as its falling tight towards true thats my biggest concern.

@dreece2000 2 месяца назад

Shit Man I doubt this guy knows what he’s even talking about. The harbor freight dial will be fine. If this was an engine that cost as much as your house or was in an airplane things might be different. Thanks for the video

@user-hy1gf4iy3u 4 месяца назад

Will you please send it to me to put in my bike I um like hit mine with a f good size😮‍💨 hammer I'm a big dummy it's possible way out of wake I'm not even joking about it 😅😅

@UpAllNight91 4 месяца назад

😄 I already put that crank in a friends bike. Still going strong today too!