3 MOST NEEDED MODS for DIY Powder Coat Guns (Eastwood/Harbor Freight)

Подписаться 9 тыс.

Просмотров 16 тыс.

50% 1

The "3 most needed mods for the DIY powder coat guns" video is a must watch if you are just getting into the DIY powder coating scene, or even if you've been doing it for awhile. Everyone will get something out of this video! I'm in the Amazon affiliate program and receive compensation when you make a purchase through one of my links. It adds nothing to the cost of this product, I just receive a small commission which helps my channel. Thank you for watching.
SUBSCRIBE TO CYCLE FAB : / cyclefab
LINKS to my DIFFUSER KITS
EASTWOOD Diffuser Kit: www.ebay.com/i...
HARBOR FREIGHT Diffuser/Mixing Tube Combo Kit: www.ebay.com/i...
HARBOR FREIGHT Diffuser Kit: www.ebay.com/i...
HARBOR FREIGHT Mixing Tube only: www.ebay.com/i...
FAN NOZZLE-HF1 for Harbor Freight: www.ebay.com/i...
FAN NOZZLE-E1 for Eastwood: www.ebay.com/i...
LINKS TO A FEW OF MY POWDER COAT VIDEOS:
• DIFFUSER COMPARISON: S...
• POWDER COAT GROUNDING ...
• NEW!! MIXING TUBE!! ...
• EASTWOOD FAN NOZZLE UP...
• POWDER COAT GROUNDING ...
• EASTWOOD INPUT TUBE MO...
• DIFFUSER INSTALLATION
SILICONE PLUGS for POWDER COATING: www.amazon.com...
SUNFLAG JIS SCREW DIVER SET: www.amazon.com..."
VEVOR ULTRASONIC LINK: s.vevor.com/bf...
Special Discount Code VVUC10 for 10% off VEVOR Ultrasonic Cleaners
VEVOR contact info: www.vevor.com/...
CREWORKS ULTRASONIC CLEANER:
www.amazon.com..."
MUSIC BY:
www.epidemicso...

Опубликовано:

8 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@tigeryorkie07 Год назад

Got another subscriber Larry, dispite the audio! Thanks 🤘🏽

@CycleFab Год назад

Thanks, Mike McC! Hope to keep bringing you interesting content.

@troyhodulik5542 8 месяцев назад

Can anyone please tell me how to remove the siphon tubes to replace the cap on the gun? I dropped my Eastwood Dual Voltage gun and cracked the lid. Thank you.

@troyhodulik5542 8 месяцев назад

All, I figured it out. The tubes are threaded. I took a med pair of Channel lock pliers and carefully loosened them from the body of gun. There WAS some type of thread locker on the thread so just go slowly and take your time. I then took a spare cap and drilled 2 holes in it using a 13/32 bit. I also put 2 new o-rings on the siphon tubes. I used a Harbor Freight o-ring kit and used the P10A rings which are 9.8 x 2.4mm. The only thing that takes some time and attention is getting the hole-to-hole spacing correct and the correct position on the cap itself so it fits properly in the flat of the gun body. I hope this helps someone who may have dropped there gun and cracked/broken the lid. Feel free to ask any questions.

@godofrock 4 месяца назад

Spend some of those millions from the diffuser sales on a new mic.

@Blou55 11 месяцев назад

I like your video, helpfull. What do you use as air filter on your gun... Thanks

@CycleFab 11 месяцев назад

Lowe's brand, KOBALT.

@brianl1049 4 месяца назад

I have all of your mods for the HF gun and did the ground pole as well. Oddly enough the gun shoots HF powder without issue and it sticks no problem. But I cannot get prismatic powders to stick to anything. All same process and equipment. HF gun too low of voltage you think?

@CycleFab 4 месяца назад

Some of the prismatic powders have issues in DIY guns and I have no idea why.

@willwalker5594 6 месяцев назад

Which gun is the better gun to start with Eastwood or Harbor Freight?

@user-ic2cw6qz2s 10 месяцев назад

Have you had any experience with the Redline EZ100J? My wife bought me one for my birthday and I have not set up my shop yet. I build and sell 55 gallon drum smokers and will be doing the sandblasting and powdercoating myself instead of subbing it out. TIA

@CycleFab 10 месяцев назад

No, I have not used that brand before. Good luck on your endeavors.

@apitochelli 6 месяцев назад

love the video! I'm doing some reading as I'm waiting for my Eastwood to arrive, I started to think if there would be any gain that were noticeable to make the pvc attachment metal to better charge the powder coming out? if it were connected to the diffuser would you notice a difference?

@CycleFab 6 месяцев назад

Thanks! And no, I haven't thought of that. Thanks for commenting!

@Phil4013 Год назад

Hey sir! What pressure do you recommend for the Eastwood? I run at about 5 psi but some powder just doesn’t get mixed up. Prismatic white pearl. I put about two inches in the hopper. Any advice would be appreciated

@CycleFab Год назад

I run at about the same starting off and adjust accordingly, not all powders flow the same. Also you might want to check out this video if you haven't seen it yet... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5tarIOt5Z-s.html