Тёмный

2019 Honda Odyssey Front Lower Arm Replacement POV ASMR W/O BGM FYB.. 👀🔧  

TE VIDEOS
Подписаться 96 тыс.
Просмотров 3,9 тыс.
50% 1

Опубликовано:

 

11 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 23   
@Sean89us
@Sean89us 23 дня назад
My good man you are my hero for posting this video. As others have stated this is the only resource out there apparently
@we6060
@we6060 3 месяца назад
Solid work! Very fast, efficient and skillful. Had to laugh that you will never hear that from a supervisor. Wish all mechanics had your skill and attention to detail.
@Skvelysprt
@Skvelysprt 2 месяца назад
This is the only video of this I have found. Thank you thank you! Although I’m not nearly as fast as you in the driveway.
@josephnavarro3620
@josephnavarro3620 2 месяца назад
You're very efficient Tyler. I like the cut of your jib.
@JamesCrow_crowbar
@JamesCrow_crowbar 2 месяца назад
Thanks for the video! Helpful to see the process end to end. A couple questions: Do you have to check the alignment after? Does Honda specify that the castle nut and bolts should be replaced rather than re-used?
@vinnyd9085
@vinnyd9085 3 месяца назад
Quick question. Good job btw. What was the initial tool you used called to pop out the bolt from the brake assy. Thanks. Again solid work.
@TEVIDEOS
@TEVIDEOS 3 месяца назад
Ball joint separator, I have a few linked to my link tree website under the "ugga dugga" section 😁👌 linktr.ee/te_videos
@vinnyd9085
@vinnyd9085 12 дней назад
@@TEVIDEOS thank you very much loved your video and helped me out as well.
@alexandercuello3168
@alexandercuello3168 3 месяца назад
Excellent job, I’m surprised that it needs to be replaced being from a 2019 Oddy. I did the same job but to my much older 07 Honda pilot they, were the original control arms.
@DamascusSyria..
@DamascusSyria.. Месяц назад
Very good
@maplegecko
@maplegecko 2 месяца назад
Great video. Do you have torque specification for tightening bolts?
@04swiftstang
@04swiftstang Месяц назад
Just a few ugga duggas there bud....😎..
@vinnyd9085
@vinnyd9085 7 дней назад
Yes, is there a torque spec?😊
@map7463
@map7463 3 месяца назад
Did that control arm really need replacing? Bushing looked intact.
@PRO4XKEV
@PRO4XKEV 3 месяца назад
Cracks and tears.. rock salt de icer from winter roads destroys rubber. Dry rot.
@ScionOfFlame
@ScionOfFlame 3 месяца назад
Gotta be careful on Colorado roads. Excessive salt on 'em bud.
@map7463
@map7463 3 месяца назад
I don't have to worry about that in Southern California. Would it make sense to brush a coating of silicone grease on the rubber bushings at installation?
@bigdaddymak1439
@bigdaddymak1439 3 месяца назад
​@@map7463just enjoy your salt/rust free California there Bud!! 😂😂
@TEVIDEOS
@TEVIDEOS 3 месяца назад
Bushing was torn about half way through, hard to see when it's out of the vehicle. This was someone else's recs. These bushings getting torn is rather common, I usually don't recommend them unless they are completely torn through
@raymakkouk4697
@raymakkouk4697 3 месяца назад
New Carter pin? Dont be cheap for like $2 dollars 🤨
@TEVIDEOS
@TEVIDEOS 3 месяца назад
The cotter pin is re usable and completely fine. That would be a solid waste of 2 dollars lol
@H8HotWeather
@H8HotWeather 3 месяца назад
Honda cotter pins do not need to be bent. They slip in and self locks. It’s not the ones you bend…that kind i would not reuse
Далее
КУШАТЬ ХОЧЕШЬ? #дистори
00:15
Просмотров 142 тыс.
2007 Honda Odyssey Lower Control Arm Replacement EASY
18:46
How To Replace Lower Control Arm Bushings In Car!
10:59
Replacing Lower Control Arm
11:00
Просмотров 1 млн