2010- 2021 Kia Sorento Water Pump Replacement

Подписаться 14 тыс.

Просмотров 33 тыс.

50% 1

Hey Everyone
In this video I show the process of replacing your water pump on your 2015 Kia Sorento.
The Process is the same from 2010 to 2021 but the belt routing is a little different on the 2010-2014 models.
Total time is 1 hour and 20 minutes. That is with the bleeding of the cooling system.
Hope you enjoy😄
Torque Specs
Wheel Nuts Torque- 100 ft/lbs
10mm bolts- 10 ft/lbs
12mm bolts- 20 ft/lbs
17mm nuts-61 Ft/Lbs
17mm Bolts-79 Ft/Lbs
Alan key -20 ft/lbs
If you would like a quality water pump at a fraction of the cost, use GATES.
Coolant - Green Long Life(Suggest getting from dealer)
Pressure Analysis Program Video link
• Pressure Analysis Pro...
Application is for sale-- at a price of (25$ CAD) ( 20$ USD) (15£)
. The funds generated will go to help grow the channel.
If interested please send payment to paypal.me/Jeremyletourneau. (If you do not see my Company LOGO do not send the payment.) please add a Valid Email Address in the notes section when sending payment.
*The FacebookPay is not yet available in Canada(I was not aware of this)
Thanks for everyone's continuing support.
Email:
JLsAutoSolution@gmail.com
Mailing address:
JL's Auto Solution
21blvd De Gualle Chateauguay Qc, J6K4c4
Disclaimer:
Always follow Correct lifting and safety Procedures.
The information provided within this Video
is for general informational purposes only.
While JL's Auto Solution tries to keep the information
up-to-date and correct, there are no
representations or warranties, expressed
or implied, about the completeness, accuracy,
reliability, suitability or availability with
respect to the information, products, services,
or related graphics contained in this Video for
any purpose. Any use of this information is
at your own risk.
0:00 Introduction
1:40 REMOVE THE SPLASH GUARD
3:04 PULL COUNTER CLOCKWISE AND REMOVE THE BELT
4:54 USE A JACK AND A BLOCK OF WOOD TO SUPPORT THE ENGINE
5:40 REMOVE THE WATER PUMP PULLEY
6:20 A LITTLE LOOSE NUT NEVER HURTS
7:43 INSTALL THE WATER PUMP AND MOUNTING BOLTS
9:01 INSTALL THE WATERPUMP PULLEY

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 58

@mfsperring 2 года назад

Great job with the editing production. Really ramping up your content creation. I really liked this method.

@JLsAutoSolution 2 года назад

Thanks so much!

@johnjackson3622 2 месяца назад

MAN I LOVE the detail that you put into your video

@JLsAutoSolution 2 месяца назад

I appreciate that!

@DistortedApricot Год назад

i gotta do this on my wifes sorento. i love to get an idea of whats necesary before hand. perfect video. thank you

@JLsAutoSolution Год назад

Glad it was helpful!

@denisouellet6290 6 дней назад

Perfect tutorial ! Nice editing! Many thanks!

@JLsAutoSolution 6 дней назад

Glad you liked it!

@jrendoso Год назад

Awesome video! Thank you for taking the time to do this.

@JLsAutoSolution Год назад

My pleasure!

@gregjones8501 2 года назад

Fastest water pump job I’ve seen in a while! Great video bro! Keep em coming!

@JLsAutoSolution 2 года назад

More to come!

@OneLegged-honda-mechanic 2 года назад

Very well made video!👍

@herculesworld4016 Год назад

Thank you for this. Great Job. Wife ‘19 sorento started smelling sweet so I checked under the hood. The pump is definitely leaking, but very little….

@JLsAutoSolution Год назад

Glad it helped

@Ccity85 11 месяцев назад

Mines doing the same

@tuggie7589 2 года назад

finally someone, that gets right to the point and knows what the hell he's doing. Cute too...

@He-reigns 8 месяцев назад

Excellent work great video!

@JLsAutoSolution 8 месяцев назад

Thank you very much!

@nickhicks7051 2 года назад

excellent information thank you

@JLsAutoSolution 2 года назад

Glad it was helpful!

@davidnaish6804 11 месяцев назад

Perfect timing. My pump just started to leak a bit. Thanks for the video. (Mind if I borrow your hoist?)

@jimweishuhn-lw7fq Год назад

What a great video

@JLsAutoSolution Год назад

Glad you enjoyed it

@mikemuzzell5167 8 месяцев назад

Thanks man

@JLsAutoSolution 8 месяцев назад

You're welcome!

@renediaz4164 2 года назад

My Kia Soul 2015 is leaking coolant right from that area of it. I just noticed it. I already had bought 3 gallons of coolant before. Is Kia Soul water pump in the same area like the Sorrento have them?

@e.s.l5861 7 месяцев назад

Awesome tutorial. Do you have the torque specs for the bolts?

@mulonru2965 Год назад

My 2017 at idling stays cool but when driving quickly overheats and turning on heater helps cool it back down while driving, yes radiator fans works fine

@JLsAutoSolution Год назад

check coolant level,/coolant leak/ or it could be stuck thermostat

@esprado690 Год назад

My 2106 sorrento started to get coolant coming out the reservoir. Changed the radiator cap and thermostat. Drove it with no issues for over 30mins and then temp crept up (same issue it had before) Fluid coming out the reservoir again. Think I burped the system well. Doesn’t seem to be leaking anywhere else. Fans on after I turn off the car - so not the fans.wanted to see if it could be something else before swapping a pump.

@JLsAutoSolution Год назад

I would check for a head gasket issue, before a water pump. going by what you are expalining.

@FrankMiller-ih7uq Год назад

How often have you seen an impeller coming loose on the water pump shaft? I currently have no heat at idle and good heat while driving. This is a 2016 Kia Sorento with 150,000 km

@JLsAutoSolution Год назад

that is not a pump issue, i would suspect a head gasket/low coolant/air stuck in system. a broken water pump will cause instant over heat issues.

@TWri-um8xc 3 месяца назад

What are the blue marks on the pulley? Do they have to be lined up with anything?

@JLsAutoSolution 2 месяца назад

No nothing at all

@gregdube9172 Год назад

Bought a water pump and it came with two felt gaskets. My question is the rubber o ring gasket that you replaced good enough or do you use the felt gasket as well over top of it?

@JLsAutoSolution Год назад

Only use gaskets that are supposed to go there, should be 3 gaskets in total to complete this job

@gregdube9172 Год назад

@@JLsAutoSolution ok , just when i removed the old water pump there was only the metal gasket and the rubber o ring gasket that came off

@iankelly2110 2 года назад

good job Jeremy. how are you settling into the new workshop

@JLsAutoSolution 2 года назад

It's going ok.. I think I am just tiered of all the dealership Bull****, they only care about $$$$$ and dont give a rats *** about the client. all dealers are the same.. Most techs at dealers are only there for the pay, Dealer ships are becoming parts cannon central. Got a code- change the part-- next. Even the Tech line changes parts until it doesn't fix the car, then they are like" well it must be something you did, Good Luck". My boss tried to get me to change the parts based on a dtc. I told him NO. That's not how I work and it goes against my personal morals. Any ways thanks for watching Ian.

@iankelly2110 2 года назад

@@JLsAutoSolution I understand what you are saying bud its money making scheme some great techs out there just let them work and do there diag not follow flow charts all the time . keep at it Jeremy you will have you're own shop some day

@BCxDiZatioN 2 месяца назад

To do the front cover do u have to take the water pump off ?

@JLsAutoSolution 2 месяца назад

yes it needs to be removed for timing cover repairs

@shakilahmed4003 2 года назад

Do I need to replace engine water pump of kia sorento 2012 at 150km? Currently no issue or leaking.

@JLsAutoSolution 2 года назад

If it's not leaking I would leave it. but they typically tend to fail around that mileage. Use a light to visually inspect the water pump, if there is not sign of leakage( corrosion or green crusty bits) then I would not replace it. Thanks for watching

@shakilahmed4003 2 года назад

@@JLsAutoSolution Thanks Mate. I will do that.

@kaylalynn8448 2 года назад

Hi, I have a 2011 Kia Sorento with the code P0880. It will put my car in limp mode and it will be stuck in 4th gear. It will mostly happen when I cold crank my car, but sometimes if I let my car heat up and run for around 15 minutes then cut the switch off then back on and it will run fine. It is also draining my battery, so if I put a new battery in it then it will work right for a couple days. I have got my grounds cleaned, checked relays, had a couple different people look at it. I know the transmission works fine because it will sometime drive fine. I have been told it’s the wiring in the transmission, it could be the shift solenoids in the transmission or a short wire anywhere in the car. It is very frustrating and I have been trying to solve this issue for over a month! Please help! Thank you!!!!

@JLsAutoSolution 2 года назад

the dtc that you are having is indicating that there is a power supply issue, this could be in any one component or wiring. Since your issue comes and goes the vehicle needs to be tested with the fault present.