No video :(

1966 Mercury Merc 110 9.8hp Gear box rebuild start to finish A real How To if there ever was one

Подписаться 23 тыс.

Просмотров 11 тыс.

50% 1

This Mercury 9.9 had nothing but water in it. We are going to fix that.
Parts can be found at the following websites:
www.marineengine.com
www.oldmercs.com
www.crowleymarine.com
Check out the links below for tools and items used in this video:
Heat Sound Deadener Insulation Mat: amzn.to/3efMV5D
Decibel Meter, RISEPRO amzn.to/3ADimhM
Lucas Oil 10682 Marine Grease amzn.to/3TxAfXS
carb cleaner www.napaonline...
Sierra 18-7070 Carburetor Kit amzn.to/3pNtm7c
Taukealugs Battery Cable wire Lug Crimping Tool amzn.to/3Q4Kyjm
Industrial Endoscope amzn.to/3ETaAS8
Boat Flooring EVA Foam Decking Sheet amzn.to/3Qq4LRc
Circuit breakers amzn.to/3oqnJuP
Sealant amzn.to/3z25nFv
Tool kit amzn.to/3OLjEMN
Use Code 10OFFSTP for a 10% discount when you check out
Retractable Ratchet Straps 1 in x 10 ft amzn.to/3z7ayFv 2PCS Stainless Steel Retractable Ratchet Straps (1 7/8 in x 4 ft) Heavy Duty Transom Tie-Downs amzn.to/3uP2BSF 2PCS Stainless Steel Retractable Ratchet Straps (1 7/8 in x 4 ft) amzn.to/3ObBHep
BOSCH Remote Starter Switch amzn.to/3zDrKzb
Dupli-Color Self-Etching Primer Green amzn.to/3lZhrAX
VHT Engine Grabber Green amzn.to/3zHL2Uf
Helicoil 5/16-18 Inch Thread Repair Kit amzn.to/3m3rN2q
CRAFTSMAN Mechanics Tool Set amzn.to/3zHOcr7
PerTronix 1146A Ignitor for Delco 4 Cylinder Distributor amzn.to/2Y9j0ny
Mercruiser Water Circulating Pump amzn.to/3BMJRUQ
CRAFTSMAN Mechanics Tool Set, SAE / Metric, 189-Piece (CMMT12034)
amzn.to/3jOfN58
DEWALT 20V Max Cordless Drill Combo Kit, 2-Tool
amzn.to/3zkEI4N
Actron CP7527 Inductive Timing Light amzn.to/3zQeGY7
Engine Cylinder Compression Tester Kit
amzn.to/3zoaspV
Autolite Box of 4 Genuine 403 Copper Resistor Spark Plugs
amzn.to/3jL6TFp
Quicksilver 866340Q03 Oil Filter amzn.to/3kWEPyq
PerTronix 40611 Flame-Thrower 40,000 Volt 3.0 ohm Coil , Black
amzn.to/3ylZwIM
Quicksilver 816761Q14 Spark Plug Wire Kit
amzn.to/3mJv9K0
Seaworks Dual Feed Muff Style Boat Motor Flusher
amzn.to/3jsHws8
Video equipment used:
Cannon EOS M50 Mirrorless Vlogging Camera Kit with EF-M 15-45mm Lens, Black amzn.to/3tcSCTE Comica BoomX-D D2 2.4G Wireless Lavalier
Microphone System Digital 1-Trigger-2 Wireless Microphone Transmitter & Receiver SLR Clip-on Micro phone,Lav Mic for Smartphone Camera Podcast Interview amzn.to/3edmYB4
email me at rm3dcreations@gmail.com
mail me at:
RMD Creations
PO Box 387
Wellman, IA 52356

Опубликовано:

13 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 57

@BrianGochnauer 2 дня назад

All techniques worked as advertised on my 9.8 perfectly. Thanks!

@Michaelsbackyardmarina 2 дня назад

Glad to hear it, thanks for watching

@bryancory5019 Год назад

I'm following along with my "new" mercury 110 and this is perfect. I love that you show how to remove parts without special tools that cost a fortune. Tip master. Also, I was able to replicate your homemade puller using the same bolt setup you have with an existing 4 slot puller I just bought. Good for flywheel and this application. You're the man!

@DavidB-cg5hs 8 месяцев назад

Thanks for the info Michael! I'm the second owner of a 1962 Merc 400, that has been used in saltwater extensively. Even though I use Salt Away, and wash it down thoroughly, one of the parts in the gear housing have been eaten away. I'm tearing down the lower unit to figure out why my water pump is not working properly. It turned out to be the water pump cartridge assembly that was leaking between the cartridge and the stainless cartridge insert. The aluminum housing was eaten away about 1/16 of an inch, so It wouldn't make a nice seal. The whole assembly was frozen in, and thought I might need to drill it out. Fortunately, after about a week of soaking/heating and pounding down on the top of the gear case, with the shaft in a vise, It finally broke free. More amazing was that I found an old-new stock complete cartridge assembly. Was trying to figure out what type of puller I needed to remove the forward gear, and found your video. After about a minute using map gas, it popped out so quickly that I wasn't able to catch it with my hand underneath. Luckily I had a blanket on the floor. My next step is to remove the roller bearings from the gears. Hopefully you have a video on separating the gear from the housings. Thanks again for your help. David

@GregSpehar-wm1bl 6 месяцев назад

The trick with heating the case and the bearing falls right out, works great. The shifting paw has a flat side with two lobs. The case has a short wall (or a small shelf) the flat side of the paw faces the short wall. Watch when you take it apart. I was switching cases, 9.8(1970) to 7.5(1979). They are reversed, so you need to change the paw. Flipping it over looks like it would work, but it is tapered on the inside of the paw and will not seat on the shaft in the same position. Luckly I had the paw from both cases. So I just changed out the paw to match the new case. I got my bearings from a local bearing supply shop and saved money and time. To remove the retaining nut behind the prop, I used a black pipe nipple. I cut the sides with a saws-all leaving two tits to fit the slot in the nut. Then used a pipe wrench to turn it. worked great and was quick and easy to make. Good Luck All and be safe on the water.

@copperman2179 3 месяца назад

I followed your instructions and it worked exactly like you said . Thanks !

@GregSpehar-wm1bl 6 месяцев назад

MISS INFORMATION ON MY LAST ENTRY: The flat side of the PAW is not near the short wall (or small shelf). The flat side of the Paw is opposite the short wall. Sorry for the confusion. I also ran into a problem with the changing the 6 point prop shaft to the newer 8 point(prop shaft is smaller) the spline (for the shifter gear on the prop shaft) are shorter in length. So measure these if you are interchanging the two shafts. (Read previous post for motor and years)

@carlkiekhaefer4174 Год назад

Thank you for your video for 9.8 Merc. This was a very needed video. Nicely done! Not as many Mercury video as OMC on RU-vid.

1966 Mercury Merc 110 9.8hp Gear box rebuild start to finish A real How To if there ever was one

Опубликовано:

Поделиться:

Ссылка:

Скачать:

Добавить в: