2019 - 2023+ Chevy / GMC Truck Amp and Subs Install

Подписаться 126 тыс.

Просмотров 98 тыс.

50% 1

Parts linked in the description below!
Watch a full tutorial as a 2020 Chevy Silverado will have four new Skar Audio 8" subwoofers and Kicker 1800w RMS amplifier installed. We will also be using an AudioControl LC2i and Epicenter for our line out converter and signal EQ for our amplifier. These amp and subs will be integrated to the factory audio sound system.
Note: This vehicle was equipped with the Bose amplified system from the factory. We will be retain the Bose audio system fully, and this install only integrates into the factory subwoofer for signal. If you do not have Bose, you will need to obtain your signal from your rear door speaker channels or behind the factory radio.
This video applies to Chevy Silverado or GMC Sierra trucks for years 2019, 2020, 2021, 2022, 2023, and newer. This video also includes amp rack installation, wiring, and testing.
Non-Bose Chevy / GMC Truck Stereo wiring diagram (if not using the T-harness):
Front Left (+): Blue
Front Left (-): Brown / Blue
Front Right (+): Yellow
Front Right (-): Yellow / Black
Rear Left (+): Green
Rear Left (-): Green / Black
Rear Right (+): White
Rear Right (-): Blue / Black
If you have any questions, leave a comment below! Be sure to like and subscribe!
Parts Used (Amazon Associate / eBay Partner Paid Links):
*Skar Audio 4 Gauge OFC Wiring Kit: amzn.to/31f0r2U
*Skar Audio SDR 8" DVC 4 Ohm Subwoofer(s): amzn.to/42L1IbK
-Recommended amplifier for those subs: amzn.to/46EiWdP
*GM Truck Box for (4) 8" Subwoofers Ported: amzn.to/43wikVh
*AudioControl LC2iPro: amzn.to/42kWnYU
*AudioControl Epicenter: amzn.to/3Kp2zGw
*1' RCA Cable(s): amzn.to/44z1hmW
*Metra 9 Conductor Speaker Wire: amzn.to/3xK4PSk
*Rear Wall Amp Rack (non paid): soundsgoodstereo.com/products...
--If you are looking to add a MULTI-channel amplifier, or multiple amplifiers and want to totally BYPASS the factory Bose amplifier, you will need:
*Axxess AXDSPX-ETH1 DSP Bose amp bypass kit: amzn.to/3SwJsBe
*NOTE - If you DO NOT have the factory BOSE Audio system, you will not have a factory sub to tap into, instead, use this T harness at the radio to connect your speaker wire to your line out converter. This depends on the factory radio, refer to Pac to determine which harness is needed for your install:
*Pac LPHGM71 Radio T Harness: amzn.to/3Uk7GA9
OR
*Pac LPHGM72 Radio T Harness: amzn.to/49r2Y83
Disclosure: As an Amazon Associate / eBay Partner I earn from qualifying purchases

Авто/Мото

Опубликовано:

17 июл 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 233

@ProvoBeastAudio 10 месяцев назад

Parts used linked in the description of the video. Check it out!

@yuniordelacruz3628 18 дней назад

I have a 2023 gmc elevation non bose audio will that amp rack fit on my truck?

@victorreyes4971 27 дней назад

Option one: You would have to remove the seat every time you want to make quick or minor adjustments. Option two: leave the rear passengers without a comfortable back rest 😅

@fulanito47 10 месяцев назад

i love it! good job! very clean!!! I'm actually looking forward on buying this truck in the near future.. pretty much what i want to do also. props to sound good stereo for making that amp rack!🤩

@timothymedders7110 2 месяца назад

Just wanted to say thanks for posting this. I installed quad 8's in my 24 GMC SLT. It was easy with this excellent video.

@davidrendon9838 25 дней назад

Did you have a problem with remote unlocking doors and turn on the Amp? Like a couple of others have commented about?

@juliansdiamonds 6 месяцев назад

This job is absolutely 💯 beautiful !!!! Thank you for this !!!!

@19gkk1le5 9 месяцев назад

Huge thanks just picked up a 23

@ClemsonNigel 8 месяцев назад

Wow!!! This set up is so clean. I have a 2020 AT4 with the same Bose system so this video is exactly what I needed. Just wish SC was a little closer to Utah so you guys could do it lol

@ProvoBeastAudio 8 месяцев назад

Give it a go yourself! All parts we used are linked in the description.

@tosby1 5 месяцев назад

South Carolina? What's the name of the shop

@frubalcava2208 10 месяцев назад

Everything looks really nice 💯

@itz_andyt 4 месяца назад

Amazing job well organized 🔥🔥

@johnathanstarnes2149 3 месяца назад

Super clean great job

@gyfhj 6 месяцев назад

Great video Brother! 💪🏼

@19gkk1le5 9 месяцев назад

Crazy clean 👌

@aisensoto190 5 месяцев назад

Could you do a video on how you do the wiring with more detail and how you make it look that clean

@gumbeelee21 10 месяцев назад

Nice job!!!

@henrythompson5624 8 месяцев назад

Super clean setup I wish you guys can hook up mine

@jesusmelendez1054 2 месяца назад

Que ermoso travajo me encanto una chulada de jale viejon

@redsmith882010 4 месяца назад

Wish i would have seen this video on the amp rack, i did how ever order the same one recently. I also went with a T-harness from LLJ Customs that plugged into the bose amp and left pig tails for the LC2i. My problem how ever was finding the right size amp to fit behind the seat....if it's over 2.5" tall, the seatwon'tt fit. I was using the SFB2000 for almost 3 years before the cooling fan quit working.Took some time to find a new a new stronger amp but, found the DC Audio 3.5k that fit perfectly...with a luttle grinding of some plastic off the seat for extra clearance. Almost back in action.

@redsmith882010 4 месяца назад

My other issue was the mounting bolts for the rack....I had to counter sink all but 1 so there was room for the amp to sit. So, unfortunately I couldn't assemble everything outside of the truck...had to install the board then the equipment.

@davidrendon9838 29 дней назад

Good info on the amp height. Looks like the Skar equivalent 1500 is 2.25 height. Should fit.

@IPvFletch 3 месяца назад

did you have to trim rear seat back foam? or those foam surrounds which stick out along the sides? Thanks!

@thomasnew8606 10 месяцев назад

didnt show the actual subs or final look and sound???? The factory stereo can keep up with all of that sub power now?

@overtime0101pg 3 месяца назад

Thanks for this video. It's well thought out. Question: can I use a PAC SNI-15 Preamp Adapter, PAC SNI-50A Line out converter, and PAC SNI-35 Variable LOC Line out converter to achieve the same as your LC2i PRO 2-Channel Line Output? BTW, I don't have the Bose Amp/Speakers @ProvoBeastAudio

@engineered2 3 месяца назад

How much foam trimming did you do on the back of the seat?

@hitemup85 7 месяцев назад

I have a 2014 Cadillac CTS with Bose would I still need an Amp- pro or Navtv if I’m installing a Audiocontrol DM 810

@cjcallen5974 Месяц назад

are you able to pull your remote off of the bose amp wires if you are not using the lc2 in the video? and do you know which wire that would be?

@patjunick8965 2 месяца назад

How do you put all that stuff behind the seat with all its foam? I just took my seat out to try and fit two self contained 8 inch JVC subs and they don't fit. One would directly in the middle, but the two don't.

@johnamorrison82 5 месяцев назад

Awesome video! A lot of help for me while I'm installing my stereo. The only issue I had and I notice it for you too, the seat belt rubs the LC2i. Any ideas? I don't want to redo it all.

@ProvoBeastAudio 5 месяцев назад

For how often the seat belt won't be used, customer didn't care, and wanted it there.

@firefox0915 Месяц назад

Did you remove that factory foam pieces off the rear of the seat so everything had room?

@MrBamf00 4 месяца назад

I have a 2018 Silverado with Bose can I use those same blue and green wires to provide a signal for my LCI2?

@ljpsr 10 месяцев назад

Great video as usual!! I have a question. In a f150 I want to install a lc7i. Is there a harness in the back where I can pick up a signal without going up front to the radio? I'm also removing the pac ampro.

@ProvoBeastAudio 10 месяцев назад

Hey there, thanks! Amp Pro connects that the radio, along with any T-harness on the market. The only instance where a harness is available in the rear would be trims with the Sony / B&O audio system from Ford where you can add the bypass harness at the factory amp in the rear. So the answer is a "yes, but...". Depends on your trim.

@davidrendon9838 25 дней назад

I’m following this set up exactly. What size wires are the four 8’s using in the box? The wire kit you linked to use has 16 AWG. Is this correct to use?

@OEFVETERAN Месяц назад

Does the Bose amp still amplify the Bose speakers and the new amp the subwoofers only? Thanks! 🙏🏻

@GMCB-pu8pk 5 месяцев назад

How much does this set up cost with parts and labor? I want to do something similar in my truck

@yaboihuskymolly1159 2 месяца назад

What is the thing you moved all the way to the right of the amp board?

@Digital7C4 9 месяцев назад

Where did you set your AccuBass Level and Threshold and Output Level? I have the same truck and and LC2i Pro as well and will be finishing my install soon. Thanks!

@ProvoBeastAudio 9 месяцев назад

Honestly, since it wasn't a personal truck, I can't remember. The LC2i pro instructions have a guide on walking you through the process of how to set that up properly.

@TheTitansman1 3 дня назад

Are the circuits you tapped into for subs only or could you run additional speakers off it?

@kadenhorrell9691 4 месяца назад

I have a Silverado without bose , which wires do I tap into for mine

@Chipum 8 месяцев назад

Awesome install very clean… just a quick question what is the price for everything in video installed? Thanks great channel

@ProvoBeastAudio 8 месяцев назад

Sure, we linked everything in the description for the current prices.

@Alex_MKE 2 месяца назад

Why cant you connect to the stud of the battery terminal? Im having issues with either ground or power amps not turning on

@aaron44ornelas 3 месяца назад

Do light dim ? Can it mess up electrical system ?

@ksigherrera 7 месяцев назад

Great Video! Question. Can that board be used on a Non-Bose truck? Their website doesn’t have a board for a non-Bose.

@Signatureofheaven 6 месяцев назад

The amp rack from the website will not work for non bose. They say there is foam behind the seat that doesn't allow the amp rack to fit properly. Fits perfect for Bose equipped trucks

@dheasley2 3 месяца назад

Skar says these 4 8" boxes can handle the evl and svx woofers. What do you guys think about that? Everyone don't seem to think so. I find it annoying that the 8",10", and 12" boxes that fit my truck are only compatible to the lower grade woofers unless i raise the back seat and i don't want to do that.

@kevindesson6730 2 месяца назад

Would you happen to know the speakers wire colors for a 2023 yukon?

@tyroneferrell1602 4 месяца назад

Nice work where are you located??

@blackhornet25 Месяц назад

Is the lc2 or Lc7i pro needed if i have audiocontrol's dm-810 on a factory radio?

@VWfanatic8 10 месяцев назад

How does that box sound?

@andyh8239 6 месяцев назад

Did you lose the fader with this install method? I assume those are the rear speaker full range outputs, thus avoiding the need to (sum) the front highs and lows? I suppose this was for a sub install only, and no other drivers were amplified beyond the factory.

@markvveinotte1766 3 месяца назад

He tapped the subwoofer wires so no it doesn’t affect the fader and there’s no full range signal cuz of the Bose amp

@andyh8239 6 месяцев назад

In the process of installing a LC-6-1200 amung other things. Seems to me once the back seat goes back in the seat foam is going to blanket the amplifier quite tightly. (Not even sure the back rest sill even go back in with the amp mounted.) Did you have to cut the foam for this install? Any overheating issues? I drove a few miles without the rear seat and wow was that noisy. 10x louder than expected. If you do cut foam, does it increase cab noise much?

@-Primer- 5 месяцев назад

None of the channels show that, or the seat reinstalled. I have 3 amps on my custom rack and I had to do a lot of trimming and it still wont fit perfectly. The bottom of the seat is about 2 inches from going back into place. The "foam" on my 2024 GMC3500 PRO CREWCAB is not a soft foam, but more of a molded Styrofoam. Very dense, but cut well with a Oscillating Multi Tool.

@mikeganard6751 10 месяцев назад

Looks great! I have a LC7i I’m looking to install. Can I get power and ground off my distribution block instead of the amp? Also would I need a fuse for the LC7i?

@JasonWW2000 10 месяцев назад

Yes, you can get power and ground from there. Add a small 2A inline fuse on the power wire going to the LC7I.

@mikeganard6751 10 месяцев назад

@@JasonWW2000 ok thank you!

@chrismuncey6023 16 дней назад

I used the same wires for signal with a jl 10 w7 an lc2i and a 1000 watt jl amp for some reason the signal from the sub out sounds terrible and the full range signal I can't get the jl amp to cut-off at 80 do I need a dedicated sub out?? Past the lc2i? Plz help!

@gerardoreyes711 8 месяцев назад

Any idea if the set up will still work for two 10’s, or would you be able to explain what I’d have to do differently. Thanks

@Signatureofheaven 6 месяцев назад

The set up will work with 10 inch subs. Just make sure that you have the proper type of subs that will fit under your seat, recommended shallow subs, unless custom built enclosure, requires lifting the seat.

@julesbruchez-theartofgrapp9646 8 месяцев назад

Seems like a small power and ground wire for that type of draw

@travispinkerton9916 10 месяцев назад

Hopefully you respond but I’m running do jl 13tw5v2-2 wired to 1 ohm and I’m running the line out converter but not the epicenter. Will the epicenter give me more bass? My lows hit very hard and my highs hit pretty good but think there could be room for improvement…

@gerardobernardino1092 8 месяцев назад

You need a bass knob for your amp. The epicenter is used to bring out the bass that's in music such as rock, Mexican, etc.

@sebastianmartin3424 9 месяцев назад

Are your 4 8” subs 2 or 4 ohm? I’m curious to see how you wired them to get 1 ohm final impedance?

@Half_Gassed 6 месяцев назад

He literally said dvc 2ohm load skars, and then shows the wiring diagram as to how they wired them down..... it's like you didn't even watch the video 🤔

@naughtyca131970 9 месяцев назад

what is the ohm load of the bose for dash speakers? are they 3.5in size speakers and can i just get a aftermarket speaker and replace the dash speaker? thanks

@Signatureofheaven 6 месяцев назад

You can buy aftermarket speakers and drop in if they are the same size. The bose amplifier will still amplify the sound, which in turn will make them sound good. The speakers are 2.5" in the dash.

@ejy99 8 месяцев назад

Great video and very clean install. I have question that you may be able to answer so I can get my install done right. First, I have not taken the backseat off, so I cannot confirm I have the same amps in the back, but I assume so since I DO have the Bose system in my 2021 TB. I am doing a very simple install. A kicker pre-fab box, an Alpine mono amp, and a Kicker LOC. The LOC has the 12v turn-on lead coming off of it. Models below for reference. My question is, in your install you tapped into the Bose amp with the white and grey speaker leads from the blue and green wires in the harness. In every other video I have seen, people are using the yellow/yellow and black wire into a LOC to go to the mono Amp, usually in the front passenger kick panel. Is there a reason you did this? Is it because you need a full-range signal to go into the LC2? If I can get to the yellow/yellow & black wires right there in the rear near the harness, I don’t see a reason to put the LOC in the front passenger Kick panel like I have seen most do. What signal comes from the yellow/yellow & black wires? For my simple setup, what is my best course of action? Thanks for the recommendation! Kicker TRTP 10” Sub Box Alpine S-A60M Mono Amp Kicker 46KISLOC2 Speaker wire to RCA LOC

@johnspratley6691 7 месяцев назад

Same here as far as the Bose output wire. I have been trying to find a video of someone coming from the Bose subwoofer. Stumbled one would go to the door speakers, carrying the highs, when there is a input from a sub, carrying the lows. Wouldn’t the door speakers give out the wrong signals, especially when adjusting the settings on the head unit? Im sure the LC2 will make up for that but it’s probably going to have some sort of interference when adjusting on the head unit.

@ejy99 7 месяцев назад

@@johnspratley6691 I think after seeing so many videos on YT that say to use the yellow/yellow&black that is what I am going to just do and see how it works out. I am going to trace them back to where they end behind the seat versus running my LOC all the way up to the kick panel. That just doesn't make sense to me. The Amp should be able to take the full range signal, if that is what is coming through those wires (Y/Y&B), and just pull the lows using the low pass filter, at least as I understand it. I have used LOCs with full range signal before and it works fine. Ill come back on here and let you know how it goes. Thanks for the reply.

@Frankd1277 3 месяца назад

Did you find the yellow and black wires near the amp? I currently am in the middle of a subwoofer install and can't figure out what wires to connect to the loc.

@Signatureofheaven 16 дней назад

You can use the signal from the bose amp yellow/yellow&black wires to make your connections easy. You can use the Audiocontrol LC2I Pro or the Pac Audio SNI-35. If all you're doing is adding a subwoofer amp, get the signal from the rear. You just have to remove the seat.

@robm5974 5 месяцев назад

Nice craftsmanship. Question on the overall system. It seems like 1800W would be a bit overkill putting it up against factory door speakers & amp? How did it sound overall? To me the factory Bose system lacks on the mid/high range already, did the subs drown it out?

@ProvoBeastAudio 5 месяцев назад

It's what the customer wanted. Yeah, it's tons of bass, but I recommend a more rounded system, just depends on your trim and budget. If you want more direction, send me a message on facebook or instagram.

@robm5974 5 месяцев назад

@@ProvoBeastAudio good deal, thanks for the quick reply!

@Handwrench83 9 месяцев назад

23 sierra, factory signal sucks. Can't even turn my mb1024s up without the factory radio maxing out first. What do you recommend for the signal input so that it doesn't suck? Thos is a non bose stereo with an unknown line converter

@gerardobernardino1092 8 месяцев назад

LC7I with a custom harness from @Grayback1973

@user-el6ul7lk2d Месяц назад

Does the epicenter get power and ground from the bass amp or can you get it from the lc2??? Thanks

@ProvoBeastAudio Месяц назад

Both the LC2i and Epicenter need constant 12v and ground, which we snagged both from the power and ground terminals of the amplifier.

@armandojimenez3596 4 месяца назад

Hi I have a sound system but the subs are not working and the sound system is turn on

@kenacyt 9 месяцев назад

What signal is that on the plug that you tapped into? The GM accessory Kicker sub shows using a yellow & yellow/black pair near the passenger front kick panel, is this a better spot to pull the signal from?

@ProvoBeastAudio 9 месяцев назад

It's the Bose subwoofer wiring connection at the Bose amp. It's right there instead of running the wiring to the bose subwoofer in the center console.

@gyfhj 6 месяцев назад

Do you have a part number for the harness you’re using to tap into the sub wires?

@davidrendon9838 Месяц назад

What’s the Skar equivalent amp…for this set up? Thanks. Great video!

@ProvoBeastAudio 29 дней назад

With those specific subs, the RP-1500.1D

@davidrendon9838 29 дней назад

@@ProvoBeastAudio ok thanks!

@jamessmart7605 8 месяцев назад

Could 0/1 gauge wire fit through that grommet in the fire wall

@gerardobernardino1092 8 месяцев назад

Yes, it will. I have 2/0 running through mine.

@darrylm7588 5 месяцев назад

Where is the factory sub in the new GM trucks? I just pick up a 2024 AT4 1500. Is there more of a simple solution for the sub amp? I have an older Audison LRx 1.1k mono block with high level inputs, could I not just use the signal from the Bose amp and go directly into the Audison?

@jcook8191 Месяц назад

Not sure on the 24 models but my 21 model has the Bose sub in the console

@mrpanchito9215 7 месяцев назад

Did you have any problems with the noise canceling?

@ProvoBeastAudio 7 месяцев назад

This gen Silverado wasn’t equipped with anc.

@frankparisi2433 7 месяцев назад

Really good video. Why not use an Epicenter Micro. One device does it all?

@ProvoBeastAudio 7 месяцев назад

Customer provided epicenter before the install. The Micro is indeed a better choice to save space, but since it was already purchased, we used what we had.

@frankparisi2433 7 месяцев назад

@ProvoBeastAudio I ordered an Epicenter. A little pricey but a nice toy.

@404spaz 3 месяца назад

How would this affect door chimes on a non Bose amp silverado

@ProvoBeastAudio 3 месяца назад

Non-Bose means there isn't an external amplifier in most cases. The radio powers the speakers internally. If you have that setup, all you need is the GM Radio T harness and line out converter we have linked in the description. Factory radio module is behind the glove box.

@ProcessHF 13 дней назад

On the 2024s that nipple on the grommet does not exist. GM says to pass the wire through the plastic slit directly on the bottom of the grommet with a metal rod. It's a massive pain in the ass (specifically on the diesels)

@ivankorth4458 2 месяца назад

How much for an install like this

@dsgaragedavid1987 7 месяцев назад

I’m using the lc6 and I have the Bose system I’m not getting a signal from the rear speakers any advice

@Signatureofheaven 6 месяцев назад

Use the signal from the front, yellow/Yellow & Black

@andyh8239 6 месяцев назад

Did any of the foam on the seat back-rest need to be trimmed for this setup? Does the foam press up tight to the equipment / compressed?

@-Primer- 5 месяцев назад

@andyh8239 5 месяцев назад

@@-Primer- I ended up 3D printing custom brackets with brass threaded inserts. Exoxied the brackets into place and the equipment is removable. I only had to trim on small piece of foam, but stuff does seem to squeeeze tight a bit on re-installation lf the seat. I purchased a 3D scanner so I can model it better for the sub integration which is next on the list of things to do.

@-Primer- 5 месяцев назад

@@andyh8239 Well that's clever. I'm pretty well versed with Fusion 360 and/but my printer is only 230x230. The idea of printing brackets to get the amps to sit "deeper" has got my gears turning. I guess that's a new project to work on --- DAMMIT !

@andyh8239 5 месяцев назад

@@-Primer- I used a profile gauge when I made them and they worked great but the 3D scanner thats on the way should be a game changer as you can mock it all up virtually and obtain perfect profiles. Could even scan the back of the seat foam to identify what needs to be cut. I designed a holder that clamps to a capacitor which fit perfectly behind the seatbelt strap (cap locks into place with set screws and leaves behind only a thin bracket when removed. I was even able to print connectors to adapt the tweeters to the factory dash harness. I made a mockup of the tweeters I wanted to ensure they would fit (Morel 728's) as the ScanSpeak ones I planned to use had too large of magnets. I'd like to scan the doors next to see if I could put some ScanSpeak Revelator 8's in the doors. Madisound has a lot of good stuff to choose from.

@djcarkhuff 8 месяцев назад

How thick is everything in relation to the seat back? How much of the foam had to be trimmed?

@ProvoBeastAudio 8 месяцев назад

We didn't have to trim any foam, and still had decent air flow. If you have a taller setup, or an amp that runs hot, then trimming is recommended.

@djcarkhuff 8 месяцев назад

@@ProvoBeastAudioThanks for the reply. I'm attempting to install a relatively simple setup, a pair of Kicker hideaways. They're about 3 inches thick, so that's why I was curious about the foam trimming. Thanks for the heads up.

@growitwemowitllc1752 8 месяцев назад

When I go to the site for amp rack it says won’t work for mine cause I don’t have the Bose. Seem odds since the only difference is the amp in the back and I don’t have that? Would it still work?

@gerardobernardino1092 8 месяцев назад

The only reason why it says it won't work is because your truck(like mine) has foam behind the seat. And because we have less mounting studs.

@growitwemowitllc1752 8 месяцев назад

@@gerardobernardino1092 so it will some what work? I moved the foam from mine

@gerardobernardino1092 8 месяцев назад

@growitwemowitllc1752 it'll work no problem just add extra mounting brackets.

@jayh7423 Месяц назад

Hahaha please show us how you modified the rear seat in order to get it back on!!!

@anthony03241980 6 месяцев назад

Got I huge question lol what wires did you tap into on the Bose bec I’m doing a 23 with the Bose I’m just wondering what wires you used and if you had any problems I will wait till you respond before I tap into anything

@ProvoBeastAudio 6 месяцев назад

just the factory sub speaker wiring (blue and green twisted pair at the amp). That is the only factory connection.

@gyfhj 6 месяцев назад

Is there a harness for this?

@anthony03241980 6 месяцев назад

Do you happen to know what wires are what back at the amp on the Bose amp so if I do door speakers

@franciscoovilla1666 Месяц назад

I have the same install with an audiocontrol lc2i. And epicenter. But im getting a thump sound when theres no music playing Any advice???

@Signatureofheaven 16 дней назад

A thump sound? When you turn on/off the system? While you're driving?

@poloturrubiartes7622 9 месяцев назад

I have a 2020 Chevy custom trail boss without Bose. I looked up the amp rack with the link and the website said it was not compatible to my truck. In your opinion could I use the amp rack that you used or will I have to find a different rack?

@ProvoBeastAudio 9 месяцев назад

I'd reach out to sounds good stereo to see if they have a solution for your truck.

@djcarkhuff 8 месяцев назад

It'll physically fit in your truck, but not all the mounting studs may be present to secure it to the back cab wall is all.

@Signatureofheaven 6 месяцев назад

You'll need to cut out the foam and add mounting brackets to get it to hold

@drawsawyer5881 7 месяцев назад

Started a complete audio upgrade in a ‘22 this weekend. Did you have to cut foam out of the back of the seat to get it back in. There’s no way I could mount that board and move everything around without doing so.

@zachschmidt2802 6 месяцев назад

Did you figure this out just ran into the same problem

@drawsawyer5881 6 месяцев назад

@@zachschmidt2802 I got a 2000w amp behind it. Had to cut a significant amount of foam off the seat. I did it in a way that the amp is contained in one of those areas that lead to the cab vent. Closed off the other cab vent. Theory is it’s going to push all cabin air/pressure out the vent with the amp right beside it and cool it. You couldn’t mount that board without taking all of the foam off the seat. I would definitely put some sound deadening on that back wall too. For me, the real downside is not being able to access the amp without unbolting the seat.

@drawsawyer5881 6 месяцев назад

Also moved factory equipment that was back there to behind the box under rear seat. Not as clean as this install, but it’s clean enough for adding an LC2i and mids/highs amp under the passenger seat, four eights under rear seat, and 2kamp behind the seat. No wires showing. GM does kind of make hiding wires easy with their huge channels down the side. Now if they’d just unlock my ECM…

@Signatureofheaven 6 месяцев назад

The amp board is made for trucks with the Bose system.

@gyfhj 6 месяцев назад

Hey awesome video man! What are the dimensions of the amp rack?

@brockd13 4 месяца назад

14.5 x 44.5 I just copied/built my own in an hour and saved $185

@gyfhj 4 месяца назад

Me too! 💪🏼

@user-je3iz9qf8i 8 месяцев назад

Not gonna sound matt the rear wall of the truck?(Behind the Amp Rack). Might as well since you have everything out. 8)

@traycain9372 8 месяцев назад

Do you have to modify the seat any?

@ayeayeronsearcy9402 8 месяцев назад

Just had to take the foam off the back

@twomontess 7 месяцев назад

Why did you grab signal from front ? Why not the sub signal wire ? (The two Yellow wires) Now when he lowers the bass the sub goes away and when he fades or balance left to right the subs have no signal !? Second epicenter is not needed. Looks like a case of over sell to me.

@ProvoBeastAudio 7 месяцев назад

Did you not watch all the video? (Apparently not). We tapped into the Boss sub output for signal, not the fronts. Secondly, the epicenter was provided by the customer as he wanted it installed. We didn’t sell him any of this equipment as it was all provided by the owner of the truck. This truck went through two other shops before it made it to use to fix and make right.

@davidhernandez-tc7ko 2 месяца назад

Yo... send me a link for the Amp panel, that looks clean!!

@joshwright9257 Месяц назад

It's in the comments

@iwiredit 7 месяцев назад

Kicker 1800 watts @ 1 ohm means about 800 or 900 watts rms.

@ProvoBeastAudio 7 месяцев назад

Kicker puts the RMS wattage on their amps, not Peak power, sorry. This is indeed 1800 + watts @ 1 ohm per the birth sheet included with the amp.

@iwiredit 7 месяцев назад

@@ProvoBeastAudio Its good Kicker has changed and went back to there old roots. After they stopped the ZR series it seemed all there stuff was over seas and over rated power the quality went down hill in the mid 2000's But seems they revamped. So good on them.

@civstu 8 месяцев назад

Are you able to reinstall the rear seat back or are you permanently leaving it off?

@Signatureofheaven 6 месяцев назад

The back seat goes right back on.

@jayh7423 Месяц назад

Ahahahahhahahahahhaaa No. It cannot. You have to cut the hell out of the foam.

@juliosandoval8244 5 месяцев назад

Why do you need a lc2i and a epicenter?the lc2i has the same function expect its a high n low adapter with bass enhancement plug in bass knob also

@ProvoBeastAudio 4 месяца назад

LC2i doesn’t have any eq capabilities, just a line driver and bass roll off correction. The epicenter has a line driver function as well, but also eq function. If you want an (almost) all in one, check out the epicenter pro.

@juliosandoval8244 4 месяца назад

@@ProvoBeastAudio I've installed the epicenter pro couple times.

@user-zo4bw2dy2x 10 месяцев назад

I have a 2022 chevy silverado non bose refresh interior would Iike to add a 4 channel amplifier for the doors without the t harness because I have th e black and gray plugs and can't find that harness anywhere.

@ProvoBeastAudio 10 месяцев назад

Hey Happy to help. Send us a message on our facebook or instagram pages and we can help find a harness that would work for you.

@gerardobernardino1092 8 месяцев назад

John can custom make your harness @Grayback1973

@kelaro75 7 месяцев назад

I got with John for a integration harness for my 2024. He responded promptly and asked for specific info and now I'm just patiently waiting for my harness.

@user-zo4bw2dy2x 9 месяцев назад

Did you have to cut the foam out the back seat in order to mount the amplifier

@EricH0skins 8 месяцев назад

im more than confident they didnt say that bc yes they did, big time…i know bc im finishing mine right now

@djcarkhuff 8 месяцев назад

@@EricH0skinsWould you mind sharing any tips? I'm attempting to mount a pair of 10" Kicker hideaways on the cab wall of my '21 Silverado and while I have space to mount them, I'll definitely have to trim the seat foam. Thanks for your time.

@gerardobernardino1092 8 месяцев назад

@djcarkhuff I just trimmed as needed for my amps to fit. I had to mark and cut, mark and cut. It was kinda annoying but I wanted to leave as much foam as I could.

@zxautogiro 6 месяцев назад

⁠@@djcarkhuffI’m thinking about doing the two kickers 46hs10 hideaway behind the beck seat wondering if some foaming trimming might fit those two I got I 2024 at4 2500hd.

@cmwilliams357 8 месяцев назад

Hello sir, Is there a amp rack for a larger amp for this truck?

@ProvoBeastAudio 8 месяцев назад

Check out sounds good stereo to find the one that fits your needs.

@cmwilliams357 8 месяцев назад

Thank you sir 💝

@ayeayeronsearcy9402 8 месяцев назад

I followed your setup. I have the 23 silverado with bose. When I unlock the doors the amp comes on? What could be the cause of this? I'm assuming its the remote wire but just curious how to set it up to where it doesn't turn on til the truck is on

@Signatureofheaven 6 месяцев назад

You will need to change the way the LC2I comes on. You'd have to set it to Audio, or you'll have to run a remote wire to your fuse box.

@franciscoovilla1666 Месяц назад

Im having the same issue. When unlocking the truck all my system comes on. And sometimes im getting the thump sound of the subwoofers when theres no music playing Any advice??

@ayeayeronsearcy9402 29 дней назад

@franciscoovilla1666 same here. Been looking for a fix.

@davidrendon9838 25 дней назад

What did you end up doing?

@Signatureofheaven 16 дней назад

Depending on the LOC you're using... You will need to change the way the LOC comes on. You'd have to run a remote wire to a fuse in your fuse box that only comes on when the truck's ignition comes on and turns off. Sometimes the USB charger will work, or another accessory type fuse.

@bmanslayer94 7 месяцев назад

I got a 2024 silverado with bose pre installed and for the rubber grommet near battery terminal it doesn't have the accessory plug for me to feed through for positive. Any ideas?

@Signatureofheaven 6 месяцев назад

Check both sides of the truck under hood. Should have one on either or both sides

@kelaro75 5 месяцев назад

My 2024 didn't have a nipple. I just slit the big grommet on the passenger side.

@Signatureofheaven 5 месяцев назад

Good deal, good to know. Thanks!

@Bill-ck3lo 8 месяцев назад

Excuse my dumb question but how does the signal get to the speakers? Did you run speaker wire from the amp to each door? Newbie trying to learn here

@Signatureofheaven 6 месяцев назад

No, they didn't run new wires. The LC2i Pro is a line output converter, it takes the high level signal from the factory speakers (usually 1, or 2 speakers) and converts that high level signal to low level for the subs (for the bass). It's all done inside the LC2i.

@brianflackwatch 2 месяца назад

The amp they installed doesn't amplify the factory door speakers so don't need wires from the amp to the doors. They are still powered by the factory amp. The amp they installed only powers the 4 subs under the seat that they installed.

@bernaolivas 5 месяцев назад

I believe you should have used the main output from the lc2i to the epicenter instead of the bass output

@ProvoBeastAudio 5 месяцев назад

No, we used the bass output. thanks for playing.

@markvveinotte1766 3 месяца назад

Ya I know it sounds like shit since he used the factory sub signal. Epicenter needs a full range signal to work properly. Need to tap front door speakers instead. Nice set up though

@ProvoBeastAudio 3 месяца назад

Unless you've done one yourself, it sounded fantastic. factory Bose amp has passive crossovers on the door speakers so the sub signal was the real only option outside of adding a DSP. Non-amplified version has a full rage signal going to the front door 6x9's.@@markvveinotte1766

@markvveinotte1766 3 месяца назад

Yes I have done one and that’s why I say that. Sub signal is also crossed over and has too much of a bass signal for epicenter. It’s works for that loc but I found epicenter not so much. Needs min 200hz-1000hz to work properly

@stephen68889 Месяц назад

@@markvveinotte1766 I am looking to install a set up similar to this, with an lc2i pro and an epicenter with a bose system. Are you suggesting that using the yellow/yellow black (door speaker) would be the better option here since both the sub signal and door speakers have passive crossover?

@user-iv1jl5gi7t 6 месяцев назад

Cuanto cuesta un equipo de sonido así,con instalación y todo ,Gracias

@juliosandoval8244 5 месяцев назад

Como $1600 todo

@Jdawg-hn5pd 2 месяца назад

What’s the total for all this

@anthonyrosati8707 3 месяца назад

Clean like ya nanas living room son

@stevearreola4057 8 месяцев назад

Where are you guys located

@ProvoBeastAudio 8 месяцев назад

Utah!

@AhmedAddas 7 месяцев назад

Why did you keep using oem bose amp?

@jcook8191 Месяц назад

Looks like The amp is still being used for factory Bose speakers and the Bose sub.

@jonatana8531 5 месяцев назад

How could I add a 4 channel amp to the Bose? I have a 22 1500 ltz with Bose

@ProvoBeastAudio 5 месяцев назад

There isn't an AmpPro module yet to replace the OEM bose amp, so you will have to tap in for signal after the amp. There are Pac T harness available to help you do that, but you'll need some sort of high power LOC and such to accomplish this for internal summing, etc.

@jonatana8531 5 месяцев назад

@@ProvoBeastAudio I have a loc on a sub right now tapped into the speakers. I want to add a 4 channel so would I just cut the front and rear speaker wires into a lc5i and replace my loc from the sub into the lc5i then run my own wires door to door into the speakers? My speakers are also upgraded to Focal speakers. Cutting my harness isn’t my issue I can do that with no issue, I just know not to cut the front tweeters since that’s for phone calls etc..

@ProvoBeastAudio 5 месяцев назад

No need for cutting harnesses, there is a T harness you can use. Yes, reroute all into the LC5i or lC6i where you can do internal summing for your amplifiers.. amzn.to/48fWiZy@@jonatana8531

@miguelmontes2712 8 месяцев назад

I have a 2022 Silverado lt refresh and I have 2 amplifiers, one for 4 8” basses, another for the 4 door speakers and the 4 speaker amplifier turns off. They tell me that I have to change the battery. It is true to your experiences that you have had. or it will be a bad installation I hope you can help me

@gerardobernardino1092 8 месяцев назад

Check for any loose power and ground cables from distro block to amp. Check ground links and fuses to make sure they're not loose as well.

@miguelmontes2712 8 месяцев назад

@@gerardobernardino1092 The audio shop tells me that my battery voltage is low, do you know what voltage my battery needs for it to work well, they say my battery is the problem and they say I need a new AGM battery, but I think it's something else.

@gerardobernardino1092 8 месяцев назад

@miguelmontes2712 while running atleast 13+ voltage while off 12ish which is just resting voltage

@miguelmontes2712 8 месяцев назад

@@gerardobernardino1092 It's strange, my truck is 2022, my battery is not very old, but it's not enough for the sound system. Can you recommend a battery for the sound system for the 2022 silverado 1500 lt?

@gerardobernardino1092 8 месяцев назад

@miguelmontes2712 before buying a whole new battery( which I doubt you need a new battery) check what I stated before. Also, you can check your voltage on the truck in your info tab on the truck.

@alexanderstein5379 10 месяцев назад

What about the ANC MICS?

@ProvoBeastAudio 10 месяцев назад

Most trucks don't have ANC in this generation, unless you have mics in the headliner in the back seat (not above the driver / passenger). If you have ANC, there are bypass harnesses available which makes it easy to complete the process. Our LTZ Bose trim did not have ANC.