3D Printed RC Air Boat /Swamp Boat

Подписаться 2,5 тыс.

Просмотров 8 тыс.

50% 1

3D Printed RC Air Boat /Swamp Boat
Material PLA+ , PETG
Brand Esun
Air Boat /Swamp Boat
Spec.
Lenght 480 mm
Width 280mm
Height 280mm
ESC. 30a
Lipo Battery 3S 1500mah 100c
Brushless Motor 2217 1750kv
Propeller 8x4X3 3 Blade
Servo 9g MG
Radio
TX Futaba 3pv
RX Corana 4ch
STL File www.thingiverse.com/thing:593...
Please subscribe to our youtube channel / @mr.rc-creator

Хобби

Опубликовано:

27 мар 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 47

@gerardtonno9458 Год назад

Hmm, this may wind up being my new rescue boat. Make a fitting to hold and push a U-shaped PVC pipe and BINGO! No more worries about the weeds! Thanks for a great design!

@Mr.RC-Creator Год назад

Thank you very much for your comments.😉

@MrJob91 Год назад

Looks very fun!! Well balanced machine

@Mr.RC-Creator Год назад

@Job91 Thanks😁

@keybrent64 Год назад

Saw this on thingiverse today. I gotta build this!

@Mr.RC-Creator Год назад

It 's fun. 😀

@eurobeatmachinist732 Год назад

Super cool!

@Mr.RC-Creator Год назад

Thanks.😁

@mirafly2007 11 месяцев назад

Looks good might just print this 👍🏻

@Mr.RC-Creator 11 месяцев назад

Thanks a lot. 😊

@bchobby Год назад

Very cool!

@Mr.RC-Creator Год назад

@BC Hobby. Thanks,😁

@Desguace_rc 3 месяца назад

👍

@Mr.RC-Creator 3 месяца назад

Thanks.😁

@Skalamodelskibe Год назад

Great build :-) but it looks like you did some additional design of the cage and seats as they are not in the file set from "Cr. Slightly Abnormal STL File" anything you want to share :-)

@Mr.RC-Creator Год назад

www.thingiverse.com/thing:6004487/files

@Skalamodelskibe Год назад

@@Mr.RC-Creator Thanks, looking great think it will be the next project for the Bambu X1C

@Skalamodelskibe Год назад

@@Mr.RC-Creator Downloaded the files and there seems to be som issues with them, looking at your nice video, if I want to use "Swam_boat_Tower_Gruad_Mount" I'm missing the Plate_mount that fits that. Also the Gruad set-up is a bit tricky to figur out based on the different files that you have uploaded.

@Prelude_user2022 Год назад

for the rear upper deck, did you cut down the gaurd mount and made your own? i see the files are there but there's no option for the one without the guard mount

@Mr.RC-Creator Год назад

Try agian 🙂www.thingiverse.com/thing:5938567

@lizilee8473 9 дней назад

Thanks for the sharing. I was just started this build. There is nowhere I can find the servo box stl file（the green piece at 1:20 of the video）. Would you mind fix that on thingiverse? Thank u very much.

@Mr.RC-Creator 7 дней назад

Sorry to rate reply!! you download Agianwww.thingiverse.com/thing:5938567

@lizilee8473 6 дней назад

@@Mr.RC-Creator Thank u so much. Just in time. I was planning to do the assembly at the week end：）

@t_browell1527 Год назад

what parts was used for the steering love the build

@Mr.RC-Creator Год назад

@T_Browell152 Large dual rudder control servo!!

@t_browell1527 Год назад

@@Mr.RC-Creator thank you so much!!

@Mr.RC-Creator Год назад

😁

@christopherlewis5849 6 месяцев назад

how do you mount the swam_boat_Tower_Gruad_Mount to the Swam_boat_Plate_mount 2. the one one the plate mount is smaller then the tower gruad mount

@Mr.RC-Creator 6 месяцев назад

I'll check the file again.

@1983cll 6 месяцев назад

Ok thanks

@1983cll 6 месяцев назад

@@Mr.RC-Creatori love the boat. I done printed everything but that then peaces

@Mr.RC-Creator 6 месяцев назад

@@1983cll Try agian

@dr.markusseifert5963 12 дней назад

Hello, can you please publish the stl file for the servo mount Thank you

@Mr.RC-Creator 10 дней назад

File name! Swam_boat_mount_motor_pro.

@dr.markusseifert5963 17 часов назад

Thank you for posting the servobox.stl

@larz0001 Год назад

i just recently downloaded files off of thingaverse and i am printing now, there is one file im not sure on and that is the foot box, when i open the file in the slicer programe there is nothing there, am i doing something wrong ? everything else has printed fine im looking forward to this awesome project

@Mr.RC-Creator Год назад

Thank you so much!

@larz0001 Год назад

@@Mr.RC-Creator any idea on the box foot file

@larz0001 Год назад

i got it figured out ,, there was a problem with my slicer programe , i got it sorted now and i am printing box foot now

@Mr.RC-Creator Год назад

@@larz0001 I don't remember! sorry🤔

@larz0001 Год назад

All built now just got to install radio and motor