53. Seep Point Motor Install and Wiring, Basic Mimic Panel Double Slip Install 

Fantastic masterclass in double slip wiring. Clear and logical explanation. Very much appreciated Mark.

Great video Mark Ive been having major issues with two points and a double slip would solve this but being new to hobby was scared to use a double slip but you have now made it simple thank you

Hi Mark, Being of an age where working under the baseboard is nearly a ‘no no’ I have developed three ways of installing Seep motors from above. 1. I prep the wiring are you have so clearly illustrated. 2. I have made a jig to identify the fixing holes for the point motor above the baseboard. 3. I drill and csk clearance holes for 4BA csk screws. I ‘tap’ the holes in the motor base 4BA (The holes as purchased are the correct size for tapping). 4. Offer up the Seep motor from below and hold in place with a crock clip. 5. Fit the 4BA screws and retain with A pair of 4BA full nuts, lock-nutted together. Alternatively, I have also glued the screws into the csk holes thus creating a stud onto which the nuts are fitted. An other alternative is to super glue One (1) nut centrally over the fixing hole and ensure the csk screw can be accessed from above for long term access. This last method I use for points long term clear of any obstructions. These methods work for me being a much more comfortable options for those wanting to avoid working from below the boards. Happy Modelling T🚂

One of the most comprehensive and easiest to follow tutorials I've seen about wiring and those devilsome double slips! Thanks Mark...

Nice to see someone using good old paste flux. :)

You are very clear and concise in your videos. A joy to watch.

At last I’ve been watching several people trying to explain how to do this and I must say your tutorial is the most understandable I’ve seen. I can do it now thanks

This is gold! Superb video :) thank you so much!

Thanks mark really good informative video I'll be wiring mine properly tomorrow cheers kev

Thank you! You've shown exactly what I've been trying understand with installing a peco double slip!

Extremely informative presentation. As a result of watching, I am now confident to proceed with the installation of my Peco single slip.

I want add my thanks to all the others here. This is great. I'm using SEEP point motors you have made it much easier for to install them.

Well described and presented, Mark. Very steady hands! No JD's the night before!

Such a helpful video. Can't wait to see the LEDs wired in to the mimic panel. Cheers.

Thank you. Greetings from Germany 👋

Hi mark just an update I've got my double slip wired in and working perfectly thanks again for the video showing me how kev

Great Video Mark , And Great Idea With The Plastic Block To Keep It In The Middle

Really helpful video, I have the daunting task of wiring up six double slips this morning.

Another excellent video Mark. It'll be great once the panel is in place. Atb Andy

Good Video, and could follow the wiring. was not that long obly a two biscit video, and one cup coffee lol. take care, stay safe, and have fun.

Wow, wiring two rail track is a LOT more complicated than 3 rail!

In your video where you installed a double switch point, how did you get the power from the outside rail to the inside rail for the engine to cross over from one loop to another with out changing controlers.

Hi Mark. Did you remove the springs from each end of the double slip before installing the point motors

Great video, keep them coming. I'm new to model rail and I'm practicing the electrics on a 4x2 board prior to getting my train room. Please, if I may ask, what size heat shrink do you use and where do you get it from, I'm only using 7/0.2 wire for my point motors, is the the size you are using ? In anticipation of your help cheers and regards.

hi this is the best video I have BUT it’s the last bit of wiring I am having trouble with. The droppers from the centre of the double slip - Do you split them so that they go into both switches or how does it work? I am using DCC but points and slips being run off a separate DC supply through panel and CDU

Stupid question really, but is this for dcc or dc

If it has double slips or wheels it will give you trouble.