66 C10 Budget Build- LS Swap part 1

Подписаться 3 тыс.

Просмотров 3,4 тыс.

50% 1

In this episode, I start the LS swap and get the motor and harness installed and go over some of the parts i used, as well as listing all these parts below with links of where to get them. These are not affiliate links and i make no money off them, so if you find a comparable part for less, do it your way.
BP Automotive Swap Harnesses: bp-automotive....
Speed Engineering Headers: speed-engineer...
Tinworks Fabrication LS Swap motor mounts: tinworksfabric...
Dirty Dingo Power Steering fitting adapter: a.co/d/0ETyjaz
Oil Pressure Adapter fitting: a.co/d/6AiDfWW
Transmission Crossmember: a.co/d/cqPCO02
Power Steering Return hose: a.co/d/8aQzXc4
Power Steering pressure hose: a.co/d/cy8eRY2
4l60 6AN cooler line fittings: a.co/d/e4RGDsz
2 1/8" Hole saw for Harness: a.co/d/9JxBEGP
Knock Sensor relocation: www.ebay.com/i...
Low Profile Oil Pan: www.ebay.com/i...
Fuel rail to 6AN fittings: a.co/d/cDSzMLg
ICT Billet valley cover: a.co/d/8TBlikn

Авто/Мото

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@carlwaybrightjr.9082 23 дня назад

Appreciate your knowledge, will definitely help with my truck! Thanks

@arkansasjon2171 23 дня назад

@@carlwaybrightjr.9082 thank you, glad to be of any help!

@lgh1157 Месяц назад

Great video, lots of good info, Thank you

@arkansasjon2171 Месяц назад

@@lgh1157 thank you!

@bluecollarperformance1331 6 месяцев назад

That crossmember is really going to help out your exhaust guys 😁

@johngray4107 Месяц назад

Just wandering what headers you went with? Thanks....Very good videos. Just starting the swap on my 65.

@arkansasjon2171 Месяц назад

Both of my trucks i have used the Speed Engineering LS Swap shorty headers, you can find them here: speed-engineering.com/collections/universal-ls-lt-swap-parts-exhaust/products/speed-engineering-ls-swap-shorty-headers-camaro-chevelle-nova-c10-k10-obs-truck

@arkansasjon2171 Месяц назад

Also, all the parts i use i try to add to the description in the video with links, so if you look there it shows everything else i used. Hope that helps and good luck!

@Hotrodding Месяц назад

Did you still have to run a wire from the alternator to the starter?

@arkansasjon2171 Месяц назад

@@Hotrodding I just use the stock power block from the LS motor with the red plastic cover and the stock cable that comes from the starter to that post and then chop it off right after the lug where it continues to the factory under-hood fuse box. If you don’t have the factory cable, you will have to tie the alternator and starter back to the battery. But no voltage regulator is required with the LS alternator

@Hotrodding Месяц назад

@@arkansasjon2171 ok thanks alot.

@briangoudreau5793 Месяц назад

What are those from I need a set of 6 lug wheels

@arkansasjon2171 Месяц назад

@@briangoudreau5793 I’m not positive but I think they are off a work truck or express van, the guy I got them from never mentioned what they were off

@heathhylton4746 2 месяца назад

Does that transmission crossmember work with the transmission that comes with LS motor?

@arkansasjon2171 2 месяца назад

@@heathhylton4746 yes, you will either need to buy a new pad or re-use your old mounting pad. It lines up with one bolt hole on each side for me and I just had to drill an additional hole on each side, but the holes on the crossmember are slotted and give plenty of room for location

@heathhylton4746 2 месяца назад

@@arkansasjon2171 I appreciate it! I wanted to make sure because on the Amazon page for the crossmember, it only said that TH350, TH400 and 700R4 transmissions work with it. I didn’t see anything about any other transmissions.

@arkansasjon2171 2 месяца назад

@@heathhylton4746 I can confirm it works just fine with 4L60E. They basically use all the same mounting stuff so you should be good. It’s a nice and cheap crossmember.

@heathhylton4746 2 месяца назад

@@arkansasjon2171 I believe you. I knew that the 700R4 and the 4L60E were very similar but the 4L60E is an upgrade to the 700R4. I’m restoring a 70 C10 and I am buying LS 5.3 and your video is very informative and it helps direct me in the right path to achieve the LS swap in a more affordable way! I appreciate it!

@arkansasjon2171 2 месяца назад

@@heathhylton4746 that’s great! I don’t get a lot of views but I appreciate helping anyone I can, I learn most of what I know through watching others videos as well, RU-vid is a wonderful resource for all of us. Thank you for the comments!