Тёмный

2000 - 2006 Toyota Tundra Rear Wheel Bearing Complete Removal & Replacement Installation DIY 1st Gen 

Garage Built Hondas
Подписаться 94 тыс.
Просмотров 122 тыс.
50% 1

The process in this video should be the same on the 2001 - 2004 Toyota Tacoma and also the 2001 - 2002 Toyota 4Runner.
Wheel Bearing Set - amzn.to/3u0deBo
Bearing and ABS Tool Set - amzn.to/3OC5TS1
My Favorite Products
Wheel Bearing Tool - amzn.to/33IplZZ
Milwaukee Ratchet -amzn.to/3EtpNJp
Jack Stands - amzn.to/3lvA5A2
Cameras used in this video
My GoPro - amzn.to/2YQ3OGZ
My Mirrorless Camera - amzn.to/2HzzFFT
Decals available for purchase here - garagebuilthon...
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
/ garagebuilthondas
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for you support!

Опубликовано:

 

6 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 136   
@lukebbb
@lukebbb 8 месяцев назад
I just did my rear bearings on my 2005 Toyota Tundra using your video as a guide. I purchased the 20 ton press from harbor freight and was very disappointed. The height from the one I bought compared to yours is different. Harbor freight, probably, in a cost savings scheme has made the whole press shorter. This reduces the clearance on the bottom area. I did get it all done using blocks under the press and doing some other jury rigged stuff with the press. Just a heads up to those trying to do the same job with Harbor Freight as your supplier of the press. Excellent video!
@GarageBuiltHondas
@GarageBuiltHondas 8 месяцев назад
That's terrible. Sorry to hear but glad you got it sorted out!
@gregresch1809
@gregresch1809 5 месяцев назад
I too have Harbor freight press. I added 4X6 wood to bottom of press. Works great this way.
@paulrozecki1270
@paulrozecki1270 Год назад
Mad props bro. You made it look so easy. Have an 05 Sequoia and I’m sure it’s the same setup/procedure. Going to bookmark this video. Great job!
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I've read it is the same. This was my first attempt after watching a few vids. I wanted to make a complete video and this was actually a pretty easy process. Good luck!
@gavrandhawa9834
@gavrandhawa9834 Год назад
Best video on internet to do hilux rear wheel bearing :)
@Jaredcouture12676
@Jaredcouture12676 Год назад
The 1 1/2 pipe is going to be really helpful! I have that same press too and was wondering what I was going to do about that. Was planning on cutting some material off the flange of the tool but your idea will be more versatile for other projects. Thanks!
@georgekopsias9159
@georgekopsias9159 4 месяца назад
Thanks for putting this video together. It is very nice to see the job done live.
@Ocean_breezes
@Ocean_breezes 2 месяца назад
Great video. I'm doing the same for my 2006 Sr5 Tundra. They sell another brand of the bearing removal tool on ebay fir around $50 bucks. Works great
@thesilentobserver93
@thesilentobserver93 Год назад
Small world! I too am a CRX owner who also happens to own a first generation 2WD Tundra. 😁 Instantly the best channel on RU-vid.
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Nice! 🙏
@robertogarcia35
@robertogarcia35 6 месяцев назад
Your work is excellent. I have to do the same on my 2000 Toyota 4runner and I see that it is faster and cheaper than with a press.
@frankjin8224
@frankjin8224 Год назад
Best film for the job I reckon. Thanks buddy.
@nothanks7285
@nothanks7285 Год назад
I like the cut beam on the press... I might do that to mine. I think I'll add a couple of lag bolts with lock nuts inside, so that I can control the width if needed, and lock it down. Wouldn't want one of those beams to shoot sideways if something slips.
@chayannesaldana7530
@chayannesaldana7530 Год назад
Do I own a Toyota truck? Nope. Did I watch the entire video? Definitely lol
@nahinufreitas-xs5pq
@nahinufreitas-xs5pq Год назад
Good job bud! Excellent on the explaining and filming. Did mine exact same way as you did and came out awesome! Thanks for the video!
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Glad to hear!
@jvpapasmurf46
@jvpapasmurf46 Год назад
Excellent (know how) video, you make it look very simple, going to attempt to replace mine tomorrow,,thanks for the instructions
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Good luck! It's definitely not too difficult!
@superk4562
@superk4562 8 месяцев назад
Excellent video; thanks for posting!
@GarageBuiltHondas
@GarageBuiltHondas 8 месяцев назад
Thank you too!
@markstevens1729
@markstevens1729 Год назад
I’m about to do this job in my ‘03. Built my own set of those tools. Work begins in the AM…
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Good luck!
@mattleek650
@mattleek650 11 месяцев назад
How did the homemade tool work? I need to do this too but not sure where to get the dimensions.
@markstevens1729
@markstevens1729 11 месяцев назад
@@mattleek650 it’s a bit of a story but it did great. Basically 3-4’ of 2-1/2” sched 40 pipe, cut to 24” and 18” pcs. Weld a 1/4”+ (thick plate, I used 4”wide by 5” long) rectangle flange (I used a 2-1/8” hole saw to cut out for the axle to pass, leaves a nice reveal flange to weld to..) on one end of the 24” pc and a 3/8” flange on the other (ditto on the hole saw..), drilled with 1/2” holes on 3-1/2” centres. That one is for the bearing. The other pc, 18” gets a flange on one end and needs very robust hooks on the other. I tried bent 3/4x 1/8” bar but it wasn’t strong enough for the 12-ton press. I went to my local rental shop and they had a pair of puller bars, slotted and drilled which I was able to mount to my flanged pipe (plug-welded nut and a welded stud and nut.)Pulled the ABS ring off like a charm. Used a 2’ piece of 1-1/2” black pipe to handle the pounding/seating duties of the new bearing/ABS/collars. I bought the press a couple of years ago just for this pending job, and it is fully paid for now.
@CesarsCarCorner
@CesarsCarCorner Год назад
For my safety, I would've used two huge c-clamps to hold those pieces on the press together. Good work and I can see how much pain that job was.
@GarageBuiltHondas
@GarageBuiltHondas Год назад
That's a good idea. I was going to drill through it and use a threaded rod so I can adjust it easily. I haven't tinkered with it yet but will soon.
@CesarsCarCorner
@CesarsCarCorner Год назад
@@GarageBuiltHondas I didn't think of a threaded rod for easily removably.
@themechanic6117
@themechanic6117 Год назад
great video , really have to put in some work for that wheel bearing job .
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Thanks man. Hope you're hanging in there!
@matthewwall5958
@matthewwall5958 3 месяца назад
The top ring that you're calling the locking washer, is actually a seal ring. I'd be interested to hear if you have an axle seal leak after seating it against the abs gear like that. I did that exact thing once on both sides and both axle seals leaked like crazy after and I had to redo both sides, brakes, bearings, seals and all.
@GarageBuiltHondas
@GarageBuiltHondas 3 месяца назад
Dude, wow. One has started leaking really bad just lately. I was curious as to what but haven't had time to pull it apart and look. Did you leave a gap between the "seal ring" and the abs gear?
@matthewwall5958
@matthewwall5958 3 месяца назад
@@GarageBuiltHondas I did, because I wanted the abs gear to be centered in the hole. I don't have any clue as to whether that matters or if it's better to have them together though. So far no leaks from the axle seal though. To double check I was riding on center of the seal ring, I put some bearing grease on the ring and put it in, bolted it down and rotated a few times, pulled it and made sure the seal was riding middle of the ring based on how far the seal pushed the bearing grease back. Hope that makes sense.
@GarageBuiltHondas
@GarageBuiltHondas 3 месяца назад
Thanks so much for posting this up. Really great to know. When I get to look at mine, and hopefully fix I'll respond back here to you and let you know what I found and maybe the same fix will help me. Yes, everything you said makes perfect sense. Appreciate the info Matt, really nice to hear these kinds of experiences!!
@Ocean_breezes
@Ocean_breezes 2 месяца назад
The distance from the abs locking ring to the brake housing is the critical measurement here. That's what seals the entire axle assembly to the axle housing. There are other videos that show you how to make sure the seals line up correctly, distance wise. Maybe measuring the distance from the original axle end at the splines to the abs "locking" ring is the best measurement
@MsJostock
@MsJostock Месяц назад
With the 4Runner 3rd gen you turn the “locking washer” upside down, so that the curved side is to the bottom, that way you have more sealing surface. Because Toyota redesigned some stuff this is a new solution, don’t know it’s the same with the tundra but looks identical.
@bigtay522
@bigtay522 Год назад
Outstanding instruction. Thank you..
@Baebon6259
@Baebon6259 Год назад
I put a layer of bearing grease to help push things down easier.
@plopez9152
@plopez9152 4 месяца назад
No need for bearings but now I want to replace them lol any one do the upgrade on the front discs on the tundra? Looking for videos. And came across these gem
@TheXbdon11x
@TheXbdon11x 7 месяцев назад
This videos helped a lot! I bought a 1.5” tube and it is too tight. I can not put the bearing in… trying to figure out another method to press the bearing in
@An9el10-22
@An9el10-22 6 месяцев назад
It's a ridgid pipe. .I did it.
@TheXbdon11x
@TheXbdon11x 6 месяцев назад
I ended up just buying the right tool from eBay. Only $30
@bryin99
@bryin99 Год назад
Fantastic video. A+ Job about to do this on an 01 Sequoia
@hoss1988
@hoss1988 Год назад
Meow! Well done 👍 ima do the same but gonna weld me a country boy version of that tube thingy
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Nice
@florpdorp7190
@florpdorp7190 9 дней назад
2:55 Wait he still has his parking brake?😂😂
@themechanic8195
@themechanic8195 11 месяцев назад
Excellent video, im fubar and will try a used axle 1st, then ultimately take the axle to a shop. FyI mine sounds grunchy, vibrates and increases noise with speed. If its not the wheel bearings then the only thing after would the differential :(
@GarageBuiltHondas
@GarageBuiltHondas 11 месяцев назад
Hope it's just the bearings!
@themechanic8195
@themechanic8195 10 месяцев назад
Yes, pulled the axle, driver side, and crunch crunch, bearing shot to hell. Will get local shop to remove the old bearing, and I'm so nervous that they might get the distance of the abs-ring/retainer that I think i will do this part myself with a long pipe. NOTE: The final retainer collar, in front of the ABS ring is acutely the sealing surface for the inner axle seal!!!! They should have called this part an "axle seal ring" or something like that. Any hoooo others have marked the new retainer with a black sharpie, assembled the axle and then pulled out the axle just enough to see if the axle seal has wiped the sharpie in approx. the mid point of the retainer. Measure yours 1st for reference- as you did! Tricky, but once you understand the relationship it all makes good sense. Will report back , off to the shop now@@GarageBuiltHondas
@leestephens6983
@leestephens6983 Год назад
great work ,great filming
@jamestennimon9974
@jamestennimon9974 Год назад
This was a well done video
@Toyotatech86
@Toyotatech86 4 месяца назад
Damn it I wanted to see you clean the shaft…
@GarageBuiltHondas
@GarageBuiltHondas 3 месяца назад
I only do that in the shower generally. Lol
@sheerwillsurvival2064
@sheerwillsurvival2064 5 месяцев назад
I can’t believe that company didn’t make that tool to fit standard 20ton press . I won’t buy that one 😱
@GarageBuiltHondas
@GarageBuiltHondas 5 месяцев назад
Same. It works though. I haven't had one issue with the press either
@aperson9430
@aperson9430 6 месяцев назад
1.5 inch diameter 1 and 3quarters socket
@barbarawhite6601
@barbarawhite6601 7 месяцев назад
Perhaps you can help. I have a 2002 Tundra and the local Toyota dealer placed all of the new bearing components as you have. Yet, when I placed the axel, there was about a 4mm gap between the hub and axel flange. It would not seat completely. I tightened the four retaining nuts and drew the axel in, I sensed that the bearing was moved and seated deeper. But would that have created a gap under the C clip? Do you know what could have happened? Everything else seems appropriate. Dennis
@barbarawhite6601
@barbarawhite6601 7 месяцев назад
I came upon a Toyota dealer with a very experienced master mechanic. "Rob" has done at least 50 of these axel bearing installs. Turns out that when the bearing is pressed fully seated to the axle, it is not fully seated into the hub. It tends to be about 4mm proud. When the axle is inserted into the housing, it is then about 4mm of a complete seat against the axle housing flange. Tightening the four retainer nuts will draw in the hub. During this time, the bearing is not moving in relation to the axle, the bearing is fully seating into the hub. This is all normal and to be anticipated. Dennis
@carlito3094
@carlito3094 Год назад
Awesome video bro … thanks a lot
@thinshavings
@thinshavings 8 месяцев назад
You bought the wrong press tools. There is a guy on eBay in the USA that makes an awesome set that fits the press you have without cutting up the press. I have them they work great.
@GarageBuiltHondas
@GarageBuiltHondas 8 месяцев назад
Thanks, good to know! I don't mind, cutting the press has made it far more useful than it ever was before.
@jdmDC2ftw
@jdmDC2ftw Год назад
Toyotas prob have the best trucks but some repairs are a pain.
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Luckily this one went smoothly. Learned a lot along the way and glad to have this one in my bag now.
@swifty2aktive147
@swifty2aktive147 Год назад
😂😂
@danilolanzas1
@danilolanzas1 5 месяцев назад
Hi! Question. I’m trying to buy the bearings and other components but I’m having trouble finding them. Wish auto parts did you get them from? Thanks for sharing
@diltzm
@diltzm 2 месяца назад
Rock Auto ftw
@bobbouchee1452
@bobbouchee1452 Год назад
man i thought it was going to be like the colorado and had to tear apart the rear differential lol
@josephroy4132
@josephroy4132 Год назад
Thank u..good video!!
@dc7865
@dc7865 Год назад
Ma i distanziali non vanno messi a caldo? Sono entrati troppo facilmente 🤔
@corporalkang-in-chan7926
@corporalkang-in-chan7926 Год назад
Can these two special tools be used on Hilux vigo and Hilux revo ? i want to order
@GarageBuiltHondas
@GarageBuiltHondas Год назад
What year truck?
@corporalkang-in-chan7926
@corporalkang-in-chan7926 Год назад
@@GarageBuiltHondas hilux vigo 2014 for sale in Thailand
@onesri6108
@onesri6108 Год назад
I am too lazy to look. Do you have front wheels bearing replacement for 2002 Toyota Tundra?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I do not yet.
@sefofatai6618
@sefofatai6618 5 месяцев назад
Where can I get the exact same press? thank you
@GarageBuiltHondas
@GarageBuiltHondas 5 месяцев назад
Harbor Freight
@victorduran3910
@victorduran3910 5 месяцев назад
Can u tell me where u bought the pipe at . Thanks
@GarageBuiltHondas
@GarageBuiltHondas 5 месяцев назад
Ace Hardware
@Nick-wr7vv
@Nick-wr7vv Год назад
I should probably do mine. 20 year old truck. Probably about time. Are they good bearings?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I've had zero issues thus far. Maybe 1500 miles and also towed my car on the trailer 150 miles roundtrip in there. Still perfectly fine and no odd noise or vibration.
@Nick-wr7vv
@Nick-wr7vv Год назад
@@GarageBuiltHondas that's good. I enjoy working on cars. But sometimes my friends and family take advantage of me and just expect me to righty tighty and Lefty loosey their hunk of junks too. Oh well
@Baebon6259
@Baebon6259 Год назад
stick with OEM. My Sequoia OEM bearing lasted me 16 years and 300k miles before the humming noise.
@panchoflores6590
@panchoflores6590 Год назад
Hi sir to replace the thicker seal didn't see that good how you put it in? Do you need the press to install the rubber seal I replaced the bearings like two years ago but something started leaking hope is not the thicker
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I installed everything as I did in this video.
@panchoflores6590
@panchoflores6590 Год назад
@Garage Built Hondas thank you I did mine today one side again tundras are the worse the plastic cover on the bearing came off like nothing these are ball bearings inside instead of the bullet style bearings that's the reason there is so much play on wheels. Good luck with yours mine started leaking grease and oil on one side and only oil on the other. Hope you get many years out of your. Take care!
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Thanks for the input! I hope I do get some good mileage out of them
@spencerpoindexter6461
@spencerpoindexter6461 Год назад
Where can I get one of them things to slide over the shaft?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
The bar? Most local home improvement stores should have it.
@nmarkose
@nmarkose Год назад
Hey bro I’ve always wondered why you haven’t K swapped one of your EFs. Is there a chance you ever doing that in the future? That would be dope content for the channel.
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I haven't had the time/money so far. I'd like to build an EG K coupe for a track build but that could be quite a while. It's a plan I'd like to get to but my time working outside is a lot less now than it used to be so I move a lot slower these days.
@nmarkose
@nmarkose Год назад
All good bro. I’m in the early stages of swapping a K24a2 into my 88 hatch. I just scored the engine yesterday from a wrecked 04 tsx at a junkyard. It’s going to be a long process but I’ll get it done eventually. I’ll stay tuned in the meantime.
@raz_r_yaj8869
@raz_r_yaj8869 2 месяца назад
How are those amazon parts holding up?
@GarageBuiltHondas
@GarageBuiltHondas 2 месяца назад
No issues so far!
@garybrady7245
@garybrady7245 Год назад
What rims are you running bud? Are they Rock Trix? Just wondering I like them and wanting to get some new rims for my 00. Great video dude
@GarageBuiltHondas
@GarageBuiltHondas Год назад
These are Kansei Roku 17x8.5 +0. Wanna buy em? I actually just bought some new wheels last weekend.
@garybrady7245
@garybrady7245 Год назад
Can you maybe send me a couple more pics of them so I can see them a little bit better? I assume they'll fit my 00 regular cab lb? I'm completely stock. 6 lug but I might be interested for the right deal what new skates are you getting may I ask where is the place to buy rims
@letsride525
@letsride525 Год назад
Question, was there a speed sensor on the rear?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Negative
@ramseytrain
@ramseytrain Год назад
After all the time it took to take apart thae axles had rust pits where the seals run, so i ended up buying a dorman axle kit
@andreiwestlake5827
@andreiwestlake5827 11 месяцев назад
How do you like it? I don’t want to spend that much money but it would be better than doing this lol
@grinchblood507
@grinchblood507 Год назад
How many inches apart should the ball bearing sprocket be?
@grinchblood507
@grinchblood507 Год назад
Can you help me with that? I think they installed it wrong and the abs sensor is not doing the reading correctly, therefore the abs is on
@danthaman4778
@danthaman4778 11 месяцев назад
How many ton is the press
@GarageBuiltHondas
@GarageBuiltHondas 11 месяцев назад
20. I think the 12 would work just fine too. I used a 12 for years before finally upgrading to a 20 ton.
@ramseytrain
@ramseytrain Год назад
tou need a U hook crowbar
@circuitsevenautotech7488
@circuitsevenautotech7488 Год назад
Hey bud you said the pipe is 1.5 So is the pipe 1-1/4 or 1-1/2?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
1-1/2 or 1.5. A 1-1/4 pipe would be the 1.25 diameter. I bought mine at Ace Hardware just because it's like a mile from my house. I believe Lowe's and Home Depot have the piping also.
@circuitsevenautotech7488
@circuitsevenautotech7488 Год назад
@@GarageBuiltHondas thank you 🙏
@jeovanimunozcastillo4025
@jeovanimunozcastillo4025 Год назад
Hey i don’t know if your going to answer this but I I have a 1990 Honda Civic hatchback and want to know did you do the b series swap on the ef or did some one do it for you cause I want to replace the d series one and also was wondering how long did it take you to make everything fit
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I do all my work. It doesn't take me long, couldn't give you a time frame, but I have a ton of experience doing swaps so I'm quick and know everything that needs to be done for a B swap
@scooterman1965
@scooterman1965 Год назад
Does this work on the 2000 Toyota Tundra?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Yes
@scooterman1965
@scooterman1965 Год назад
@@GarageBuiltHondas Thanks, the top part said 2000 - 2006, but below it, it said 2001 - 2006. Thanks for clarifying that. Great video.
@jorgecardona4901
@jorgecardona4901 Год назад
My local Toyota dealer in Punta Gorda Fl quoted me $4500 to do. Both rear bearings 😮😢
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Yup, tough. I said "nah" also. Learned it myself and wasn't a hard job at all.
@mrantone916
@mrantone916 Год назад
Can you rent that tool ?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
I couldn't find one for rent when looking.
@bryin99
@bryin99 Год назад
Heads up! If anyone is doing this job on a 2001-2007 Toyota Sequoia is will be more related to this procedure. It will be just a little bit different. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-0DEeNLbFuRc.html
@trevorhenry1003
@trevorhenry1003 Год назад
What's the bearing part number?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
There's a link in the description.
@shadowbuilt915
@shadowbuilt915 Год назад
I need to do this to mine also. Mine is so bad it clunks on turns 😮. Can I rent the tool from you ?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Of course. Just let me know when you want to use it. We could probably knock out the job here at my house one of these days. I'm a pro at it now. Lol
@shadowbuilt915
@shadowbuilt915 Год назад
@@GarageBuiltHondas I’m down ! I think mine might need at least one new axle because it’s been like that for a while. I’ll price up all the parts soon and we can go from there. Thank you !
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Let me know!
@jasonsaldana8377
@jasonsaldana8377 Год назад
Are you in Austin?
@GarageBuiltHondas
@GarageBuiltHondas Год назад
El Paso
@jasonsaldana8377
@jasonsaldana8377 Год назад
@@GarageBuiltHondas Right on. That would be quite the drive for me to borrow that tool. 🤣 Nice video though, this is going to help me a lot.
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Right! 9 hours isn't worth it.
@gregmccarter2176
@gregmccarter2176 Год назад
They want $1,600 at dealership. Way over priced
@getdirecti0ns
@getdirecti0ns Год назад
1600 per side or for both?
@raulbueno4284
@raulbueno4284 Год назад
I bought those wheel bearings and they suck ass
@GarageBuiltHondas
@GarageBuiltHondas Год назад
Elaborate?
@raulbueno4284
@raulbueno4284 Год назад
I had those for a year and a half and they suck ass. That’s why I went back to. Oem
@GarageBuiltHondas
@GarageBuiltHondas Год назад
They wore out?
@azizb.7561
@azizb.7561 Год назад
No, they suck ass.
Далее
TOYOTA BALERO RETENES LLANTA TRASERA proceso completo
26:51