2002 - 2006 Honda CRV Backup Camera Install

Подписаться 129 тыс.

Просмотров 60 тыс.

50% 1

Parts used listed in the description below!
Watch a full tutorial as a 2004 Honda CRV will have a new backup camera installed to an aftermarket radio installed previously. This camera provides additional safety and visibility when reversing.
This video applies to Honda CRV models for years 2002, 2003, 2004, 2005 and 2006. This video also includes camera wiring, radio removal, installation, and testing.
Click here to see a helpful backup camera tutorial video:
• Car Backup Cameras Exp...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Backup camera used in this video (Amazon Associate Paid Links):
*License Plate Camera Kit: amzn.to/3wgX9az
Radio install Parts Used (Amazon Associate Paid Links):
*Dual DCPA701 Double Din Radio: amzn.to/3jzm2cF
*Metra 95-7801 Dash Kit: amzn.to/3Er3fJP
*Metra 70-1721 Wiring Harness Adapter: amzn.to/3gJNFid
--If you have steering wheel volume controls, use this harness adapter instead Crux SWRHN-62D: amzn.to/3h2pTNg
*USB Flush Mount Adapter: amzn.to/3gGHkms
Disclosure: As an Amazon Associate I earn from qualifying purchases

Авто/Мото

Опубликовано:

18 апр 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 54

@ProvoBeastAudio 2 года назад

Parts used linked in the description of the video!

@21boxhead Год назад

USELESS VIDEO WHY WOULD FISH THE WIRE TO LEFT REVERSE LIGHT WHEN IT COULD BE DONE ON THE RIGHT SIDE AND WHY WOULD SOLDER WIRES PASSED THE RUBBER GARMENT THE BACK SIDE OF TAILLIGHTS ARE NOT WATERPROOF AND WHY WOULD RUN THE WIRE UNDER THE GAS PEDAL? AND LAST WHY DIDN'T YOU SHOW VIDEO FEED INSTEAD OF "NO VIDEO SIGNAL" ? YOU TRYING TO SHOW EVERYONE YOUR A LAZY FAILURE?

@EZephyr5 26 дней назад

Provo, this video was very helpful to me. The top three things in it that were useful to me: (1) tapping the green wire with black stripe (love the specificity so I didn't need to guess!) to tell the head unit that the car was in reverse, (2) that the rear hatch panel could be unsnapped from its frame after removing a single screw, (3) the suggestion to use the auxiliary power outlet to supply juice to the camera. One thing I discovered that wasn't mentioned here is that the rear seats are can be leaned forward and perhaps even removed to ease of running the video cable in the door sills without removing the sills or carpet. I started my work at the head unit and I ran the video cable on the driver side to the back of the CRV because I found it easier to fish the video cable from the head unit into the driver's foot-well rather than trying to get the cable fished into the front passenger foot-well.

@FAroundAndFindOut420 Год назад

You know there a light on the other side that has all that and is closer. Would mean running less wire which is always a good thing

@zahari_s_stoyanov 9 месяцев назад

He had to extend the main power anyway to tap into the socket on the left

@alexanderpapii4866 Месяц назад

@@zahari_s_stoyanovHe could’ve used the black power wire on the reverse light bulb🤷🏻‍♂️ as power that what I did but all on the right side

@zahari_s_stoyanov Месяц назад

@@alexanderpapii4866 these systems require two power sources - one constant and one when the car is running. So the constant one is in the socket on the left

@inegma29 11 месяцев назад

Use posilock wire taps. Easiest and extremely well made design. They also are reusable, or if you mess up can be removed and used again. I use posilock connectors on everything.

@alexanderpetkov7848 Месяц назад

Link for those connectors?

@tryhard_david5656 2 года назад

thanks, this video was really helpful 👍

@21boxhead Год назад

don't do what he did it's unnecessary to run wire to left side tail light and cut the rubber gasket that's dumb

@keithgaxiola562 Год назад

@@21boxhead what are you supposed to do?

@21boxhead Год назад

@@keithgaxiola562 BEFORE INSTALLING THE LIGHT INSERT THE GASKET FROM THE FRONT OF THE LIGHT THEN PUSH IT BACK

@Jovis8888 2 месяца назад

So useful having searched for the colour coding of the positive side of the reversing light. Do you have a video of removing enough of the ceiling panel to access the antenna? I need to fit a DAB one.

@Fuzer831 Год назад

Can you add link of the stereo unit you used in the details of this video and also add the link to the video of the unit installed

@arvinanat9769 20 дней назад

I'm completely a newb. do you have links or types of wires you used to extend the trigger wire and accessory power wire? Thanks.

@rich-nn9on Месяц назад

As would be done in a 2002 CRV since it does not have a stock screen, it does come with a cassette radio

@warrenb9343 Год назад

I can not get the screws out that hole the upper-side cargo hooks on the side panels. I tried both sides, they just spin. I was able to get the camera wire through the gromet and into the cargo area. There's no way to get to those backup light wires without pulling that panel out more. Without getting those upper hook screws out it does not pull away enough. Any ideas where I can tap into the reverse lights? 2006 CRV. Thanks.

@inegma29 11 месяцев назад

Same with me. I finally got the screw out only to find out that those specific location hooks do not screw into the metal body of the car .....they are floating and only screw into the plastic panel no need to remove them.

@EZephyr5 26 дней назад

There is no need to remove these cargo hooks. They do not hold the panel in place against the metal frame of the vehicle.

@ducvu3265 2 года назад

Do you have to go to the driver side to access the backup light power? Thanks!

@Gagy260 2 года назад

You should be able to connect it to the passenger side.

@nololol Год назад

Did you ever get an answer on this? I really don't want to run it across from my driver side seems like a waste of effort

@stephenclark678 Год назад

The license plate on these CRVs is off center. Do the backup camera guide lines still work okay with the camera off center?

@21boxhead Год назад

nope he's a noob he also could tap into the tail light trigger from the inside without ripping the rubber gasket

@21boxhead Год назад

@@stephenclark678 center it mount it with screws to the plastic bezel on the rear door

@dankostine5974 6 месяцев назад

I bought one similar to this and I hooked everything up the way you did in the video, I’m not getting any camera feed but it does know when the car is in reverse, the leds around the camera are on too. Does anyone know how to fix this?

@John.Winchester 5 месяцев назад

sounds more like a issue with the camera not the installation

@mydearriley 4 месяца назад

How does the reverse camera come up on the dash if it's powered with the ignition?

@ProvoBeastAudio 4 месяца назад

Because power the camera off of accessory is separate than triggering the radio to go into reverse. Radio's that are compatible with reverse cameras will have a reverse trigger wire that needs to see 12v when in reverse, outside of power that camera. So you may need to run a separate reverse trigger wire if you are powering your camera on accessory.

@mydearriley 4 месяца назад

So, without the reverse wire properly wired, the camera could still be powered and visible, but just wont pop up when the car is put into reverse?@@ProvoBeastAudio

@ProvoBeastAudio 4 месяца назад

If you alternatively wire the camera on just reverse light power, yes, it will only function in reverse and receive power only when the reverse light is on.@@mydearriley

@mydearriley 4 месяца назад

Ah! I was thinking that the "trigger" wire = "powers the camera once triggered." But it's more likely a change in amps (or would that be a change in volts?) @@ProvoBeastAudio

@mydearriley 4 месяца назад

@@ProvoBeastAudio So, I have it all installed (following your guide, thank you), but the head unit is stuck with a black screen with green "No Signal" text. This happens as soon as I power on the car. However, when I put the car into reverse, the camera engages as expected. But once back out of R, it returns to the blank screen. I also have no speaker output (phone connects, but doesn't provide volume). Any ideas?

@rich-nn9on Месяц назад

Why did he go to the left side instead of continuing on the right side?

@ptmoy1 Год назад

The license-plate mount on the CRV is located off-center. Are the lines the camera shows for judging distances still accurate when the camera's mounted off-center?

@21boxhead Год назад

just center it mount it with screws on plastic bezel on the rear door

@robfinch6202 11 месяцев назад

@@21boxheadPost a video of how you did it .

@GeorgeWPush Год назад

Why did you use the left brake light instead of the right?

@ProvoBeastAudio Год назад

Well, we went to the reverse light, not the brake light. We went to the driver side for better access for recording video. You are welcome to tap into either side.

@GeorgeWPush Год назад

@@ProvoBeastAudio I meant reverse, sorry. How does connecting it to the left side give you better access?

@ProvoBeastAudio Год назад

@@GeorgeWPush For filming, not necessarily for access generally. Easier to show how to remove the rear light with the camera to show what wiring to tap into.