2006-2012 Ford Fusion Lower Control Arm Removal Without Dropping Subframe!

Подписаться 848 тыс.

Просмотров 58 тыс.

50% 1

Moog is the only aftermarket I trust for Suspension and Driveline:
I used the R Series linked below (check fitment guide)
Front Lower Arms-
www.amazon.com/gp/product/B007...
Drivers Front Rearward Arm-
www.amazon.com/gp/product/B007...
Passenger Front Rearward Arm-
www.amazon.com/gp/product/B007...
Help the Tour along by donating below:
GoFundMe Here- www.gofundme.com/FordTechMakuloco
Paypal Donations Here- www.paypal.com/cgi-bin/webscr...
Tour supporters include:
AJ1E Superior Solutions-
www.fordservoboretransmissionf...
Hot Shot's Secret-
www.hotshotsecret.com/
Car Part Kings-
www.carpartkings.com/
Milwaukee Tools-
www.milwaukeetool.com/
In this video we tackle lower control arms on a 2007 Ford Fusion with a few tips along the way for removing them.

Авто/Мото

Опубликовано:

6 июл 2015

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 79

@arisaka9963 6 месяцев назад

Worked just as you said it would. Thank you sir!

@jmplants 9 лет назад

Got the popcorn ready bring on those videos

@Low1246 9 лет назад

Great Vids man! Keep it up!!!

@orfeous 9 лет назад

That was a big nice garage to work in! Cant complain about that :)

@MyPuppers 9 лет назад

great job !

@SISI0887 9 лет назад

Awesome as always!

@mikecont9742 5 лет назад

Great tip. Very informative..

@mds19238 9 лет назад

Used to having hydraulic lifts to work on cars, I was in for a shock after I retired...dirt, concrete and asphalt are hard on the knees and the back. I accidentally found that the benefits of large card-board boxes (still using the same box my compressor came in two years ago) have made many a shade-tree repair much more bearable. Save your knees. Good luck.

@FordTechMakuloco 9 лет назад

mds19238 I have something very similar we used to use cardboard creepers even at the dealership real nice to have.

@utahbones3094 9 лет назад

Great Job!

@pjleash 5 лет назад

Great video. The tip on the sub frame for the rear lower arm will definitely come in handy. I'm fighting those lower ball joints, though. It's killing me .. .

@alb12345672 9 лет назад

The forked shock reminds me of the 95 thunderbird suspension I redid. Most of the bolts were frozen in the sleeves. I couldn't locate a new shock bolt (wasn't sure about the size) so I suffered almost an entire day getting it out in one piece. Since there is a rubber bushing you can't really cook it too much.

@chrischickcowski3477 Год назад

Good tip to this day!

@rusco321 9 лет назад

You gotta get a foam pad for your knees to rest on, cause that concrete/asphalt gets old real quick.

@FordTechMakuloco 9 лет назад

I enjoy it actually something about it

@jsjizza1540 9 лет назад

Love the videos keepem coming !!! I will keep my 05 Explorer as your videos continue!!!!!!

@slideman. 8 лет назад

FordTechMakuloco - It would greatly appreciated if you could show some of the other work on this V6 Fusion. I'd like to see the valve covers gaskets done, if at all possible. If you could post more videos from this job it would be great!

@FordTechMakuloco 8 лет назад

+sailmate If it comes in I shall film it.

@bash5995 9 лет назад

My wife had a 2013 ford fusion with 38,000 miles on it and both lower control arms were wore completely out to the point it would make metal on metal contact clanking sound every time you hit the brakes or went over a bump. We took it to the Ford dealership where we bought it and they said it was perfectly normal for the front suspension to wear completely out in less than 40k miles. They said they would fix it for $1000, we just traded it in at another Ford dealership because we had multiple other problems since it was new. I still love your videos though!

@eldoradony 9 лет назад

bash5995 Considering the age of your car and the mileage The dealership did the wrong thing with you and consequently lost a customer. I had some issues with my 2010 Malibu after the warranty expired with parts that should not have been issues. My dealership went to bat for me with GM and twice the issues were corrected at a cost of $200 to me and a retail repair invoice cost of $600 and $900 respectively. I think that was very fair and when the time comes to buy I will go back if its a Chevy that I want.

@jacobroyer4706 2 месяца назад

I have a 2010 with all original suspension components and 306k I am about to do this job on.. never had a single issue with any of our fusions wearing this stuff out until now I can’t. Complain

@automaintenancesupplyalfon7022 9 лет назад

FordTechMakuloco I will keep you and your family in my prayers what your doing for families across America is a true blessing I know with all the driving, hotels and working hard can be very exhausting ! Stay strong God bless you and your family. .......

@cmarshall2211 9 лет назад

Rather short. Was expecting a more in depth video of the repair process like you used to do. Other than that, appreciate what you are doing.

@FordTechMakuloco 9 лет назад

cmarshall2211 This vehicle was such a nightmare we stopped filming it was that bad and time was ticking away. Other videos after this are more in depth I have a bunch uploading today.

@cmarshall2211 9 лет назад

Can't imagine the difficulties of filming in unfamiliar areas. Couple that with an unexpected difficult repair. Hopefully you got a lot of thanks and a cold beer when you were done!

@MrLiipasin 7 лет назад

Did you use jack under the subframe or not? I am doing this job soon on my mazda 6 gg/gy. Eveybody says to lower the subframe and i am very happy that i found your video. Seems that i can save a little time with this shortcut! Thanks!

@MrLiipasin 7 лет назад

And did you disconnect the steering column from the steering rack? Thanks

@ervinzefi8662 6 лет назад

How do you remove the upper bolt of the lower rear control arm. I did remove the nut with the washer that and the bolt has two grooves . I tried to wrench it out but it didn’t move. I wasn’t sure if you just hit it from the back and comes out or unbolt it. I’m talking about a 2006 mercury Milan

@moneygurl314 5 лет назад

That bolt your loosing on the control arm on the frame broke out of mines with pieces of the frame is there anything I can do to fix it besides changing the the sub frame?

@NissanPRO4X 9 лет назад

What convinced you RAM was the right truck for your road trip?

@countcrotchula92 7 лет назад

I have a 2012 Fusion.. what is the process for removing the lower forward arm?

@johnbosco2404 5 лет назад

DIY Uly drop the frame

@kennymaindenison2245 4 года назад

Well I see that tool didn't do very good at keeping that sleeve in like you said it was supposed to do.

@FordTechMakuloco 4 года назад

Yeah sometimes they get stuck big time, it's always a fight.

@kennymaindenison2245 4 года назад

@@FordTechMakuloco oh yeah, I just fought one awhile back that's why I was watching to see how that tool worked out. I just hate when I get them in the air and see they're from up North. Dam rust buckets !!!

@yoxvan17 7 лет назад

Where can I purchased the clamp or tool that your using to remove the control arm

@jasonpanus8246 7 лет назад

im looking for the same tool????

@mark8lifestyle322 5 лет назад

FordTechMakuloco, Aren't the bolts torque to yield from the control arms to the subframe?

@michaelperkins1878 9 лет назад

I notice at 5:09 you show a photo of a Duratech V6 with the timing chain cover off. I am trying to remove the front cylinder head on mine... preferably without dropping the engine. Can this be done? And how did you get the timing chain cover off without removing the engine?

@FordTechMakuloco 9 лет назад

+Michael Perkins This is a very bog job and should be attempted without full instructions from a chiltons manual or such. The heads can come off without pulling the engine.

@michaelperkins1878 9 лет назад

I am planning on pulling the half shafts and the rear drive shaft (AWD) and the jacking up the engine in the car to get to the timing chain cover. It appears that this is how you did it.

@michaelperkins1878 8 лет назад

+FordTechMakuloco I have a chiltons manual and it is tell me to drop the subframe and engine. however, there are no instructions to pulling the heads and timing chain cover without dropping the engine.

@Viages 9 лет назад

Which truck you find better , the ram or the F150? ,, in terms of power reliability etc etc ?

@TeeKeepGoing 7 лет назад

Do you travel to Wisconsin? Small college town.. I have a 2010 Ford Fusion that's making loud noise every time i turn the wheel or go over a bump. I'm scared to drive it now.

@dylanarnsdorff5947 5 лет назад

I could not for the life of me get the subframe to move enough, but I did manage to get the screw out, im just wondering how I get it back in. Also had a ceased ball joint that I hope a shop can press out. Its amazing how you try to fix one thing only to have to destory alot of things in the process.

@dylanarnsdorff5947 5 лет назад

Ended up taking the steering off, but still didn't lower even with prying

@dylanarnsdorff5947 5 лет назад

It appears the sub frame is somehow welded or rusted to the frame as the drivers side there is space between the frame and subframe, but the passenger side there is no space. The bushing moves when I pry it, but not that far.

@robduston8138 Год назад

Can’t get my subframe to move either

@fishermenmike47 6 лет назад

Good job,if you own a ford to those who have one,you better learn mechanics,coz its gonna be a costly one,

@atxjax1 5 лет назад

Does the lower center arm rearward bolt come out easy on the V6 or do you have to lift the engine just like the 4Cyl?

@franklinmorales78 7 лет назад

Do you recommend the MOOG parts? On the internet there are many critics concerning the low quality and I personally broke a inner tie rod moog with just 25 thousand miles .... I need to change the upper control arm a Ford Fusion 2008 and I am seeing which brand to use .....

@gdtrfb81 7 лет назад

Hey, quick question. I'm having trouble getting the rear lower control arm nut bolt out. It is basically seized into the control arm. What do you recommend in getting the bolt to come loose? Basically soaked it in pb blaster, tried an impact gun & breaker bar. Anything else?

@ChicagoMillingCo. Год назад

heat

@silverfox401 9 лет назад

You drive a Dodge truck instead of a Ford F1 50?

@FordTechMakuloco 9 лет назад

Yes please keep up lol

@adamwade9065 3 года назад

Did you record how you got the timing off??

@carslover3509 9 лет назад

you are smart man

@FordTechMakuloco 9 лет назад

amjad amj Thanks! I am smart enough.

@TheSimpleObserver 9 лет назад

That looks a lot easier than a 2005 Toyota Camry! Just about 4-5 hours per side on a Toyota. You need to pull motor mount and raise engine on a Toyota to get to the bolts. I wish you had chose a Ford over the Fiat G.M. truck. :(

@bigdaddymak1439 9 лет назад

Driving a Dodge Ram to go fix Fords! Priceless!! LOL

@franklinmorales78 7 лет назад

In 5:10 what work do you do?

@richvas3214 7 лет назад

is it free i have the same car need both fixed upstate ny

@JimAbbett 7 лет назад

I am following your instructions but the subframe is not dropping more than 1/4" or so. Any ideas?

@FordTechMakuloco 7 лет назад

It will only drop a 1/4" or so you need to pry it down with a prybar just enough to clear the bolt.

@JimAbbett 7 лет назад

+FordTechMakuloco I will give it a shot. Thanks!

@JimAbbett 7 лет назад

+FordTechMakuloco That worked! Thank you!

@stuartbear922 5 лет назад

Disconnecting the lower steering shaft is very easy. Not totally necessary, however. Remember to keep the steering wheel in place while disconnected. And, the steering shaft will not release until the bolt is fully REMOVED.

@pabloredevils 8 лет назад

I'm desperately needing help with my 06 ford fusion. I have a code P0757. I can't pay anybody to do the job now, I watched your video on the Focus changing the Solenoid A. My problem seems to be on B. Please any help please

@marks6072 9 лет назад

Ford seems to use some questionable manufacturing techniques on most of their cars except the F-150... I just bought a 2014 F150 and I hope I don't have to deal with some of these short-cut designs... Thanks for sharing

@plowtruckdriver 9 лет назад

Mark S good luck with your F150 i have a 2012 one and the A/C just sucks doesnt cool the crew cab off FORD says its normal remember the saying "quality is job one" not any more. now its"have you drain one lately" I really dont want to drive one now. . With the paint falling off my 2009 Taurus im bout done with Ford

@marks6072 9 лет назад

Couldn't wait for Honda's pickup.. It's still another year out..

@WizzRacing 9 лет назад

plowtruckdriver Really. As my AC cools down to 46 degrees and considering it's R134a I'll take it. As the only other AC I seen that blows colder is a Honda. They will spit ice cubes out the vent. Being that it's a conversion van, E-150 it can cool it down in five minutes. Just don't ever buy a black vehicle and expect it to stay cool in traffic. It's never going to happen.

@oldsguy49 3 года назад

Did you ever wonder why this whole setup is so complicated? Why not just have a simple 1 piece unit top and bottom.? I have done this 3 times to my fusion.

@FordTechMakuloco 3 года назад

Yes yes and yes!

@BallsMcVaultCock 2 года назад

A dodge....

@SilentServiceCode 9 лет назад

I watch your videos and am turned off by Ford more and more. My Hyundai Elantra is way more straightforward to do anything on than Ford these days... It's two bolts (not hitting subframes) and a balljoint like it should be

@FordTechMakuloco 9 лет назад

SilentServiceCode You have to remember no other Ford is like this and this is a Mazda design which the Fusion is heavily based off of.

@franklinmorales78 7 лет назад

Moog parts are bad review......... low quality parts.....