Fantastična igračka! Ruida kontroler je po meni jedan od najboljih. Ono što možeš eventualno napraviti je kupiti dužu lasersku cijev (50 W pa nadalje) te PSU i napraviti zaista dobar stroj. I ovako je dobar, ne kažem. Kad primjetiš da ti cijev daje slabiji izlaz, uloži malo u novu cijev, PSU i možda optiku - bolja leća čini čuda, čak i na mom malom K40 laseru.
We found it's better to separate the air & water power from the laser. These Chinese lasers switches & fuses don't hold up. Also saw a little better stability of laser etch/cut. Just a suggestion.
This is an old video but like most things from china the lasers have not changed much mine looks identical to yours but it does not engrave correctly cuts fine and accurate if you still have this any chance you could send me a copy of your machines settings. I have both lightburn and rd works installed so what ever you have would be appreciated. machine and vendor settings are what i am looking for as I believe it is a timing issue with the laser firing.
@@BuBizgb ma iznenadilo me što je na hrvatskom zbog naslova. dobre košarice. pogotovo tram na kraju. ako se to može kupiti, molio bih te za neki kontakt. i poslušaj rap EP na mom kanalu kad uhvatiš vremena :D
Marko bravo, prvo 3D printer a sad ovo, super! I u KA ima mali CO2 laser samo vlasnik Marin i Kreso trebaju naucit kako ga koristiti, nema se vremena :)
@@BuBizgb pozdrav, planiram da kupim ovakav laser pa me interesuju neke inf. Kako bi mogli da uspostavimo kontakt? Ili minovde napisi jesi li zadovoljan s obzirom da je imas već neko vreme?
@@Marko-rt5yd zadovoljan sam ... vrijedi te novce! Treba nauciti raditi s tim, bit oprezan, ne pretjerivati s brzinom i snagom i eto ... za mjesec dana ce biti 3 godine od kad sam ga uzeo ... jos uvijek radi ok! Trebalo bi neke stvari malo bolje podesit i redovnije odrzavat ali eto ... pili jos uvijek! :D
@@BuBizgb oko 1000e je kod nas. Imam ponudu da radim nešto sa tim laserom a nisam radio sa njim nikad. Radio sam sa cnc glodalicom tako da sto se tice smanjenja brzine nije problem 😃 Seče MDF od 3mm?
Sorry for a question? If this machine works well to make trophy plates the plates are .015 thick metal and engravering information in round medals, I would appreciate an answer thanks
Znam da nije. Pogledao sam sve cijeli njegov kanal prije nego sto sam kupio stroj i znao sam sta kupujem. Svejedeno radi vec 3.5 godine i za te novce je super. Isplati se. Takav stroj nekog poznatijeg brenda je 5.000€ - 10.000€ ... ovaj kosta samo 1500€ i jako brzo se isplati....
@@BuBizgb Upravo sam kupio onaj mali K40 laser cutter/engraver. Isto tako kinez tvrdi da je 40, no nije ni 30W. koliko meni treba, dosta bi bilo i 10W ali da je malo veća radna površina. K40 ima tek 20x30 cm radnu površinu, što mi je za sada okay. Russ Sadler (taj jutubovac) je kupio 60W cijev, no mjerio je više od 70W, tako da je ugodno iznenađen. Ovo sam našao na aliexpressu, a šalju iz češke, tako da neće biti carine. Ma, u pravu si... bitno je da je mehanika precizna i da je površina dovoljno velika, snaga je manje bitna.
Hi, Great videos. I am having issues getting my machine to work. I cannot connect the machine to my computer. When I go to load a file up it does not appear on the Display on the machine. Also, there is no red LED working on the machine. The laser head is stuck in the middle of the machine and will not move when I turn the power on. Any Suggestions?
You can try with USB drive. In RDWorks SaveToUFile. Then on laser, read UFile and copy to memory. Watch videos from this guy ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YvrMeUUzaBo.html. There is good FB group try ask ther ... facebook.com/groups/LaserEngravingAndCutting/
Hello sir . i m a pfofessional CO2 cuting machine worker .I want to knwo what materials do you want cut and the thickness .let's talking online .whatsapp + 8613127135107
Hello, please I need help. I have this machine but unfortunately I am finding it hard to get started. I need a video guide. Most especially the graphics and the best software to use.
It is possible to cut 1.5 mm aluminium and 1.5 mm mild steel in this machine ? If it's cut then in how much pass this machine cut material? If you also know speed mm/second then also share with me.
Hey! Very nice video ! Do You work in Photoshop or Corel? I think that making it in (drawing) Corel or any other program is the hard part. Any advice is welcome! Thanks for the video
Hi, you need vector graphic. So Corel or Adobe Illustrator or free Inkscape. I mostly use CAD software like SolidWorks and export to .dxf. Easiest to open in this software is .dxf and .ai
I cut one by one. I think it is too weak to cut multiple boards at once. It is difficult to get non-bent material and the focus(the distance from the lens) is very important for a good cut. Maybe 60-80W laser could cut it. This machine might cut two 3mm plates at maximum power, but the first would probably be burnt a lot ...
super , drugar..Lep video!. pitanje: zasto je ona "fioka" sa servo motorom? pretpostavljam da nesto pomera, ali ne mogu da skapiram za sta to moze da sluzi?...
i.ebayimg.com/images/g/PyMAAOSw4shYAyne/s-l1600.jpg e hvala na odgovoru, ali izgleda da se nismo razumeli, a ni ti nisi dobio taj dodatak. Izgleda da je to rotacioni deo da rotira cilindricne materijale? Sad sam istrazio. Daju sada uz isti tvoj laser . Nema veze. Svako dobro
You can cut it, but you need to know the thickness.I am a professional worker of C02 cutting machine.You can tell me the thickness of the material you want to cut.I will check the power supply and model whatsapp + 8613127135107 for you
@@Egg1456 I think that is ok .We have high power laser machine .sir Do you mind give me you whatsapp or e-mail ? I send you cutting list and confirm whice machine is suitable for you
Hi, I just got one similar to this one. Did yours come with a driver for your computer to read it?. I plugged mine with the included midi cable but nothing pops up.
Pozdrav, ja sam u procesu kupovine jednog ovakvog stroja samo nikako da se odlucim koji bi bio najbolji za moje potrebe :) gledam 40w i 50w i svi su relativno skupi pogotov sto me jos brine da li ce me cariniti ovi nasi :) Ja cu najcesce rezati sperplocu od cca 3mm pa me zanima koliko brzo cudo moze rezati?
@@BuBizgb jel preko alija ebaya ili nesto trece? :) ja pikiram na 40x40 za sad jer ovi veci su dosta skuplji a i u planu mi je CNC pa mi se bas ne uklapa u financijsku konstrukciju :D
Pozdrav, to ti je lutrija, cijevi su jeftine kineske, od 500-2000h ... moj sad radi godinu i pol, ne radim previse na njemu ... mozda oko 400h ... cijev kakva je unutra je oko 300€. Bio bi odlican za brodomodelarstvo, ja ga koristim za aviomodelarstvo (:
The laser beam passes through the lens and must be in focus, at a certain distance from the material. The length where the focus is depends on the type of lens that is in the machine. I therefore use this red acrylic tile to know there is a good distance from the lens to the material
Hey man, we are looking at also getting one of these for us here in South Africa. Do you think it works fine? Any specific troubles you had that we should lookout for? We are looking at the 60w option Looking forward to hearing from you Kind Regards
For that price is great. My both PSU died. One was easy to repair for few € other one for tube I needed to buy new one, about 70€. Power is weaker then adverises. For best results you need some time to align mirrors, maybe get better ones. Get spare lens. If you will work a lot you need good cooling sistem like cw5000. Install mA meter to make sure you are not overdrive tube. Never put it on 100% power, watch mA meter ... and use less power and lower speeds ... u will learn by doing it! :)
Does the laser engrave on glass ? . Does the laser laser engraves on cylindrical shapes? Is there a chance to engrave something in metal ? I care about marking things. Like a glass statuette, a cigarette lighter.
Yes it engrave on glass ... check this channel for more info --> ru-vid.com/show-UCqCyShJXqnElPTUnxX0mD5A You can engrave cylindical shapes with rotary attacment tool, I got it with my machine but still didn't try it. :) 50W is too small for metal, but you can mark some things, check that channel and google CerMark. I wouldn't recommend to engrave cigarette lighter if is gas inside :) Anodized aluminium can be good for engrave ... laser will remove just coat ... I tried few times, it looks good!
I don't have a lot of photos, I'm lazy :) I'm building mini photo studio soon ... have all the parts, but no time :) few photos here --> drive.google.com/drive/folders/0B6nib3dC1LZkSXFGandERGJ3Vk0
It runs ok. You can get some better results if you change some parts like mirrors, lens, tube, PSU (: You have to have some basic technical knowledge, watch at least first 20 videos from this guy --> ru-vid.comvideos?disable_polymer=1
Epilog is good brand. It must run better than ebay laser. You have to decide what is best for you ... but if you can afford and you have space buy bigger than 500x300mm
Try it yourself. Engrave about 150mm/s 25% power ... cut 10mm/s 65% power ... try to install amper meter to be sure you don't overdrive tube. On mine 70% power is 14mA and that is maximum for that tube ... so 70% is actually 100%
Ja imam laser isto od 50 w... ovaj tvoj je noviji i moderniji cini mi se.,ali rade isti posao,htio sam te pitat koliku debljinu drveta i pleksija moze tvoj laser rezat.?
Hi, I'm not sure ...probably yes but google more. I cutted 10mm airex in one pass very fast, 15mm plexiglass in 3 passes :) www.instructables.com/answers/Is-neoprene-suitable-for-laser-cutting/
Hi, I made my own turn table just for videography and photography ...something like this --> ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Euaet3GfeqU.html LED base are from --> www.xstron.com/
I got compressor with machine! It is realy small and air pressure is just a little to help, but is much better with that and safer. You can use something small like for aquarium or similar. You see mine od 5:37 nothing special
It can work with a rotary.Our factory comes from Shanghai, China and also produces the same machine. If you need more information, please contact: Whatsapp/Wechat/Skype:+86 15696788493 Email: jenny@shcmlaser.com
Vrijedi, moj jos radi. Ali koristim ga za hobi uporabu. Ne bi preporucio, bez nadogradnji da radi kao radni stroj 8 sati dnevno. Za par sati tjedno je ok!
For this price is great! 24V PSU died after few weeks, friend repaired it for 3€ ... fan from ventilation was stuck with few kicks it spins again :) ... I'm happy with results but need to align mirror, buy new better set, and better lens! I only have 100h on tube ... it is fine ... planning to upgrade it to real 60W ...It is good buy, good for hobby and side jobs!
Hello, This is Cora from Jinan Ginchoor CNC Equipment CO., LTD. We are a leading manufacture of cnc router machine and laser machine for more than 10 yearsin Jinan, If you are interested in laser machine, Please contact me. Email: info@ginchoorcnc.com whatsapp: +86 13791025737 skype: +86 13791025737
Hi BuBizgb, I need your attention please! I own the same machine but unfortunately I've touched the death button. I need the RDVSET and RDUSET files to get back online my machine. PLease can u share with us this files? I know there are a lot of begginers worldwide who made the same fatal mistake and we need help! Thank you (the chinese do not understand english, they made me an offer to resale their machines instead of sending the files, lol)
@@BuBizgb No, bad 4 me. It happens like this. I saved the files on a stick (USB Key). Before to check the stick I've turned the machine to the fact para settings, thinking the parameters were of the laser machine producer, instead were the Ruida controller parameters, so when I tried to install the files , I've understand that I've lost the stick (stupid enough, but this is it, nothing can do, 4 years ago I've done it). So now I am searching all over the network this files, so easy to save, so easy to lost, god dam'it. I know how to do it now, all that I need is a functionally 50w machine
Marlon Brando imam ga tek 10ak dana, radna povrsina je 500x300mm ...ljudi stvarno svasta rade, papir, plexi, razne vrste drva, tkanina, koza, graviranje na staklo, case, kamen ...jos nisam stigo sve isprobat :)