2007-2012 Ford Fusion/ 2003-2007 Mazda 6 Control Arm Replacement.

Подписаться 166 тыс.

Просмотров 33 тыс.

50% 1

In this video I show you how to replace a front control arm and press the control arm sleeve back in on your 2007-2012 Ford Fusion or 2003-2007 Mazda 6. It is a very basic DIY kind of job requiring no special tools. With that said here is the part and some things that will make your life easier while doing this job:
Control arm: amzn.to/2pqXV34
Torch kit: amzn.to/2pl70ea
Air hammer: amzn.to/2FSXaXw
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user Repair Geek makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. Repair Geek shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by Repair Geek and therefore, Repair Geek does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge Repair Geek or anyone affiliated with Repair Geek, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

Авто/Мото

Опубликовано:

3 сен 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 44

@andrewholmblad4866 6 лет назад

Great video ty for sharing. Another trick that may help in the future that many people don't know/forget about is using COLD instead of heat... Putting that sleeve in the freezer for a few hours can shrink it enough (even a fraction of a millimeter helps lots) to get that thing pressed back in.... Also bushings work even better in the freezer since they're not metal they shrink more.

@86CJ74U2NV 5 лет назад

This is one of the hardest ball joints I have ever had to take out of a knuckle. To get the sleeve back in, stick it in the freezer. I used a 5/8 grade 8 three inch bolt and washers to "pull" the sleeve into place. Worked like a charm.

@jeffersonluke4774 2 года назад

I realize it is kinda randomly asking but does anyone know a good website to watch new series online?

@jacksoncayson9242 2 года назад

@Jefferson Luke Flixportal :)

@jeffersonluke4774 2 года назад

@Jackson Cayson thanks, I went there and it seems like a nice service :) I appreciate it !

@jacksoncayson9242 2 года назад

@Jefferson Luke happy to help =)

@jamesallion7648 6 лет назад

Separate the ball joint with a pickle fork and you won't have to mess with that bushing! Place a floor jack under the ball joint nut after loosening, put most of the car's weight on the ball joint and wail away on the pickle fork. several good whacks is all that's needed. Nice video BTW!

@86CJ74U2NV 5 лет назад

I live in the rust belt and the only way to get it out was with the sleeve attached. I had to use a hydraulic press and heat to get the ball joint out of the sleeve.

@sarahb2159 6 лет назад

Thanks for the video, this will help make the work on my wife’s car go easier! It’s nice to see the job done before going into it myself.

@chesneyman 6 лет назад

Good video. I'll most likely be doing this on my Mazda 6 soon. Very harsh when hitting bumps and bushings are cracked.

@delin54 6 лет назад

I just did the job on a 2011, did not mess with the suspension as the inside bolt was easy to remove.

@tonycervantes4816 2 года назад

Good job bro.

@mauricemason482 6 лет назад

good video..i think i could do this ,ill watch again to be sure ive got it ..

@hoosiered471 3 года назад

Informative video for my exact car. Thanks!!! Thanks Ford for ditching all your cars (except Mustang), not everyone wants to drive an F150 everywhere. Never will understand their reasoning behind that move. The Fusion (with some updates/refresh) could easily compete with the Honda Accord/Toyota Camry.

@renenunez4015 4 года назад

Very nice video tanks

@gustavomelendez3477 6 лет назад

congratulation, thank you!

@celiadominguez8209 5 лет назад

hello i have to change both sides back and forth for my 2007 fusion ford! the question is Lateral Link Control Arm is the same, thank you

@jamesrichardson771 2 года назад

Thanks buddy 💥

@onlycodered 3 года назад

I spent a couple days trying to get those damn ball joints out of the steering knuckles. Ended up pulling the entire steering knuckle assemblies out with the lower control arms attached and installed my new control arms on a couple knuckles I got from my local junkyard for $50/piece. Well worth $100 to not have to continue hammering on those ball joints. LOL

@danielguzman8346 3 года назад

I have a question. I replaced the same lower control arm. The old one was really bad (ball joint). Didn't have a problem with the steering at all. I installed the new part and the car pulls or steering pulls to the right. The steering is not where it was before .my mechanic told that I need an alignment. Any ide why?

@atxjax1 5 лет назад

Driver side? On the V6 do you have to lift the engine up to get the subframe bolt out from the rear center arm?

@RepairGeek 5 лет назад

Yes.

@lbeezy7215 5 лет назад

Before tightin nuts preload tha spring to 15 7/8

@anthonybrett7 4 года назад

He said he wasn't going to torque the bolts until he had weight on the wheel, he even went into good description of why its a bad idea not to preload the spring before tightening the bolts, 15:00. He only snugged the bolts down first.

@larryhernandez769 2 года назад

Can a 2007 Mazda 6 rear l Lateral arms interchangeable with AWD 3.5L Fusion sport rear Lateral arms ? Does anyone know? Stay Frosty All 🥶

@drewgregg4952 Год назад

Are all the subframes the same as well I have a 06 Mazda 6 3.0 Automatic duel Manuel 4 Dr Sedan and I can’t find one so can anyone help me with rechargeable crossmember subframes PLEASE

@realjiver2 3 года назад

You can get replacement boots for a fraction of what the arm costs.

@djockeydublin1225 4 года назад

Does this not apply to the 2008 Mazda 6?

@anthonybrett7 4 года назад

The setup looks the same in my Mazda 6 mark 1, body type GG

@gratefulaya192 6 лет назад

you could have lowered the sub-frame to get that rear control arm bolt out, it's pretty easy to do.

@Pinkielover 3 года назад

6:00 never grip it on the sleeve .. just press it out

@Mike-we3rb 3 года назад

“Not that hard for doing on jack stands” me hearing that after watching another video of someone needing to lift the trans and lower subframe to remove the lower arms bolts

@mtsanchez27 3 года назад

It's needed for the driver side my brother

@Mike-we3rb 3 года назад

@@mtsanchez27 yeah

@inyoudeep1 4 года назад

My only real issue is that you only changed one! You should have changed all four! No self respecting Tech would only change one.

@RepairGeek 4 года назад

Yep only changed what was broke, instead of ripping someone off for all 4 😂 and that's apparently a bad thing?

@inyoudeep1 4 года назад

@@RepairGeek No, it is called saving the customer money, and their lives! Part changer like you are why Techs get sued! You should be lock in prison for ripping people off! It is much cheaper to do the job right the first time and not have them pay it again over and over again, because you are too stupid to understand how reality works!!!

@inyoudeep1 4 года назад

@@RepairGeek Only changing one, knowing full well that all four need changed, as it is always known, is ripping someone off! You are a scammer and the reason people think poorly of techs.

@RepairGeek 4 года назад

@@inyoudeep1 cool. Next time I get a car in for a brake job I'll change the master cylinder and all the lines as well. Then, tell the customer I'm doing them a favor by changing everything. Makes total sense.

@inyoudeep1 4 года назад

@@RepairGeek Changing only one, is like only changing one brake pad! You know it, but are trying to justify ripping people off and endangering their lives.