Good video, good thoughts. Always interesting to hear how other people use their saws. Thanks for the info. You mentioned having issues with husky chains getting loose almost immediately. I noticed you didn’t pull up on the nose of the bar when tightening down the bar nuts. If the nose of your bar tilts up while cutting your chain will get loose. Next time you run a husky try lifting the nose while adjusting and tightening the chain.
I'm in the same boat......I'm building a custom MS460 for my Daily, and leaning towards a 25".......I already have 2 Farm Saws with 20" bars.....also have a vintage muscle saw with a 28" bar if all else fails. So I think 25" Light Bar would be perfect. I've also realized there is No "do it all" saw.....you need multiple saws for different occasions. I'm also on the East Coast, so tree sizes vary, and just had to drop a 40" tree last month, and good thing I had a 28" Bar, kinda saved the day.....but it's not often I use it.
I just got my 500i and went with the 28. I love it. That said, after watching your video.... I think I may have to get a 20 as well! (PS... also right here in Hudson!)
I'm over 6 foot and usually have a 24-25" bar, my 500i came with a 28" and I'm very happy with it. Can't think of any reason to go for a 20" at my height.
Good video. I too run 20 and 24/5 36 . Tsumura Light. 362 C, 046, 660, 661. Regular ES bars and Canon. Depending on what cutting. Best equipment ever are 2 nephews w strong backs!
Thanks for the video. I’m about to buy a new 500i and have been debating between 20” lite and 25” lite bars. I’m already leaning towards the 25” but I’ve been happy with my 20” bar on my old ms440. I think I’ll bite the bullet and go for the 25” though. Cheers from Ontario!
Bending over is fine. Bar length should be based on the average size of the timber you’re cutting. Short bar makes for a faster cutting, better balance and more manoeuvrable saw.
I buck with a 28” on my 362c and fall with 25” on my 661c. I can cut all day and not pay for it later. Holding a lighter saw with a longer bar a lot more than falling a tree.
It’s funny being out west and listening to someone debate between a 20” bar and a 25” bar. That saw would have nothing less than a 32” here. Just a difference in geography.
True. There is almost no virgin forest here, and no one lets trees go to their maximum size before harvesting. Plus, the eastern species do not get as big. That having been said, tulip poplars have been known to get to a 10' trunk diameter, and I have seen some oaks and walnuts with 6 foot diameter. And it takes more power to cut hardwoods.
Hello. Forgive me if I am wrong, and for sure you with have tons of experience over me, it seem to me my Stihl MSA300 with an 18" Light 04 bar with be maybe faster that yours MS300I at least on the thinner logs. I maybe wrong but is my impression.
I like a 20" bar with my 500i. It cuts a little faster than a 25" and weighs less. And I cannot lift any log the 20" bar will not cut. That having been said, I needed to buck a 23" hickory log a couple of days ago. I could have done it with my 20" bar but decided to save time by switching to my 25". But the resulting logs are way to heavy for me to lift. I rolled them into my loader bucket and put them at the bottom of my seasoning row. I will have to pre-split by hand when that time comes.
@@timbertimeoutdoors9836 In my case with Stihl MSA300 if I go with a bar above the 16" or 18" recommended don't I lost battery run time and decreased the cutting speed?
I got a Stihl 500i with a 25” bar. Really wanting to go to a 20” bar. I grew up in Newfoundland Canada where everyone got 16” bars and that’s what I used until I moved to Alberta. Now I like the 18” bar on my 261 and wanting to try a 20” on my 500i. Debating if I should just buy a 400 with a 20” bar. I find cutting wood in the pile with the 25” bar is uncomfortable and harder to judge the tip. Also hate how long it takes to file the chain on the 25”. It’s really what one is use to.
I know exactly what you mean. I have a love hate for this 25" bar. I do like it for standing up and bucking rounds. Like the video shows, it is a much more comfortable position. However, I don't like the 25" for other types of cutting. Its just too big. The 20" is a nice balance for all work. Its funny you mention the 400 with a 20". I am also considering doing that. I have both ends of the spectrum covered with the 500i/25" bar and the 261C/18" bar. I think the 400C/20" bar would be that perfect mix between power/reach and weight for general cutting. Its hard to beat the speed of the 500i but it can be a lot of saw for delimbing or just some quick cuts. I will usually pull out the 261 for that but it has its limits and is a bit slow for me now that I have seen the speed of a big saw.
I totally agree with you. I’m only 5ft 8 and I liked the 25” bar at first but now I’m not liking it as much. It’s got it’s place. I’ve cut down a few trees where it came in handy. I like my 500 but wish it was a 1/2 pound lighter or a tiny bit smaller. That’s why I’m thinking the perfect saw might be the 400. Good for bucking and limbing. Then I also have each bar length. 18” 261, 20” 400, and the 500 with the 25”.
I think my bigger saws are gas hogs! My echo cs7310 p and my cs800 p those two cells are definitely gas hogs. Now the new Stihl chainsaw ms400 cm 24-in bar. is right there with my echo 590 timberwolf 20-in bar. on fuel consumption.
The bigger saws burn more fuel per hour but they also cut more wood per hour. In my experience, the 500i actually uses less fuel than my previous MS441C per unit of cutting. My 500i uses a tank in 35 minutes when kept busy but cuts maybe 25% more wood than my 441C did in 45 minutes, which is how long it ran on a tank. So, it is actually more fuel efficient.
Lol. You must have had some cheap home owner Husqvarna’s if the chain loosened up on them or more likely a brand new chain that stretches like all new chains do 7:19. I just got my first Stihl a 500i 2 weeks ago but it is nothing special compared to all my 5 series Husqvarna’s XP pro models. You Stihl guys kill me😂
@@timbertimeoutdoors9836 thank you for being honest. If you get the opportunity try a 550XP Mark II (best 50cc class saw hands down) or a 572XP which is a bit heavy but built like a tank and will last forever. Time will tell if my new 500i is as good a saw as my 4 5 series(550, 562, 572 and 592) Husqvarna’s.
run the 25 inch on my 362 don't think i would ever go any shorter for fire wood can't beet standing up straight while cutting wood although a 500 with a 25-28 inch bar wood be nice